Making an ESP32-based quadcopter from scratch
Python arduinoautopilotcontrol-theorydroneesp32flight-controlflight-controllermavlinkquadcopterquadcopter-firmwareuav
Some fixes in docs
Oleg Kalachev9bffe5b52f21
diff --git a/README.md b/README.mdindex d9907a7..42425a1 100644--- a/README.md+++ b/README.md@@ -77,7 +77,7 @@ Additional articles:|Motor|8520 3.7V brushed motor.<br>Motor with exact 3.7V voltage is needed, not ranged working voltage (3.7V — 6V).<br>Make sure the motor shaft diameter and propeller hole diameter match!|<img src="docs/img/motor.jpeg" width=100>|4||Propeller|55 mm (alternatively 65 mm)|<img src="docs/img/prop.jpg" width=100>|4||MOSFET (transistor)|100N03A or [analog](https://t.me/opensourcequadcopter/33)|<img src="docs/img/100n03a.jpg" width=100>|4|-|Pull-down resistor|10 kΩ|<img src="docs/img/resistor10k.jpg" width=100>|4|+|Pull-down resistor<br>Voltage measurement resistor|10 kΩ|<img src="docs/img/resistor10k.jpg" width=100>|6||3.7V Li-Po battery|LW 952540 (or any compatible by the size)|<img src="docs/img/battery.jpg" width=100>|1||Battery connector cable|MX2.0 2P female|<img src="docs/img/mx.png" width=100>|1||Li-Po Battery charger|Any|<img src="docs/img/charger.jpg" width=100>|1|@@ -154,10 +154,12 @@ You can see a user-contributed [variant of complete circuit diagram](https://mir|VIN|VCC (or 3.3V depending on the receiver)||Signal (TX)|GPIO4¹|-*¹ — UART2 RX pin was [changed](https://docs.espressif.com/projects/arduino-esp32/en/latest/migration_guides/2.x_to_3.0.html#id14) to GPIO4 in Arduino ESP32 core 3.0.*+ *¹ — UART2 RX pin was [changed](https://docs.espressif.com/projects/arduino-esp32/en/latest/migration_guides/2.x_to_3.0.html#id14) to GPIO4 in Arduino ESP32 core 3.0.** Optionally connect the battery voltage divider for voltage monitoring to any ADC1 pin (e. g. *GPIO32* on ESP32, *GPIO3* on ESP32S3).+ ESP32 and ESP32S3 [can measure](https://docs.espressif.com/projects/arduino-esp32/en/latest/api/adc.html#analogsetattenuation) up to 3.1 V and ESP32S3/ESP32C3 can measure up to 2.5 V, so choose the voltage divider resistors accordingly.+## Resources* Telegram channel on developing the drone and the flight controller (in Russian): https://t.me/opensourcequadcopter.diff --git a/tools/pyflix/README.md b/tools/pyflix/README.mdindex ade6d4a..583d510 100644--- a/tools/pyflix/README.md+++ b/tools/pyflix/README.md@@ -30,7 +30,7 @@ flix = Flix() # create a Flix object and wait for connection### Telemetry-Basic telemetry is available through object properties. The property names generally match the corresponding variables in the firmware itself:+Basic telemetry is available through object properties. The property names generally match the corresponding variables in the firmware code:```pythonprint(flix.connected) # True if connected to the drone