Skip to content

armgit / moss

Public Imported from GitHub
0

MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.

Python
5.4 KB
Raw Blame
name,quantity,notes
"Adafruit QT Py ESP32-S3, 8 MB flash/no PSRAM, ref.5426",1,
"Adafruit Terminal Block BFF, ref.6495",1,
"Adafruit INA219 STEMMA QT, ref.904",1,
"STEMMA QT cable, 300 mm, Adafruit 5384",1,
Cytron MDD10A Rev2 dual motor driver,1,
Waveshare Bus Servo Adapter A,1,
MAX98357A amplifier module,1,
"Speaker, 3 W, 4 ohm",1,
Acoustic splash membrane and compatible adhesive,1,EPTFE or non woven fabric membrane.
"JGB37-520, 12 V, 90:1, 110 rpm, Hall encoder, 6 mm D-shaft",2,
625 bearing,12,
608 bearing,4,
626 bearing,4,
"LK05 — shaft collar, 5 mm bore, Ø10 × 5 mm",12,
"LK06 — shaft collar, 6 mm bore, Ø11 × 5 mm",2,
"LK08 — shaft collar, 8 mm bore, Ø16 × 8 mm",4,
"Smooth steel axle, 5 ×70 mm finished length",6,Check the physical stack before cutting stock.
"Smooth steel axle, 6 ×77 mm finished length",2,
"Smooth steel axle, 8 ×87 mm finished length",2,
"Rigid motor-to-shaft coupling, 6 mm bores",2,
"HEX12 metal wheel hub, 6 mm bore, 18 mm length",2,
ST3215 12 V serial bus servo,5,Keep the original servo screw packs.
CF35-12 constant-force gripper servo,1,
"3010 fan, 12 V",2,
"Magnet, 20 ×10 ×2 mm",4,Glue into the pockets with epoxy; check polarity before gluing.
Two-part epoxy adhesive kit (resin + hardener),1,For gluing the four bin magnets and joining the two-piece hull and cover when printing on a smaller printer.
"M3 brass heat-set insert, OD4 mm, length 6 mm",11,10 in the hull and 1 in the LiDAR base.
"12-cell battery pack, 3S4P, with BMS",1,110 × 67 × 35 mm.
12.6 V CC/CV charger for the selected 3S pack,1,
"Emergency stop LA16-11ZS/A, 16 mm",1,
KCD11 two-pin rocker switch and splash cover,1,
"Inline blade-fuse holder, 14 AWG",1,
"ATC blade fuse, 15 A",1,
Amass XT30 male/female connector pair,6,
"DC panel socket, 5.5 ×2.1 mm",2,Female panel-mount sockets.
DC male barrel plug — computer power,1,"Jetson option: 5.5 × 2.5 mm, 9.5 mm barrel, centre positive. Pi option: match the input of the selected 5 V power supply. Choose one."
"DC male barrel plug, 5.5 × 2.1 mm",2,One for Waveshare Bus Servo Adapter A; one for the battery extension.
"Wire, ferrules and heat-shrink",1,One set for the power and signal wiring.
Hoco HB1 four-port USB 2.0 hub,1,
GameSir Nova 2 Lite gamepad with wireless USB receiver,1,For manual driving; include the wireless USB receiver. Used successfully on MOSS.
"USB-C to USB-A cable, 30 cm",3,
RealSense camera cable,1,Lazada product link: https://www.lazada.co.th/products/i16248699269-s127506585857.html · RealSense option only.
Computer — Jetson Orin Nano Super OR Raspberry Pi 5,1,"Choose ONE computer. Pi: add its cooler, storage and appropriate 5 V supply. Use the matching printed carrier; Pi/HAT mounting screws and spacers are supplied with the HAT."
Intel RealSense D455 OR Orbbec Gemini 2,1,Use the matching printed insert(s); these are alternatives.
SLAMTEC RPLIDAR C1,1,
Wrist USB camera for the R30 mount,1,PCB mounting-hole pattern: 21 × 13.5 mm.
"M2 × 6 screw, non-countersunk",12,Controller/INA219: 6; amplifier: 2; wrist-camera PCB: 4.
"M2 washer, 0.3 mm thick",6,Controller/BFF and INA219.
"M2 washer, 0.5 mm thick",2,Amplifier.
M2.5 × 6 socket-head screw,4,LiDAR.
"M2.5 × 8 screw, non-countersunk",4,Servo adapter.
M2.5 × 10 low-head screw,4,Power distribution. Head diameter 5 mm maximum.
"M2.5 washer, 0.5 mm thick",4,Servo adapter.
M3 × 6 socket-head screw,8,Motor driver: 4; speaker: 2; computer carrier: 2.
M3 × 8 socket-head screw,18,14 common screws. Add 2 for the Jetson retaining tabs and 2 for the Gemini option. Total required: 14–18 depending on options.
M3 × 10 socket-head screw,8,LiDAR base: 2; arm plate: 4; wrist-camera bracket: 2.
M3 × 15 socket-head screw,22,Drive axle/outer bearing covers: 6; idler slides/tensioners: 16.
M3 × 20 socket-head screw,7,Drive wheels: 6; LiDAR carriage lock: 1.
M3 × 25 socket-head screw,6,Idler wheels.
M3 × 35 socket-head screw,18,"Six road wheels, 3 screws each."
"M3 × 10 countersunk 90° screw, head Ø6.4 mm maximum",10,Cover and bin assembly.
"M3 × 10 countersunk 90° screw, head Ø5.6 mm maximum",4,Cover and bin assembly; smaller head clearance than the other M3 countersunk screws.
M3 hex nut,54,Road wheels: 18; drive wheels: 6; idlers: 6; bearing covers: 6; tensioners: 16; wrist-camera bracket: 2.
"M3 washer, 0.5 mm thick",4,Computer carrier and servo-adapter assembly.
M4 × 10 socket-head screw,2,RealSense option only. Not needed with Gemini.
M4 × 15 socket-head screw,12,6 for the inner track frames. Add 6 only for the split hull (12 total); monobloc hull uses 6.
M4 × 20 socket-head screw,8,Motor mounts and inner bearing retainers.
M4 × 25 countersunk 90° screw,4,Arm base.
M4 × 35 socket-head screw,4,Track tensioners.
M4 × 60 socket-head screw,4,Outer track frames.
M4 hex nut,36,30 for a monobloc rover. Add 6 for the split hull (36 total); split-hull pockets require 7 mm across flats.
"M4 washer, Ø9 × 0.8 mm",14,8 for tensioners and outer frames. Add 6 for the split hull (14 total).
M2 × 6 original servo screw,20,Supplied with the servo hardware. Keep the original head type; do not buy twice.
M3 × 6 original servo screw,37,Supplied with the servo hardware. Keep the original head type; do not substitute generic socket heads.
"M3 × 6 cross-head screw, ISO 7045",11,Original gripper hardware; retain the supplied screw pack.
#1-42 × 3/16 inch Type AB screw,6,Original gripper hardware; retain the supplied screw pack.