Making an ESP32-based quadcopter from scratch
Python arduinoautopilotcontrol-theorydroneesp32flight-controlflight-controllermavlinkquadcopterquadcopter-firmwareuav
Some updates to docs
Oleg Kalacheve81e84e7fc00
diff --git a/README.md b/README.mdindex 42425a1..281eee3 100644--- a/README.md+++ b/README.md@@ -53,7 +53,7 @@ The simulator is implemented using Gazebo and runs the original Arduino code:<img src="docs/img/simulator1.png" width=500 alt="Flix simulator">-## Documentation+## Documentation articles1. [Assembly instructions](docs/assembly.md).2. [Usage: build, setup and flight](docs/usage.md).@@ -75,10 +75,10 @@ Additional articles:|IMU (and barometer¹) board|GY‑91, MPU-9265 (or other MPU‑9250/MPU‑6500 board)<br>ICM20948V2 (ICM‑20948)³<br>GY-521 (MPU-6050)³⁻¹|<img src="docs/img/gy-91.jpg" width=90 align=center><br><img src="docs/img/icm-20948.jpg" width=100><br><img src="docs/img/gy-521.jpg" width=100>|1||Boost converter (optional, for more stable power supply)|5V output|<img src="docs/img/buck-boost.jpg" width=100>|1||Motor|8520 3.7V brushed motor.<br>Motor with exact 3.7V voltage is needed, not ranged working voltage (3.7V — 6V).<br>Make sure the motor shaft diameter and propeller hole diameter match!|<img src="docs/img/motor.jpeg" width=100>|4|-|Propeller|55 mm (alternatively 65 mm)|<img src="docs/img/prop.jpg" width=100>|4|+|Propeller|55 mm or 65 mm|<img src="docs/img/prop.jpg" width=100>|4||MOSFET (transistor)|100N03A or [analog](https://t.me/opensourcequadcopter/33)|<img src="docs/img/100n03a.jpg" width=100>|4||Pull-down resistor<br>Voltage measurement resistor|10 kΩ|<img src="docs/img/resistor10k.jpg" width=100>|6|-|3.7V Li-Po battery|LW 952540 (or any compatible by the size)|<img src="docs/img/battery.jpg" width=100>|1|+|3.7V Li-Po battery|LW 952540 (or any compatible by the size).<br>Make sure the battery has enough discharge rate — 25C or more!|<img src="docs/img/battery.jpg" width=100>|1||Battery connector cable|MX2.0 2P female|<img src="docs/img/mx.png" width=100>|1||Li-Po Battery charger|Any|<img src="docs/img/charger.jpg" width=100>|1||Screws for IMU board mounting|M3x5|<img src="docs/img/screw-m3.jpg" width=100>|2|diff --git a/docs/assembly.md b/docs/assembly.mdindex b23c113..a332272 100644--- a/docs/assembly.md+++ b/docs/assembly.md@@ -28,6 +28,8 @@ Soldered components ([schematics variant](https://miro.com/app/board/uXjVN-dTjoo<img src="img/assembly/7.jpg" width=600>+See an alternative assembly process photos here: https://drive.google.com/drive/folders/1FG5BH9RCzdf1XmJcC70PymiRMXcz6Fx7?usp=sharing.+## Motor directions> [!WARNING]