The ESP32-BlueJammer (Bluetooth jammer, BLE jammer, WiFi jammer, RC jammer) disrupts 2.4GHz communications. Using an ESP32 and nRF24 modules, it generates noise and unnecessary packets, causing interference between the devices communicating, making them unable to work as intended. Ideal for controlled disruption and security testing.
README.md
Emensta71450f0187ad
diff --git a/README.md b/README.mdindex 26821de..71bd968 100644--- a/README.md+++ b/README.md@@ -23,6 +23,7 @@ Remember that jamming is illegal and should not be used with malicious intent!## Want to buy one? - [Don Anon Tech's online-shop](https://datechlabs.com/products/the-blue-esp-pre-order)If you are looking forward to purchasing a finished, working, pre-built ESP32 BlueJammer board, you can check out [Don Anon Tech's online-shop](https://datechlabs.com/products/the-blue-esp-pre-order)! There we published the assembled PCB “The Blue ESP” "The Blue ESP" ;p+@@ -67,15 +68,15 @@ If you are looking forward to purchasing a finished, working, pre-built ESP32 Bl### Additional:-- **3rd Antenna:** IPEX to SMA-F pigtail+- **for 3rd Antenna:** IPEX to SMA-F pigtail+- **Status LED:** 3mm LED+- **4.7k Ohm Resistor**### If you're looking to add a battery:- **3.7V Li-Ion Battery**- **JST PH 2.0 Connector**- **TP4056 Charging Module**-- **3mm LED** (blue)-- **4.7k Ohm Resistor**- **Mini Slide Switch**### To screw the 3D printed case together you must have:@@ -88,7 +89,7 @@ If you are looking forward to purchasing a finished, working, pre-built ESP32 Bl## AntennasA frequently asked question is whether the antennas are needed and what the third antenna is for, here is the answer:Yes, you need at least both antennas for the nRF24's! Why? To have it working on a decent range!-The average range with standart known chinese 2.4GHz antennas is about 20meters. Upgrading those antennas will help a lot with getting more range!+The average range with standard known chinese 2.4GHz antennas is about 20meters. Upgrading those antennas will help a lot with getting more range!2 antennas are for the HSPI and VSPI nRF24 modules!@@ -137,16 +138,24 @@ Here are both pinouts for HSPI and VSPI. You need both nRF24L01 modules connecte| MISO | GPIO 19 || IRQ | |-### Battery mod (optional)-| 3.7V Li-Ion battery | JST-PH2 connector | TP4056 Charging Module | Mini Slide Switch | ESP32 | 4.7k Ohm Resistor | 3mm Status LED (blue)|-|---------------------|----------------------|------------------------|-------------------|-------|-------------------|----------------------|-| (+) Battery | (+) JST-PH2 | Bat + | | | | |-| (-) Battery | (-) JST-PH2 | Bat - | | | | |-| | | OUT + | Switch in | | | |-| | | OUT - | | GND | | (-) LED |-| | | | Switch out | 3V3 | | |-| | | | | | Resistor | (+) LED |-| | | | |GPIO27 | Resistor | |+### Status LED+| ESP32 | 4.7k Ohm Resistor | 3mm Status LED (blue)|+|-------|-------------------|----------------------|+| GND | | (-) LED |+| | | |+| | Resistor | (+) LED |+|GPIO27 | Resistor | |++### Additional modifications (battery)+| 3.7V Li-Ion battery | JST-PH2 connector | TP4056 Charging Module | Mini Slide Switch | ESP32 |+|---------------------|----------------------|------------------------|-------------------|-------|+| (+) Battery | (+) JST-PH2 | Bat + | | |+| (-) Battery | (-) JST-PH2 | Bat - | | |+| | | OUT + | Switch in | |+| | | OUT - | | GND |+| | | | Switch out | 3V3 |+| | | | | |+| | | | |GPIO27 |### Schematics