Making an ESP32-based quadcopter from scratch
Python arduinoautopilotcontrol-theorydroneesp32flight-controlflight-controllermavlinkquadcopterquadcopter-firmwareuav
Various minor changes
Oleg Kalachev91173d06c9f0
diff --git a/README.md b/README.mdindex c7da620..28da1b8 100644--- a/README.md+++ b/README.md@@ -73,7 +73,7 @@ Additional articles:|-|-|:-:|:-:||Microcontroller board|ESP32 Mini.<br>ESP32-S3/ESP32-C3 boards are also supported.|<img src="docs/img/esp32.jpg" width=100>|1||IMU (and barometer¹) board|GY‑91, MPU-9265 (or other MPU‑9250/MPU‑6500 board)<br>ICM20948V2 (ICM‑20948)<br>GY-521 (MPU-6050)|<img src="docs/img/gy-91.jpg" width=90 align=center><br><img src="docs/img/icm-20948.jpg" width=100><br><img src="docs/img/gy-521.jpg" width=100>|1|-|Boost converter (optional, for more stable power supply)|5V output|<img src="docs/img/buck-boost.jpg" width=100>|1|+|*Boost converter (optional, for more stable power supply)*|*5V output*|<img src="docs/img/buck-boost.jpg" width=100>|1||Motor|8520 3.7V brushed motor.<br>Motor with exact 3.7V voltage is needed, not ranged working voltage (3.7V — 6V).<br>Make sure the motor shaft diameter and propeller hole diameter match!|<img src="docs/img/motor.jpeg" width=100>|4||Propeller|55 mm or 65 mm|<img src="docs/img/prop.jpg" width=100>|4||MOSFET (transistor)|100N03A or [analog](https://t.me/opensourcequadcopter/33)|<img src="docs/img/100n03a.jpg" width=100>|4|diff --git a/docs/troubleshooting.md b/docs/troubleshooting.mdindex 8f06718..28af53f 100644--- a/docs/troubleshooting.md+++ b/docs/troubleshooting.md@@ -5,7 +5,7 @@Do the following:* **Check ESP32 core is installed**. Check if the version matches the one used in the [tutorial](usage.md#building-the-firmware).-* **Check libraries**. Install all the required libraries from the tutorial. Make sure there are no MPU9250 or other peripherals libraries that may conflict with the ones used in the tutorial.+* **Check libraries**. Install all the required libraries from the tutorial. Make sure there are no MPU-9250 or other peripherals libraries that may conflict with the ones used in the tutorial.* **Check the chosen board**. The correct board to choose in Arduino IDE for ESP32 Mini is *WEMOS D1 MINI ESP32*.## The drone doesn't flydiff --git a/docs/usage.md b/docs/usage.mdindex 5984a32..16123c8 100644--- a/docs/usage.md+++ b/docs/usage.md@@ -329,7 +329,7 @@ To setup ESP-NOW communication:espnow 7a:c8:e3:eb:bf:e9 &PiuSysxP9+$L&5E```- Run this line as a console command on each drone you want to bind to this proxy board.+ Run this line as a console command on each drone you want to bind to this proxy board. [The maximum number](https://github.com/espressif/esp-idf/blob/e95cab4be8fd293e3f3323181e7a2280874da6f7/components/esp_wifi/include/esp_now.h#L32-L33) of simultaneously connected drones is 20 (unencrypted) io 6 (encrypted).3. Set the `WIFI_MODE` parameter to `3` on the drone:diff --git a/flix/mavlink.ino b/flix/mavlink.inoindex 0fae287..a635947 100644--- a/flix/mavlink.ino+++ b/flix/mavlink.ino@@ -241,7 +241,7 @@ void handleMavlink(const void *_msg) {}if (m.command == MAV_CMD_COMPONENT_ARM_DISARM) {- if (m.param1 && controlThrottle > 0.05) return; // don't arm if throttle is not low+ if (m.param1 == 1 && controlThrottle > 0.05) return; // don't arm if throttle is not lowaccepted = true;armed = m.param1 == 1;}diff --git a/flix/motors.ino b/flix/motors.inoindex 3289755..b25e61a 100644--- a/flix/motors.ino+++ b/flix/motors.ino@@ -14,10 +14,7 @@ int pwmStop = 0;int pwmMin = 0;int pwmMax = -1; // -1 means duty cycle mode-const int MOTOR_REAR_LEFT = 0;-const int MOTOR_REAR_RIGHT = 1;-const int MOTOR_FRONT_RIGHT = 2;-const int MOTOR_FRONT_LEFT = 3;+const int MOTOR_REAR_LEFT = 0, MOTOR_REAR_RIGHT = 1, MOTOR_FRONT_RIGHT = 2, MOTOR_FRONT_LEFT = 3;void setupMotors() {print("Setup Motors\n");diff --git a/flix/parameters.ino b/flix/parameters.inoindex 6533110..f1dd5df 100644--- a/flix/parameters.ino+++ b/flix/parameters.ino@@ -6,13 +6,11 @@#include <Preferences.h>#include "util.h"-extern int channelZero[16];-extern int channelMax[16];+extern int channelZero[16], channelMax[16];extern int rollChannel, pitchChannel, throttleChannel, yawChannel, armedChannel, modeChannel;-extern int rcRxPin;+extern int rcRxPin, voltagePin;extern int wifiMode, wifiLongRange, udpLocalPort, udpRemotePort, espnowChannel;extern float rcLossTimeout, descendTime;-extern int voltagePin;extern float voltageScale;extern LowPassFilter<float> voltageFilter;diff --git a/flix/wifi.ino b/flix/wifi.inoindex 5c87828..bfd5061 100644--- a/flix/wifi.ino+++ b/flix/wifi.ino@@ -8,7 +8,7 @@#include <WiFiUdp.h>#include <MacAddress.h>#include <ESP32_NOW_Serial.h>-#include "Preferences.h"+#include <Preferences.h>#include "util.h"extern Preferences storage; // use the main preferences storage@@ -33,10 +33,14 @@ void setupWiFi() {if (wifiMode == W_AP) {WiFi.softAP(storage.getString("WIFI_AP_SSID", "flix").c_str(), storage.getString("WIFI_AP_PASS", "flixwifi").c_str());udp.begin(udpLocalPort);- } else if (wifiMode == W_STA) {+ }++ if (wifiMode == W_STA) {WiFi.begin(storage.getString("WIFI_STA_SSID", "").c_str(), storage.getString("WIFI_STA_PASS", "").c_str());udp.begin(udpLocalPort);- } else if (wifiMode == W_ESPNOW) {+ }++ if (wifiMode == W_ESPNOW) {WiFi.mode(WIFI_AP);WiFi.setChannel(espnowChannel);espnow.addr(MacAddress(storage.getString("ESPNOW_PEER_MAC", "FF:FF:FF:FF:FF:FF").c_str()));