Skip to content

armgit / moss

Public Imported from GitHub
0

MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.

Python
24.1 KB
Raw Blame

Assembly guide

Prepare the parts and fasteners for one step, then watch its short clip. Quantities are for one rover unless the text says per wheel. Computer and camera alternatives must not be added together.

Seven coordinated clips cover part identification, five exploded assemblies and road-wheel fastening. Use the reference list to match every spacer and shaft collar.

Build MOSS in this order:

Stage Steps
Hull and wheel assemblies 01–04
Tracks and running gear 05–11
Hull electronics and sensors 12–17
Arm and gripper 18–19
Cover and bin 20

Hull and wheel assemblies

01. Choose the hull and fit the inserts

Prepare Quantity
One-piece hull · PETG · Hull One Piece 1
Lidar Base R84 · PETG 1
Rear hull — motors and computer · PETG · Hull Split 1
Front hull — battery and camera · PETG · Hull Split 1
Epoxy from the two-part kit, for the hull joint As needed
M3 heat-set insert, OD4 mm, length 6 mm 11
Split hull only: M4 × 15 socket-head screw 6
Split hull only: M4 hex nut, 7 mm across flats 6
Split hull only: M4 washer, Ø9 × 0.8 mm 6

Current R92 split hull, motor/computer half and battery/camera half

  1. Choose the one-piece hull or both split halves. For the split hull, dry-fit both halves first, then apply a thin layer of two-part epoxy to the mating faces. Engage the locating pins, seat six nuts from the battery side, and fit six M4 × 15 screws with washers from the motor/computer side. Tighten progressively and let the epoxy cure before installing electronics or the battery.
  2. Use a soldering iron to fit the inserts: place each insert over its hole, heat it with the iron tip, then gently press it straight into the plastic. Fit four inserts for the cover, four for the arm plate and two for the LiDAR base in the hull.
  3. Use the same soldering-iron method to fit the remaining insert in the LiDAR base for the carriage lock. Keep the threads clear and let all inserts cool before fitting screws.

02. Build the six road wheels

Prepare Quantity
Road wheel inner half · PETG 6
Road wheel outer half · PETG 6
SP09 · Road wheel centre spacer · PETG 6
625 bearing 12
M3 × 35 socket-head screw 18
M3 hex nut 18
  1. For each wheel, prepare two printed halves, one SP09 centre spacer, two 625 bearings, three M3 × 35 screws and three M3 nuts.
  2. Insert each bearing through the open mating face of its wheel half. Do not push it through the smaller outside opening.
  3. Seat the three nuts in the inner half, position SP09 between the bearings, close the wheel halves, then insert the three screws from the outer face. Repeat six times.

Watch the fastening example

03. Build the two drive wheels

Prepare Quantity
Left HEX12 drive wheel inner half R13 · PETG 1
Left HEX12 drive wheel outer half R13 · PETG 1
Right HEX12 drive wheel inner half R13 · PETG 1
Right HEX12 drive wheel outer half R13 · PETG 1
HEX12 metal hub, 6 mm bore, 18 mm length 2
M3 × 20 socket-head screw 6
M3 hex nut 6
Hub set screws, supplied with the metal hubs (2 per hub) 4
  1. Match the locating feature on each pair of halves.
  2. Close each wheel with three M3 × 20 screws and three M3 nuts. Keep the HEX12 seat clear.
  3. Insert one HEX12 metal hub (6 mm bore, 18 mm length) into the hexagonal seat of each printed drive wheel. The motors used in the original MOSS build came with a gold-coloured hub and two set screws per motor. If your motor kit does not include them, order two HEX12 metal hubs (6 mm bore, 18 mm length), each with two matching set screws, separately.
  4. Keep the two hub set screws accessible through the side openings in the printed wheel. These screws secure the metal hub to the 6 mm steel drive axle. Tighten them when fitting the axle in step 08.

04. Build the two idler wheels

Prepare Quantity
Left 22T idler wheel inner half R13 · PETG 1
Left 22T idler wheel outer half R13 · PETG 1
Right 22T idler wheel inner half R13 · PETG 1
Right 22T idler wheel outer half R13 · PETG 1
SP10 · Idler centre spacer · PETG 2
608 bearing 4
M3 × 25 socket-head screw 6
M3 hex nut 6
  1. For each idler, seat two 608 bearings with SP10 (centre spacer) between them.
  2. Close the two halves with three M3 × 25 screws and three M3 nuts. Repeat for the other side.

Tracks and running gear

05. Fit the motors and inner bearing retainers

Prepare Quantity
Motor Mount Left R90 · PETG 1
Motor Mount Right R90 · PETG 1
Motor bearing inner retainer · PETG 2
JGB37-520 motor, 12 V, 90:1, 110 rpm, Hall encoder 2
626 bearing, inner 2
Rigid coupling, 6 mm to6 mm 2
M4 × 20 socket-head screw 8
M4 hex nut 8
M3 × 8 socket-head screw 12
  1. Use three M3 × 8 screws per motor, without washers. The other six M3 × 8 screws secure the two bearing retainers.
  2. Put four M4 nuts into each motor-support nut pocket and secure each support to the hull with four M4 × 20 screws.
  3. Fit the inner bearing retainers with three M3 × 8 screws per side.

06. Fit the inner track frames

Prepare Quantity
Left inner track frame R12 C2 · PETG 1
Right inner track frame R12 C2 · PETG 1
M4 × 15 socket-head screw 6
M4 hex nut 6
  1. Fit each inner frame directly against the hull.
  2. Use three M4 × 15 screws and three M4 nuts per side.

07. Fit road-wheel axles and spacer pairs

Prepare Quantity
SP01 · Road wheel inner spacer · PETG 6
SP02 · Road wheel outer spacer · PETG 6
Smooth steel axle, 5 x70 mm finished length 6
LK05 — shaft collar: 5 mm bore, 10 mm outside diameter, 5 mm long 12
  1. Use SP01 (1 dot, 7.5 mm) on the inside and SP02 (2 dots, 5.5 mm) on the outside of every road wheel. SP09 (18 mm, no dots) sits between its bearings.
  2. Retain each axle with two LK05 collars (5 mm bore). Repeat for all six wheels and check free rotation.

Watch the exploded assembly

08. Fit the drive axles and outer bearing covers

Prepare Quantity
SP03 · Drive motor side spacer · PETG 2
SP04 · Drive outer spacer · PETG 2
Motor bearing outer cover · PETG 2
SP11 · Drive bearing to collar spacer · PETG 2
Smooth steel axle, 6 x77 mm finished length 2
626 bearing, outer 2
LK06 — shaft collar: 6 mm bore, 11 mm outside diameter, 5 mm long 2
M3 × 15 socket-head screw 6
M3 hex nut 6
  1. Dry-fit each drive wheel and its metal hub on the 6 mm steel drive axle. Mark where the two opposing hub set screws meet the axle.
  2. Remove the axle and lightly sand two small, shallow flats at those marks, one on each side. Keep the bearing seats round and remove burrs and sanding dust before assembly. The flats help prevent the hub from slipping on the axle.
  3. Use SP03 (3 dots, 7.6 mm) on the motor side and SP04 (4 dots, 12.6 mm) on the outer side of the drive wheel.
  4. Align the two hub set screws with the flats and tighten both with an Allen key through the wheel openings, one from each side. Check that the wheel and axle turn together without slipping.
  5. Put SP11 (3.5 mm, no dots) between the outer 626 bearing and LK06 (6 mm bore). Secure each bearing cover with three M3 × 15 screws and nuts.

Watch the exploded assembly

09. Fit the idler slides and tensioners

Prepare Quantity
Left inner tensioner cover R12 C2 · PETG 1
Right inner tensioner cover R12 C2 · PETG 1
SP05 · Idler inner spacer · PETG 2
SP06 · Idler outer spacer · PETG 2
Left Cover tensioner outer · PETG 1
Right Cover tensioner outer · PETG 1
Tensioner slider · PETG 4
SP07 · Idler inner retainer spacer · PETG 2
SP08 · Idler outer retainer spacer · PETG 2
Smooth steel axle, 8 x87 mm finished length 2
LK08 — shaft collar: 8 mm bore, 16 mm outside diameter, 8 mm long 4
M3 × 15 socket-head screw 16
M3 hex nut 16
M4 × 35 socket-head screw 4
M4 hex nut 8
M4 washer 4
  1. Inside to outside: LK08, SP07, inner slider, SP05, idler wheel with SP10 between its bearings, SP06, outer slider, SP08, LK08. Use two LK08 collars (8 mm bore) per axle.
  2. Fit each tensioner cover with four M3 × 15 screws and nuts. Use an M4 × 35 adjuster with its washer and two nuts at each of the four tensioners.

All four tensioner sliders are the same printed part. Rotate each slider to match its inner or outer position shown in the assembly; do not print a separate mirrored version.

Watch the exploded assembly

10. Close the track frames

Prepare Quantity
Left Outer Track Frame R32 · PETG 1
Right Outer Track Frame R32 · PETG 1
SP12 · Track frame cross-member spacer · PETG 4
M4 × 60 socket-head screw 4
M4 hex nut 4
M4 washer 4
  1. Put the two SP12 cross-member spacers (41 mm, no dots) in each side assembly.
  2. Fit the outer frame using two M4 × 60 screws, washers and nuts per side.

Watch the exploded assembly

11. Fit the tracks

Prepare Quantity
  1. Use the 70-tooth track print masters supplied in this package.
  2. Seat the central guides in the wheel grooves. Adjust both ends evenly and turn each track by hand.

Hull electronics and sensors

12. Fit the driver and controller

Prepare Quantity
Cytron MDD10A Rev2 dual motor driver 1
Adafruit QT Py ESP32-S3, 5426 1
Adafruit Terminal Block BFF, 6495 1
Adafruit INA219 STEMMA QT, 904 1
M3 × 6 socket-head screw 4
M2 × 6 screw, non-countersunk 6
M2 washer, 0.3 mm thick 6
  1. Secure the MDD10A with four M3 × 6 screws.
  2. Use four M2 × 6 screws and 0.3 mm washers for the BFF, and two of each for the INA219.

13. Fit the speaker and amplifier

Prepare Quantity
Speaker, 3 W, 4 ohm, 2-pin connector with 2 mm pitch 1
MAX98357A amplifier module 1
Splash-resistant acoustic membrane, fitted to the inner grille lip 1
M3 × 6 socket-head screw 2
M2 × 6 screw, non-countersunk 2
M2 washer, 0.5 mm thick 2
  1. Fix the speaker with two M3 × 6 screws above its grille.
  2. Seat the amplifier on its two mounting posts and two support pillars. Use two M2 × 6 screws with 0.5 mm washers.

14. Fit the computer carrier and servo adapter

Prepare Quantity
Pi Adapter R87 · PETG · Compute Pi 1
Jetson Adapter R87 · PETG · Compute Jetson 1
JT01 · Jetson retaining tab 1 · PETG · Compute Jetson 1
JT02 · Jetson retaining tab 2 · PETG · Compute Jetson 1
Waveshare Bus Servo Adapter A 1
Pi only: HAT mounting screws and spacers, supplied with the HAT 1 kit
M3 × 6 socket-head screw 2
M3 × 8 socket-head screw 2
M3 washer, 0.5 mm thick 4
M2.5 × 8 screw, non-countersunk 4
M2.5 washer, 0.5 mm thick 4
Jetson only: M3 × 8 socket-head screw, no washer 2
  1. Choose one carrier: Jetson or Pi.
  2. Use the two M3 × 6 screws at the front and the two M3 × 8 screws at the rear, with one 0.5 mm washer each.
  3. For Jetson, secure the two retaining tabs with two M3 × 8 screws, without washers.
  4. For Pi/HAT, use the screws and spacers supplied with the HAT; prepare this assembly before fitting the carrier in the hull.

15. Fit the camera option

Prepare Quantity
Gemini Window Adapter R89 · PETG · Camera Gemini 1
RealSense Insert R72 · PETG · Camera Realsense 1
Gemini Flush Insert R72 · PETG · Camera Gemini 1
RealSense D455 OR Orbbec Gemini 2 1
RealSense only: M4 × 10 socket-head screw 2
Gemini only: M3 × 8 socket-head screw 2
  1. For RealSense, slide the support insert down from the top, then use its two M4 × 10 screws.
  2. For Gemini, use the flush insert and the window bezel instead. Secure the camera with two M3 × 8 screws; keep the USB opening clear.

16. Fit the LiDAR carriage

Prepare Quantity
Lidar dovetail carriage R21 · PETG 1
SLAMTEC RPLIDAR C1 1
M3 × 10 socket-head screw 2
M2.5 × 6 socket-head screw 4
M3 × 20 socket-head screw 1
  1. With the carriage removed, secure the LiDAR base to the hull with two M3 × 10 screws.
  2. Secure the C1 to the carriage with four M2.5 × 6 screws, slide it onto the base and lock it with the M3 × 20 screw, without a washer, into the M3 insert.

17. Fit power distribution and cooling

Prepare Quantity
XT30 distribution base · PETG 1
XT30 distribution lid · PETG 1
XT30 insulating separator · PETG 1
3010 fan, 12 V 2
Emergency stop LA16-11ZS/A, 16 mm 1
KCD11 two-pin rocker switch and splash cover 1
12-cell battery pack, 3S4P, with BMS, 110 × 67 × 35 mm 1
Power harness wire, fuse and USB cables 1
DC male barrel plug, 5.5 × 2.5 mm, 9.5 mm barrel, centre positive — Jetson power 1
DC male barrel plug matching the input of the Pi 5 V power supply 1
DC male barrel plug, 5.5 × 2.1 mm — Waveshare Bus Servo Adapter A power 1
DC male barrel plug, 5.5 × 2.1 mm — battery extension to the panel socket 1
XT30 enclosure connectors: 1 input + 4 outputs, from the BOM connector pairs 5
M2.5 × 10 low-head screw, head diameter 5 mm maximum 4
  1. Clip the two fans into their mounts.
  2. Fit the emergency stop and rocker switch in their hull openings.
  3. Assemble the XT30 base, insulating separator and lid with four low-head M2.5 × 10 screws.

Watch the exploded assembly

Arm and gripper

18. Fit the arm plate and build the arm

Prepare Quantity
Arm Mounting Platform R22 · PLA 1
SO101 Base · PLA 1
SO101 Shoulder rotation · PLA 1
SO101 Base motor holder · PLA 1
SO101 Shoulder bracket cable clip · PLA 1
SO101 Upper arm cable clip · PLA 1
SO101 Forearm cable clip · PLA 1
SO101 Wrist cable clip · PLA 1
SO101 Wrist bracket · PLA 1
ST3215 12 V serial bus servo 5
M3 × 10 socket-head screw 4
M4 × 25 countersunk 90-degree screw 4
M4 hex nut 4
Kit screw: M2 × 6, original servo head 20
Kit screw: M3 × 6, original servo head 37
  1. Fit the arm plate with four M3 × 10 socket-head screws. Do not add washers in the counterbores.
  2. Use the original servo screw packs for the SO101 joints. Keep the camera and servo cables in the printed guides.
  3. For the wrist-camera cable, heat the printed clips to 70 °C, then close them around the cable.

19. Build the gripper and wrist camera

Prepare Quantity
NC90 Right side shield · PLA 1
NC90 Pinion · PLA 1
NC90 Cable guide · PLA 1
NC90 Right jaw extended rack · PLA 1
Gripper Camera Mount R30 · PLA 1
NC90 Left side shield · PLA 1
NC90 Base extended rails · PLA 1
NC90 Left jaw extended rack · PLA 1
CF35-12 gripper servo 1
Wrist USB camera for the R30 mount, 21 × 13.5 mm PCB hole pattern 1
Kit screw: M3 × 6 cross-head ISO7045 11
Kit screw: #1-42 x3/16 inch typeAB 6
M2 × 6 screw, non-countersunk, for wrist camera PCB 4
M3 × 10 socket-head screw, for wrist camera bracket 2
M3 hex nut, for wrist camera bracket 2
  1. Fix the NC90 base to the wrist-roll horn with four M3 × 6 screws from the gripper kit. Check that the screws engage securely and the horn turns freely.
  2. Fit the gripper servo, its horn and pinion. Slide the widened jaws into the rails with both racks aligned on the pinion, then fit the side shields and cable guide with the remaining kit hardware.
  3. Fit the current camera mount. Retain the original gripper screw types.
  4. Fix the R30 camera bracket to the gripper with two M3 × 10 screws and two M3 nuts, without washers. Fix the matching camera PCB with four M2 × 6 screws.

Cover and bin

20. Close the hull and fit the bin

Prepare Quantity
02 Motor access hatch 10 screws · PETG 1
One-piece upper cover · PLA · Cover One Piece 1
14 Bin 20x10x2 magnet pockets · PLA 1
Split cover · rear section · PLA · Cover Split 1
Split cover · LiDAR extension · PLA · Cover Split 1
Magnet, 20 x10 x2 mm 4
Small two-part epoxy adhesive kit, two tubes (resin + hardener), for the magnets and split cover 1 kit
M3 × 10 countersunk 90-degree screw, head diameter 6.4 mm maximum 10
M3 × 10 countersunk 90-degree screw, head diameter 5.6 mm maximum 4

Two-piece upper cover: lower the LiDAR extension into the two dovetail sockets from above

  1. For the split cover: test-fit the two pieces off the rover. Lower the LiDAR extension from above into both dovetail sockets. Apply a thin layer of two-part epoxy on the mating faces, seat the joint, align the outer surfaces and hold until cured. The glued cover then mounts with the same four screws as the one-piece cover.
  2. Close the motor hatch with ten M3 × 10 countersunk screws.
  3. Fit the upper cover with four M3 × 10 countersunk screws.
  4. Check the polarity of all four magnets, then glue them into their pockets with epoxy. Let the epoxy cure before fitting the bin.