Skip to content

armgit / moss

Public Imported from GitHub
0

MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.

Python
15.5 KB
Raw Blame
{
  "revision": "V1C audited prototype 2026-10-15",
  "supersedes": "V1B is withdrawn as a fabrication candidate",
  "ERC_violations": 0,
  "DRC_violations": 0,
  "unconnected_items": 0,
  "schematic_pcb_parity_issues": 0,
  "assembly_components": 150,
  "BOM_CPL_match": true,
  "order_lines": 59,
  "board": {
    "board_dimensions_mm": [
      60,
      65,
      1.6
    ],
    "corner_radius_mm": 2,
    "mounts": {
      "H3": {
        "center_mm": [
          56.0,
          4.0
        ],
        "drill_mm": [
          2.7,
          2.7
        ]
      },
      "H2": {
        "center_mm": [
          4.0,
          61.0
        ],
        "drill_mm": [
          2.7,
          2.7
        ]
      },
      "H4": {
        "center_mm": [
          56.0,
          61.0
        ],
        "drill_mm": [
          2.7,
          2.7
        ]
      },
      "H1": {
        "center_mm": [
          4.0,
          4.0
        ],
        "drill_mm": [
          2.7,
          2.7
        ]
      }
    },
    "keepout_diameter_mm": 8,
    "all_copper_screw_keepouts": 4,
    "footprint_count": 162,
    "assembled_count": 150,
    "all_components_top": true,
    "track_count": 1621,
    "via_count": 276,
    "minimum_track_width_mm": 0.15,
    "minimum_via_drill_mm": 0.3,
    "planes": [
      {
        "layer": "In1.Cu",
        "net": "GND",
        "filled": true
      },
      {
        "layer": "In2.Cu",
        "net": "GND",
        "filled": true
      }
    ],
    "signal_tracks_on_internal_layers": 0,
    "USB": {
      "USB_P": {
        "total_tree_copper_length_mm": 16.29192,
        "signal_vias": 0,
        "layers": [
          "F.Cu"
        ]
      },
      "USB_N": {
        "total_tree_copper_length_mm": 16.11942,
        "signal_vias": 0,
        "layers": [
          "F.Cu"
        ]
      },
      "ESP_USB_P": {
        "total_tree_copper_length_mm": 1.84,
        "signal_vias": 0,
        "layers": [
          "F.Cu"
        ]
      },
      "ESP_USB_N": {
        "total_tree_copper_length_mm": 1.84,
        "signal_vias": 0,
        "layers": [
          "F.Cu"
        ]
      },
      "measurement_scope": "Total copper tree lengths include reversible-connector branches; these are not per-orientation propagation delays. Parallel core is symmetric. W/S 0.15/0.15 mm; quasi-static estimate is not manufacturer impedance validation."
    },
    "decoupling_ground_via_max_center_distance_mm": 1.1,
    "decoupling_ground_records": [
      {
        "ref": "C26",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          22.5338,
          58.9659
        ]
      },
      {
        "ref": "C40",
        "pin": "2",
        "length_mm": 0.9,
        "via": [
          52.9,
          45.425
        ]
      },
      {
        "ref": "C12",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          59.275,
          47.5
        ]
      },
      {
        "ref": "C4",
        "pin": "2",
        "length_mm": 1.1,
        "via": [
          51.6,
          50.45
        ]
      },
      {
        "ref": "C2",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          39.5,
          34.525
        ]
      },
      {
        "ref": "C29",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          10.2838,
          48.2159
        ]
      },
      {
        "ref": "C23",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          8.25,
          31.375
        ]
      },
      {
        "ref": "C42",
        "pin": "2",
        "length_mm": 0.825,
        "via": [
          45.5,
          42.9
        ]
      },
      {
        "ref": "C9",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          21.75,
          9.625
        ]
      },
      {
        "ref": "C16",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          27.375,
          10.25
        ]
      },
      {
        "ref": "C17",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          25.875,
          19.75
        ]
      },
      {
        "ref": "C20",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          1.125,
          22.25
        ]
      },
      {
        "ref": "C5",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          43.4159,
          51.2588
        ]
      },
      {
        "ref": "C27",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          44.25,
          13.775
        ]
      },
      {
        "ref": "C7",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          42.775,
          43.14
        ]
      },
      {
        "ref": "C1",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          51.25,
          22.625
        ]
      },
      {
        "ref": "C31",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          13.5338,
          53.7159
        ]
      },
      {
        "ref": "C24",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          28.0,
          55.725
        ]
      },
      {
        "ref": "C45",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          13.625,
          19.25
        ]
      },
      {
        "ref": "C44",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          13.625,
          24.75
        ]
      },
      {
        "ref": "C18",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          13.875,
          11.75
        ]
      },
      {
        "ref": "C13",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          48.775,
          57.5
        ]
      },
      {
        "ref": "C41",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          35.9838,
          48.2159
        ]
      },
      {
        "ref": "C43",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          15.0,
          20.875
        ]
      },
      {
        "ref": "C25",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          20.0,
          54.725
        ]
      },
      {
        "ref": "C6",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          42.95,
          45.3
        ]
      },
      {
        "ref": "C10",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          40.0,
          63.025
        ]
      },
      {
        "ref": "C22",
        "pin": "2",
        "length_mm": 0.85,
        "via": [
          1.125,
          34.25
        ]
      },
      {
        "ref": "C21",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          8.25,
          38.225
        ]
      },
      {
        "ref": "C19",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          8.25,
          26.225
        ]
      },
      {
        "ref": "C11",
        "pin": "2",
        "length_mm": 1.0,
        "via": [
          37.9838,
          11.7159
        ]
      }
    ],
    "self_contained_model_paths_checked": 27,
    "limits": "No physical testing, closed-solid rover interference proof, EMC, thermal test, firmware qualification or manufacturing approval."
  },
  "logic_validation": {
    "status": "PASS",
    "warnings": [],
    "physical_pin_assignments_compared": 486,
    "requirements": [
      "Physical latch feedback and native USB pin map",
      "New power IC physical pinmaps, reset supervision and switched encoder pullups",
      "No resistive AMP_5V-to-MCU path",
      "3V3 servo TX, OE default off, I2S reset pulldowns and SD_MODE series protection",
      "Watchdog ENOUT wiring and asynchronous fault-clear topology"
    ],
    "logic": {
      "exhaustive_combinations": 16384,
      "fault_recovery_sequences": 4,
      "physical_pin_mutation_sensitivity_checks": 1,
      "scope": "Actual native pin/net graph and datasheet logic at valid, stable power; no timing, metastability, analogue power ramps or firmware execution."
    },
    "calculations": {
      "buck": {
        "nominal_V": 3.384,
        "static_min_V": 3.3108688111888114,
        "static_max_V": 3.457365045045045,
        "assumptions": "VFB 0.588..0.612 V; independent resistor tolerance extremes; excludes ripple, line/load transients and temperature effects not included in electrical table."
      },
      "supervisor": {
        "assert_threshold_min_V": 3.0184,
        "release_threshold_max_V": 3.1887239999999997,
        "release_headroom_from_static_buck_min_mV": 122.1448111888117,
        "release_delay_ms": [
          130,
          200,
          270
        ],
        "assert_delay_max_us_test_condition": 50,
        "warning": "Does not guarantee reset before 3.0V on a fast collapse. Test the real rail ramp."
      },
      "USB_current_limit_mA": [
        387.2515860133054,
        491.222463889218
      ],
      "watchdog_pullup_uA_at_3V3": 70.2127659574468,
      "encoder_passive_high_nominal_V": 3.0,
      "USB_endpoint_budget": {
        "CDC": 3,
        "UAC_playback_feedback": 2,
        "noncontrol_total": 5,
        "noncontrol_limit": 6,
        "IN_including_EP0": 4,
        "IN_limit": 5
      },
      "INA226_external_2mohm": {
        "15A_mV_W": [
          30,
          0.45
        ],
        "30A_mV_W": [
          60,
          1.8
        ],
        "Current_LSB_A": 0.002,
        "CAL": 1280,
        "Power_LSB_W": 0.05
      }
    },
    "source_sha256": {
      "outputs/MOSS_Core_V1C_20261015/circuit.json": "59eccf55a9b11acb38f95911138c5d1bfa0d8910d6fdb24a23f9697fd0c15ca6",
      "outputs/MOSS_Core_V1C_20261015/netlist_schematic_review.xml": "65e4e9955b844971f2884e99b1ce2e55f9fc7f86d4c79dc87252bf4dc1ad635c"
    },
    "datasheet_model_sources": {
      "HCS21": "https://www.ti.com/lit/ds/symlink/sn74hcs21.pdf",
      "LVC1G17": "https://www.ti.com/lit/ds/symlink/sn74lvc1g17.pdf",
      "LVC74": "https://www.ti.com/lit/ds/symlink/sn74lvc74a.pdf",
      "LVC2G08": "https://www.ti.com/lit/ds/symlink/sn74lvc2g08.pdf",
      "LVC1G08": "https://www.ti.com/lit/ds/symlink/sn74lvc1g08.pdf",
      "LVC1G126": "https://www.ti.com/lit/ds/symlink/sn74lvc1g126.pdf",
      "TPS3431": "https://www.ti.com/lit/ds/symlink/tps3431.pdf",
      "TLV62569": "https://www.ti.com/lit/ds/symlink/tlv62569.pdf",
      "TLV803E": "https://www.ti.com/lit/ds/symlink/tlv803e.pdf",
      "TPS2553": "https://www.ti.com/lit/ds/symlink/tps2553.pdf",
      "TPS22918": "https://www.ti.com/lit/ds/symlink/tps22918.pdf"
    },
    "unvalidated": [
      "Physical behaviour under brownout and partial power",
      "USB enumeration/suspend/current compliance",
      "MCU firmware and host broker",
      "Servo timing and cable load",
      "Manufacturing, EMC/ESD and thermal performance"
    ]
  },
  "schematic_validation": {
    "project": "MOSS Core V1C",
    "parts": 162,
    "connected_pin_assignments_compared": 472,
    "no_connect_pins_checked": 14,
    "connected_pin_mismatches": [],
    "no_connect_mismatches": [],
    "erc_violations": 0,
    "erc_ignored_checks": [
      {
        "description": "Global label only appears once in the schematic",
        "key": "single_global_label"
      },
      {
        "description": "Four connection points are joined together",
        "key": "four_way_junction"
      },
      {
        "description": "SPICE model issue",
        "key": "simulation_model_issue"
      },
      {
        "description": "Assigned footprint doesn't match footprint filters",
        "key": "footprint_filter"
      }
    ],
    "extra_erc_exclusions_added_by_generator": false,
    "library_validation": "Empty global tables; exact project-local MOSS library resolved",
    "schematic_sha256": {
      "01_USB_Power.kicad_sch": "9f201886137ca4cdb1e13916210c4ca38465a7ab7afd5967d6f1d377e827b713",
      "04_Drive_Encoders.kicad_sch": "460a70370a1127d7dcf0d9e77b45e09a2b84ae3d405262bd6b5b38a19575bb85",
      "05_Servo.kicad_sch": "5cc31d71cee329c42503d7d3806b139c5568e6434cff9cc56efba1e81e919f64",
      "03_Hardware_Interlock.kicad_sch": "6ee9b8f470de30aa662cf141ddbe0d5497dec66ba247c2306196f02953ea9b18",
      "07_Current_Sense.kicad_sch": "a2333f5b9dac8e4f0e0d226a85b94c25dec94b436586573cbe71d9efbae339b1",
      "06_Audio.kicad_sch": "41c500f9eecbeec69ced529ca7909184f82e3999658b9d75645fd484b7f46c30",
      "02_Controller.kicad_sch": "01b4afa0cb70a8a28207dd4fb02fcca844a30c19d38b431f1c8e49206cc1a7fc",
      "MOSS_Core_V1C.kicad_sch": "a79132372a7874c866d742643a52ef6c87ef0d133912c6678e77ea2ca4b99909"
    },
    "generator_sha256": "ce7e73e5ca98482a644862ade4a9d3cdf6ec08324e4cdfccbd5cf51f4f6e5ff8",
    "visual_review": "All eight PDF pages inspected; local rail collisions and rotated passive labels corrected; motor output and mask blocks separated; simple sheets compacted to A3; audio border kept above title block. Native schematics, not raster diagrams.",
    "revision_values": {
      "R70": {
        "value": "464k",
        "MPN": "RT0603BRD07464KL"
      },
      "R71": {
        "value": "100k",
        "MPN": "RT0603BRD07100KL"
      }
    },
    "scope": "Static pin-net and ERC validation only. Does not prove analogue design, firmware, PCB or physical operation."
  },
  "DRC_ignored_checks": [
    {
      "description": "Footprint has no courtyard defined",
      "key": "missing_courtyard"
    },
    {
      "description": "Track endpoint not centered on via",
      "key": "track_not_centered_on_via"
    },
    {
      "description": "Tuning profile track geometries",
      "key": "tuning_profile_track_geometries"
    },
    {
      "description": "Footprint doesn't match symbol's footprint filters",
      "key": "footprint_filters_mismatch"
    },
    {
      "description": "Footprint component type doesn't match footprint pads",
      "key": "footprint_type_mismatch"
    }
  ],
  "manufacturing_status": "Prototype design for review; not production approved. Controlled impedance, electrical tests, host firmware and hull integration remain to validate.",
  "mechanical_status": "Proposed suspended mounting under arm platform; native rover CAD and its attachments have NOT been modified",
  "bench_carrier_status": "Bench-only carrier. Excluded from the proposed rover integration because its underside would collide with the battery placeholder.",
  "portable_package_DRC": {
    "violations": 0,
    "unconnected_items": 0,
    "schematic_parity": 0
  },
  "final_design_sha256": {
    "MOSS_Core_V1C.kicad_pcb": "7f8bea271fe73fb781dc34ad7b6507380e59a6f29eeec05d8f588f6bedc5b244",
    "MOSS_Core_V1C.kicad_pro": "91ad0ba727457bd12038f267343eb08e33716c44c76c315b9a715583e948b5e6",
    "MOSS_Core_V1C.kicad_dru": "24d5714c192048681f6bb66839684cd4042558bf9704974d9b65c58213ef0796",
    "01_USB_Power.kicad_sch": "9f201886137ca4cdb1e13916210c4ca38465a7ab7afd5967d6f1d377e827b713",
    "04_Drive_Encoders.kicad_sch": "460a70370a1127d7dcf0d9e77b45e09a2b84ae3d405262bd6b5b38a19575bb85",
    "05_Servo.kicad_sch": "5cc31d71cee329c42503d7d3806b139c5568e6434cff9cc56efba1e81e919f64",
    "03_Hardware_Interlock.kicad_sch": "6ee9b8f470de30aa662cf141ddbe0d5497dec66ba247c2306196f02953ea9b18",
    "07_Current_Sense.kicad_sch": "a2333f5b9dac8e4f0e0d226a85b94c25dec94b436586573cbe71d9efbae339b1",
    "06_Audio.kicad_sch": "41c500f9eecbeec69ced529ca7909184f82e3999658b9d75645fd484b7f46c30",
    "02_Controller.kicad_sch": "01b4afa0cb70a8a28207dd4fb02fcca844a30c19d38b431f1c8e49206cc1a7fc",
    "MOSS_Core_V1C.kicad_sch": "a79132372a7874c866d742643a52ef6c87ef0d133912c6678e77ea2ca4b99909"
  },
  "final_export_identity_matches_checked_working_project": true,
  "local_3D_models_resolved": 27,
  "publication_language": "en",
  "language_review": "LANGUAGE_REVIEW.json",
  "publication_note": "English documentation correction only. Electrical design and fabrication outputs unchanged."
}