Skip to content

armgit / moss

Public Imported from GitHub
0

MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.

Python

README rewritten for the reader; print set complete (113 parts), hardware in; order and delivery status removed from the docs

metrox0cef8b9629c0
diff --git a/README.md b/README.md
index 44ecd9b..d75dac6 100644
--- a/README.md
+++ b/README.md
@@ -2,45 +2,38 @@
Cleaner streets, one maker at a time.
-MOSS is a small, mostly 3D-printed litter-picking rover: tracked base, a collection bin, and an arm derived from the SO-101 with a NormaCore parallel gripper. Target parts cost: 500 to 700 USD plus a Jetson (before tax and shipping, labour and tools excluded). The goal is a design any maker can print, build, improve, and run where they live.
+MOSS is a small litter-picking rover you can print and build yourself: a tracked base, a bin, and an arm derived from the SO-101 with a parallel gripper. About 500 to 700 USD in parts, plus a Jetson. It is being built in public, from a living room in Hua Hin, Thailand. Nothing here is finished; everything here is real.
![MOSS exploded view, turntable](media/images/moss_exploded_turntable.gif)
-This repository is the build log, the design files as they become real, and the software as it gets written. It started on 15 September 2026. Nothing here is finished; everything here is real. The animation above is a CAD visualization from 18 September (the V0.3 exterior, exploded and assembled); newer cover studies are not the physical prototype. The photo below is the bench on 20 September: the power and control harness wired for the first motor tests. The concept video from 15 September (V2.3.1) shows an earlier design: almost everything changed since.
+## Where it stands
-![Power and control harness on the bench, 20 September](media/images/build_harness_bench_20260920.jpg)
+All 113 printed parts are on the bench, with the shafts, bearings and screws to go with them. On 20 September the two drive motors ran for the first time, encoders counting, from the ESP32 that will drive them on the rover. That is the whole story so far: it runs on the bench, it does not roll yet. Next is putting the harness inside the chassis and making it drive.
-## Status — V0.3 prototype, 20 September 2026
+![The power and control harness on the bench, 20 September](media/images/build_harness_bench_20260920.jpg)
-- Printing is reported essentially complete for the chassis, bin and cover, track structure, wheels and rollers, tensioners, spacers, interior supports, the SO-101-derived arm and the NC90 gripper. See the [printed-parts inventory](docs/printed_parts.md): 111 pieces in the reconciled print set, plus two camera brackets to confirm.
-- One TPU 95A track printed with a 0.8 mm nozzle is too stiff and will be reprinted. The first track has good flexibility and grip in manual floor tests.
-- Assembly and fit checks continue. The corrected motor-bracket revision and the two RealSense mounting brackets still have to be confirmed on the bench before the print set is called fully reconciled.
-- The unfinished front-cover interface stays on this prototype; its redesign is deferred to the next hardware revision.
-- 20 September: the power and control harness is assembled and was bench-tested. Both drive motors and their quadrature encoders ran from an Espressif ESP32-S3-DevKitC-1 through two Cytron MD10C R3 drivers: 15 % single-motor tests, then one 0–100 % PWM ramp cycle in each direction, then the 25 % commissioning limit was restored. Unloaded, on the bench; commanded and timed stops observed. No rover roll, no loaded or stall test. Details, numbers and limits in the [build log](docs/build_log.md#2026-09-20--power-and-control-harness-first-motor-and-encoder-tests); video: [MOSS_motor_encoder_bench_20260920.mp4](media/video/MOSS_motor_encoder_bench_20260920.mp4).
-- Electronics as selected now: Jetson Orin Nano 8 GB (in its original plastic base, inside the printed cartridge), Intel RealSense depth camera (IMU inside), ESP32-S3-DevKitC-1 V1.1 as motor controller, 2 × Cytron MD10C R3, 2 × geared motors with encoders, a separate Waveshare Bus Servo Adapter (A) V1.1 for the arm servos (arm not tested yet), an INA219 module used for battery voltage only, fuse holder and positive distribution block. The Waveshare General Driver for Robots is no longer part of the design.
-- Ordered: steel shafts (5/6/8 mm), bearings (608, 626), shaft collars, 6 mm couplings, M3 and M4 fasteners.
-- Software: the ESP32-S3 commissioning firmware in [`firmware/`](firmware/README.md) (serial commands, disarmed at boot, 300 ms command watchdog, 25 % limit, encoder and voltage telemetry; host logic test passes). On the Jetson side, a scaffold (gamepad teleop logic and differential-drive kinematics, cold-tested, not yet run on the rover). No speed control, no odometry, no drive test on the ground, no autonomous pickup yet.
-- Next: integrate the harness into the chassis, set forward direction and encoder signs after the mirrored installation, measure ticks per revolution, write the Jetson–ESP32 interface then speed control; replace the stiff track, assemble and check the drivetrain, fit the arm.
+Every step is written down when it is real, good or bad. The [build log](docs/build_log.md) has the dates and the numbers, the [assembly feedback](docs/assembly_feedback.md) has what did not fit, the [roadmap](docs/roadmap.md) has what comes next, without dates.
-## Demo
+## Try the demo
-A recorded-run 3D demo where Jev (TypeSafe AI's decision model) chooses which litter to pick up: https://www.showrobotics.ai/moss-jev/ (three real API responses, replayed; no live inference). Mirror: https://metrox-eth.github.io/moss-jev/ · Source: https://github.com/metrox-eth/moss-jev
+Jev, TypeSafe AI's decision model, choosing which piece of litter to go for, in 3D, on recorded runs: https://www.showrobotics.ai/moss-jev/
-## Data
+## What is in here
-Teleop data recorded by MOSS builders is meant to be pooled and open, so the shared model gets better with every robot. Details and the rules we propose are in [docs/data.md](docs/data.md).
+- `docs/` what MOSS is for, the build log, the bill of materials, the printed-parts list, the data rules, the roadmap.
+- `firmware/` the ESP32-S3 code that drives the motors, with its test.
+- `moss_dimos/` the Jetson side, on dimOS. Cold-tested only, for now.
+- `hardware/` the design files, published part by part as they prove themselves on the real robot, and the raw bench traces.
+- `media/` the videos and photos.
-## Layout
+## Build one, or come and watch
-- `docs/` concept, build log, bill of materials, data, roadmap, software notes.
-- `hardware/` design files (coming as parts are validated); `hardware/bench/` raw traces of the bench tests.
-- `firmware/` ESP32-S3 commissioning firmware, its host test and wiring map.
-- `moss_dimos/` software scaffold (dimOS modules).
-- `media/` videos and images of the concept and the build.
-- `tests/` cold tests (no hardware needed).
+The design files are not out yet. They come once the first MOSS rolls and the parts have earned it. Until then, the door is the Discord: ask anything, tell us what we are doing wrong, it helps the next builder too. https://discord.com/invite/x2MeNmgveT
+
+The build, day by day, is on X: [@metrox_eth](https://x.com/metrox_eth).
+
+Data recorded by MOSS builders is meant to be pooled and open, so the shared model gets better with every robot. The rules we propose are in [docs/data.md](docs/data.md).
## License
Code under Apache-2.0. Hardware files and documentation under CC BY 4.0. See `NOTICE`.
-
-Built in public by [@metrox_eth](https://x.com/metrox_eth).
diff --git a/docs/assembly_feedback.md b/docs/assembly_feedback.md
index 90264c8..712b516 100644
--- a/docs/assembly_feedback.md
+++ b/docs/assembly_feedback.md
@@ -4,11 +4,11 @@ One line per finding: what was observed, which part and revision, what was done
| Finding | Part / revision | On the prototype | Next revision | Validation done |
|---|---|---|---|---|
-| TPU track too stiff | Track printed with a 0.8 mm nozzle | Reprint planned; keep the 0.4 mm profile (nozzle, extrusion width, walls, layer height, infill, material) as the reference | Record the full print profile with the part | First track: manual floor test, good flexibility and grip |
-| Motor mounts | Corrected brackets Ø31 / M3 (files marked V2-01) | Confirm the corrected pair is the one fitted; check screw depth | — | Not yet |
+| TPU track too stiff | Track printed with a 0.8 mm nozzle | Not used; the 0.4 mm profile (nozzle, extrusion width, walls, layer height, infill, material) is the reference | Record the full print profile with the part | 0.4 mm track: manual floor test, good flexibility and grip |
+| Motor mounts | Corrected brackets Ø31 / M3 (files marked V2-01) | Check screw depth at assembly | — | Not yet |
| Motor mount to hull joint | Through-hole planned on the prototype | Drill through | Real through-joint designed in | Not yet |
| Front of the cover and offset arm plate | Cover, arm plate | Keep the unfinished interface as is | Complete-cover study, parked | — |
-| Camera brackets | Two RealSense brackets in the CAD export | Locate or print them | — | Not found in the final numbered plates |
+| Camera brackets | Two RealSense D455 brackets | Fit at assembly | — | Not yet |
| Plate gasket | R8 gasket listed with the R11 plate | Check the real fit at assembly | — | Not yet |
| No mounts for the selected electronics | ESP32-S3-DevKitC-1, Bus Servo Adapter, distribution block, fuse holder (20 September architecture) | Fix in place as possible for the first tests | Design the mounts in | Harness bench-tested outside the chassis |
| INA219 cannot sit in the motor line | INA219 module terminal vs main cable | Voltage monitoring only; current path bypasses the shunt | Proper current sensing if wanted | I²C and voltage read confirmed; current readings invalid |
diff --git a/docs/bom.md b/docs/bom.md
index b33ab3e..e78c85a 100644
--- a/docs/bom.md
+++ b/docs/bom.md
@@ -4,15 +4,15 @@ Target: 500 to 700 USD in parts plus a Jetson, before tax and shipping. Prices a
## Printed parts
-The authoritative list is the [printed-parts inventory](printed_parts.md) (111 pieces in the reconciled V0.3 print set, per-part material, source file, print job and status; machine-readable copy in `printed_parts.json`). Summary by assembly:
+The authoritative list is the [printed-parts inventory](printed_parts.md) (113 pieces in the V0.3 print set, per-part material, source file and print job; machine-readable copy in `printed_parts.json`). Summary by assembly:
| Assembly | Printed pieces | Notes |
|---|---:|---|
| Body (chassis, motor hatch, bin, cover) | 4 | chassis black PETG (H2S), bin and cover PLA |
-| Tracks | 2 | TPU 95A; the 0.8 mm-nozzle track is too stiff, reprint planned |
+| Tracks | 2 | TPU 95A, 0.4 mm nozzle profile (a 0.8 mm-nozzle print came out too stiff) |
| Side structure (inner and outer rails, cross spacers) | 8 | PETG |
| Ventilation (splash-proof vent covers) | 2 | PETG |
-| Motor mounts | 2 | corrected revision to confirm on the bench |
+| Motor mounts | 2 | corrected revision Ø31 / M3 |
| Wheels and rollers | 20 | 2 drive wheels (4 halves), 2 idlers (4 halves), 6 road rollers (12 halves) |
| Tensioners and bearing retainers | 12 | |
| Drivetrain spacers | 32 | small spacers, distinct from the 4 cross spacers |
@@ -21,7 +21,8 @@ The authoritative list is the [printed-parts inventory](printed_parts.md) (111 p
| SO-101-derived arm | 8 | clips integrated in the arm parts |
| NC90 gripper (derived from the NormaCore parallel gripper) | 8 | rigid parts |
| Gripper pads | 2 | TPU |
-| **Total** | **111** | plus 2 RealSense brackets, printing to confirm |
+| Camera brackets | 2 | RealSense D455 |
+| **Total** | **113** | |
Not printed: metal HEX12 hubs, bearings, shaft collars, motor–shaft couplings, servo horns, fasteners.
@@ -33,7 +34,7 @@ Not printed: metal HEX12 hubs, bearings, shaft collars, motor–shaft couplings,
- 2 × geared DC motors with quadrature encoders
- Waveshare Bus Servo Adapter (A) V1.1: separate interface for the SO-101 arm servos (arm not tested yet)
- INA219 module at 0x40 (R100 = 0.1 Ω shunt): used for battery voltage only. In the tested wiring the motor current bypasses the shunt, so its current readings are not motor consumption. See the build log.
-- Fuse holder with automotive blade fuse. Provisional rating for motor bench tests: 5 A, 32 V DC (decided; installation not confirmed). Not the final rating for the complete rover with Jetson and arm; the pack's BMS thresholds are unknown.
+- Fuse holder with automotive blade fuse, 5 A (32 V DC) for the motor bench tests. The rating for the complete rover with Jetson and arm is not set yet; the pack's BMS thresholds are unknown.
- Positive distribution terminal block with ferrules; negative returns chained; XT60 to the pack
- 5 V buck converter for the logic, if needed (not installed)
- Removed from the design: Waveshare General Driver for Robots.
@@ -51,4 +52,4 @@ Cabling: same wire for the main runs and the driver branches, runs of 25–30 cm
- SO-101 derived arm (6 DoF)
- NormaCore parallel gripper
-![Hardware ordered](../media/images/build_05_hardware_ordered_20260917.jpg)
+![Mechanical hardware](../media/images/build_05_hardware_ordered_20260917.jpg)
diff --git a/docs/build_log.md b/docs/build_log.md
index b5a92c5..88540fe 100644
--- a/docs/build_log.md
+++ b/docs/build_log.md
@@ -48,7 +48,7 @@ Next: replace the stiff track, assemble and check the drivetrain, fit the arm an
## 2026-09-20 — power and control harness, first motor and encoder tests
-The power and control harness is assembled. Both drive motors and their quadrature encoders were tested on the bench from an Espressif ESP32-S3-DevKitC-1 V1.1 driving two Cytron MD10C R3. Video: [MOSS_motor_encoder_bench_20260920.mp4](../media/video/MOSS_motor_encoder_bench_20260920.mp4); photo: [the harness on the bench](../media/images/build_harness_bench_20260920.jpg).
+The print set is complete, camera brackets and corrected motor brackets included, and the mechanical hardware (shafts, bearings, collars, couplings, fasteners) is in. The power and control harness is assembled. Both drive motors and their quadrature encoders were tested on the bench from an Espressif ESP32-S3-DevKitC-1 V1.1 driving two Cytron MD10C R3. Video: [MOSS_motor_encoder_bench_20260920.mp4](../media/video/MOSS_motor_encoder_bench_20260920.mp4); photo: [the harness on the bench](../media/images/build_harness_bench_20260920.jpg).
The selected architecture now uses the ESP32-S3 as motor controller and a separate Waveshare Bus Servo Adapter (A) V1.1 for the SO-101 arm servos. The Waveshare General Driver for Robots is no longer part of the design. The arm was not tested in this session. The ESP32 was powered over USB-UART during the tests; the motors from the pack through the fuse and the positive distribution block, with common grounds.
@@ -72,7 +72,7 @@ INA219 communication at 0x40 works and the pack read around 11.95–11.97 V: a v
### Protection and cabling
-Provisional fuse for motor bench tests: 5 A automotive blade, 32 V DC, same format as the holder. Decided, ordered; installation not confirmed. This is not the final rating for the rover with Jetson and arm; the pack's BMS thresholds are unknown. Cable runs of 25–30 cm at most; conductor bundle measured 1.2 mm in diameter, section estimated at 0.75–1 mm², not verified.
+Fuse for the motor bench tests: 5 A automotive blade, 32 V DC, same format as the holder. This is not the final rating for the rover with Jetson and arm; the pack's BMS thresholds are unknown. Cable runs of 25–30 cm at most; conductor bundle measured 1.2 mm in diameter, section estimated at 0.75–1 mm², not verified.
Next: integrate the harness into the chassis, set installed motor and encoder directions, measure ticks per revolution, then the Jetson interface and speed control. For the next hardware revision: mounts for the ESP32-S3, the servo adapter and the real distribution; the printed V0.3 stays the reference.
diff --git a/docs/printed_parts.json b/docs/printed_parts.json
index 848f6b9..e126e68 100644
--- a/docs/printed_parts.json
+++ b/docs/printed_parts.json
@@ -1,10 +1,8 @@
{
- "as_of": "2026-09-19",
+ "as_of": "2026-09-20",
"repository": "https://github.com/metrox-eth/moss",
"reviewed_commit": "d22c513c2d5f866f8da212f4962d24a594859de1",
- "basis": "Builder reports that printing appears complete except one track replacement. Quantities reconstructed from delivered final print plans, not independently counted on the bench.",
- "expected_printed_units_in_reconciled_plan": 111,
- "additional_camera_brackets_to_reconcile": 2,
+ "basis": "Print set complete per the builder on 20 September 2026. Quantities reconstructed from the final print plans.",
"parts": [
{
"group": "Body",
@@ -13,7 +11,7 @@
"material": "Black PETG",
"source_file": "Carter_PETG_continu_-_revision_mecanique_R8.stl",
"print_job": "Standalone H2S chassis",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -23,7 +21,7 @@
"material": "Black PETG",
"source_file": "Trappe_inferieure_acces_moteurs_R8.stl",
"print_job": "Standalone hatch",
- "status": "reported_printed",
+ "status": "printed",
"note": "R8 export reference; the precise revision of the physical hatch is not recorded."
},
{
@@ -33,7 +31,7 @@
"material": "Blue PLA",
"source_file": "MOSS_bac_corrige.stl",
"print_job": "Standalone H2S bin",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -43,7 +41,7 @@
"material": "Blue PLA",
"source_file": "MOSS_capot_monobloc_H2S_R5.stl",
"print_job": "Standalone H2S cover",
- "status": "reported_printed",
+ "status": "printed",
"note": "Keep the printed prototype cover. The unfinished front interface remains as-is; full-cover redesign is parked."
},
{
@@ -52,9 +50,9 @@
"quantity": 2,
"material": "TPU 95A",
"source_file": "MOSS_chenille_TPU95A_P1S_R2.stl",
- "print_job": "Standalone P1S tracks",
- "status": "one_accepted_one_reprint_planned",
- "note": "Two tracks have been printed. The first was reported flexible with good grip; the track printed with a 0.8 mm nozzle is too stiff and will be reprinted. Replacement has not been reported complete."
+ "print_job": "Standalone P1S tracks, 0.4 mm nozzle",
+ "status": "printed",
+ "note": "A print made with a 0.8 mm nozzle came out too stiff and is not used; the 0.4 mm profile is the reference."
},
{
"group": "Side structure",
@@ -63,7 +61,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_traverse_-40_R8.stl",
"print_job": "01 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -73,7 +71,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_traverse_40_R8.stl",
"print_job": "01 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -83,7 +81,7 @@
"material": "Black PETG",
"source_file": "R8_G_Flanc_interieur_R8.stl",
"print_job": "01 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -93,7 +91,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_traverse_-40_R8.stl",
"print_job": "01 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -103,7 +101,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_traverse_40_R8.stl",
"print_job": "01 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -113,7 +111,7 @@
"material": "Black PETG",
"source_file": "R8_D_Flanc_interieur_R8.stl",
"print_job": "01 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -123,7 +121,7 @@
"material": "Black PETG",
"source_file": "R8_G_Flanc_exterieur_R8.stl",
"print_job": "02 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -133,7 +131,7 @@
"material": "Black PETG",
"source_file": "R8_D_Flanc_exterieur_R8.stl",
"print_job": "03 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -143,7 +141,7 @@
"material": "Black PETG",
"source_file": "Entree_air_sous_carter_-_chicane_demontable_R8.stl",
"print_job": "03 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -153,7 +151,7 @@
"material": "Black PETG",
"source_file": "Extraction_air_sous_carter_-_chicane_demontable_R8.stl",
"print_job": "03 — P1S 0.8",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -163,8 +161,8 @@
"material": "Black PETG",
"source_file": "MOSS_support_moteur_G_V2_01.stl",
"print_job": "Standalone correction — P1S 0.4",
- "status": "physical_revision_to_confirm",
- "note": "Replaces the original plate-02 bracket; count once in the current build. Confirm the physical part is the corrected Ø31 mm M3 pattern, not the original bracket. Fit is not yet individually signed off."
+ "status": "printed",
+ "note": "Replaces the original plate-02 bracket; count once in the current build. Corrected Ø31 mm / M3 pattern; screw depth to check at assembly."
},
{
"group": "Motor mounts",
@@ -173,8 +171,8 @@
"material": "Black PETG",
"source_file": "MOSS_support_moteur_D_V2_01.stl",
"print_job": "Standalone correction — P1S 0.4",
- "status": "physical_revision_to_confirm",
- "note": "Replaces the original plate-02 bracket; count once in the current build. Confirm the physical part is the corrected Ø31 mm M3 pattern, not the original bracket. Fit is not yet individually signed off."
+ "status": "printed",
+ "note": "Replaces the original plate-02 bracket; count once in the current build. Corrected Ø31 mm / M3 pattern; screw depth to check at assembly."
},
{
"group": "Wheels and rollers",
@@ -183,7 +181,7 @@
"material": "Black PETG",
"source_file": "R8_D_Roue_tendeuse_22d_demi-exterieure_R8.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -193,7 +191,7 @@
"material": "Black PETG",
"source_file": "R8_D_Roue_tendeuse_22d_demi-interieure_R8.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -203,7 +201,7 @@
"material": "Black PETG",
"source_file": "R8_G_Roue_tendeuse_22d_demi-exterieure_R8.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -213,7 +211,7 @@
"material": "Black PETG",
"source_file": "R8_G_Roue_tendeuse_22d_demi-interieure_R8.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -223,7 +221,7 @@
"material": "Black PETG",
"source_file": "R8H_D_Roue_motrice_HEX12_demi_exterieure.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -233,7 +231,7 @@
"material": "Black PETG",
"source_file": "R8H_D_Roue_motrice_HEX12_demi_interieure.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -243,7 +241,7 @@
"material": "Black PETG",
"source_file": "R8H_G_Roue_motrice_HEX12_demi_exterieure.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -253,7 +251,7 @@
"material": "Black PETG",
"source_file": "R8H_G_Roue_motrice_HEX12_demi_interieure.stl",
"print_job": "04A — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -263,7 +261,7 @@
"material": "Black PETG",
"source_file": "R8_D_Galet625_-70_demi-exterieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -273,7 +271,7 @@
"material": "Black PETG",
"source_file": "R8_D_Galet625_-70_demi-interieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -283,7 +281,7 @@
"material": "Black PETG",
"source_file": "R8_D_Galet625_0_demi-exterieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -293,7 +291,7 @@
"material": "Black PETG",
"source_file": "R8_D_Galet625_0_demi-interieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -303,7 +301,7 @@
"material": "Black PETG",
"source_file": "R8_D_Galet625_70_demi-exterieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -313,7 +311,7 @@
"material": "Black PETG",
"source_file": "R8_D_Galet625_70_demi-interieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -323,7 +321,7 @@
"material": "Black PETG",
"source_file": "R8_G_Galet625_-70_demi-exterieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -333,7 +331,7 @@
"material": "Black PETG",
"source_file": "R8_G_Galet625_-70_demi-interieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -343,7 +341,7 @@
"material": "Black PETG",
"source_file": "R8_G_Galet625_0_demi-exterieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -353,7 +351,7 @@
"material": "Black PETG",
"source_file": "R8_G_Galet625_0_demi-interieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -363,7 +361,7 @@
"material": "Black PETG",
"source_file": "R8_G_Galet625_70_demi-exterieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -373,7 +371,7 @@
"material": "Black PETG",
"source_file": "R8_G_Galet625_70_demi-interieure_R8.stl",
"print_job": "04B — P1S 0.4; replaces 04 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -383,7 +381,7 @@
"material": "Black PETG",
"source_file": "R8_D_Couvercle_tendeur_exterieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -393,7 +391,7 @@
"material": "Black PETG",
"source_file": "R8_D_Couvercle_tendeur_interieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -403,7 +401,7 @@
"material": "Black PETG",
"source_file": "R8_G_Couvercle_tendeur_exterieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -413,7 +411,7 @@
"material": "Black PETG",
"source_file": "R8_G_Couvercle_tendeur_interieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -423,7 +421,7 @@
"material": "Black PETG",
"source_file": "R8_D_Coulisseau_exterieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -433,7 +431,7 @@
"material": "Black PETG",
"source_file": "R8_D_Coulisseau_interieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -443,7 +441,7 @@
"material": "Black PETG",
"source_file": "R8_G_Coulisseau_exterieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -453,7 +451,7 @@
"material": "Black PETG",
"source_file": "R8_G_Coulisseau_interieur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -463,7 +461,7 @@
"material": "Black PETG",
"source_file": "R8_D_Couvercle_palier_moteur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -473,7 +471,7 @@
"material": "Black PETG",
"source_file": "R8_G_Couvercle_palier_moteur_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -483,7 +481,7 @@
"material": "Black PETG",
"source_file": "Retenue_interieure_roulement_-1_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -493,7 +491,7 @@
"material": "Black PETG",
"source_file": "Retenue_interieure_roulement_1_R8.stl",
"print_job": "05 — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -503,7 +501,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_-70_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -513,7 +511,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_-70_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -523,7 +521,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_-70_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -533,7 +531,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_0_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -543,7 +541,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_0_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -553,7 +551,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_0_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -563,7 +561,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_70_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -573,7 +571,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_70_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -583,7 +581,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_galet_70_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -593,7 +591,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_tendeur_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -603,7 +601,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_tendeur_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -613,7 +611,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_tendeur_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -623,7 +621,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_tendeur_retenue_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -633,7 +631,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_tendeur_retenue_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -643,7 +641,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_-70_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -653,7 +651,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_-70_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -663,7 +661,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_-70_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -673,7 +671,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_0_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -683,7 +681,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_0_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -693,7 +691,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_0_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -703,7 +701,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_70_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -713,7 +711,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_70_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -723,7 +721,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_galet_70_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -733,7 +731,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_tendeur_centrale_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -743,7 +741,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_tendeur_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -753,7 +751,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_tendeur_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -763,7 +761,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_tendeur_retenue_externe_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -773,7 +771,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_tendeur_retenue_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -783,7 +781,7 @@
"material": "Black PETG",
"source_file": "R8_D_Entretoise_motrice_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -793,7 +791,7 @@
"material": "Black PETG",
"source_file": "R8_G_Entretoise_motrice_interne_R8.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -803,7 +801,7 @@
"material": "Black PETG",
"source_file": "R8H_D_Entretoise_motrice_externe_HEX12_L15_6.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -813,7 +811,7 @@
"material": "Black PETG",
"source_file": "R8H_G_Entretoise_motrice_externe_HEX12_L15_6.stl",
"print_job": "06 — P1S 0.4; replaces 06 H2S",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -823,7 +821,7 @@
"material": "TPU 95A",
"source_file": "Joint_trappe_moteurs_R8.stl",
"print_job": "07 joints — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": "R8 gasket source; fit to assembled interfaces remains to be checked."
},
{
@@ -833,7 +831,7 @@
"material": "TPU 95A",
"source_file": "Joint_sous_platine_-_appui_continu_R8.stl",
"print_job": "07 joints — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": "R8 gasket source; fit to assembled interfaces remains to be checked."
},
{
@@ -843,7 +841,7 @@
"material": "TPU 95A",
"source_file": "R8_CAMERA_Joint_facade_D455_R8.stl",
"print_job": "07 joints — H2S 0.4",
- "status": "reported_printed",
+ "status": "printed",
"note": "R8 gasket source; fit to assembled interfaces remains to be checked."
},
{
@@ -853,7 +851,7 @@
"material": "Black PLA",
"source_file": "Berceau_electronique_R11.stl",
"print_job": "07A_berceau_PLA_noir",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -863,7 +861,7 @@
"material": "Black PLA",
"source_file": "Support_porte_fusible_R9.stl",
"print_job": "07A_berceau_PLA_noir",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -873,7 +871,7 @@
"material": "Black PLA",
"source_file": "Platine_bras_R11.stl",
"print_job": "07B_platine_PLA_noir",
- "status": "reported_printed",
+ "status": "printed",
"note": "Replacement arm plate, not an additional plate stacked on top of R8/R9."
},
{
@@ -883,7 +881,7 @@
"material": "Black PLA",
"source_file": "Retenue_socle_Jetson_R11.stl",
"print_job": "07B_platine_PLA_noir",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -893,7 +891,7 @@
"material": "Black PLA",
"source_file": "Plateau_Jetson_R11.stl",
"print_job": "07C_Jetson_PLA_noir",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -903,7 +901,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Bras_superieur_clip.stl",
"print_job": "08_bras_PLA_saumon_01",
- "status": "reported_printed",
+ "status": "printed",
"note": "Four cable clips are integrated into arm parts; no additional printed clip count."
},
{
@@ -913,7 +911,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Avant_bras_clip.stl",
"print_job": "08_bras_PLA_saumon_01",
- "status": "reported_printed",
+ "status": "printed",
"note": "Four cable clips are integrated into arm parts; no additional printed clip count."
},
{
@@ -923,7 +921,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Base.stl",
"print_job": "08_bras_PLA_saumon_01",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -933,7 +931,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Rotation_epaule.stl",
"print_job": "08_bras_PLA_saumon_01",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -943,7 +941,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Support_epaule_clip.stl",
"print_job": "08_bras_PLA_saumon_01",
- "status": "reported_printed",
+ "status": "printed",
"note": "Four cable clips are integrated into arm parts; no additional printed clip count."
},
{
@@ -953,7 +951,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Base_motor_holder.stl",
"print_job": "08_bras_PLA_saumon_02",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -963,7 +961,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Poignet_clip.stl",
"print_job": "08_bras_PLA_saumon_02",
- "status": "reported_printed",
+ "status": "printed",
"note": "Four cable clips are integrated into arm parts; no additional printed clip count."
},
{
@@ -973,7 +971,7 @@
"material": "PLA — salmon in print plan",
"source_file": "SO101_Support_poignet.stl",
"print_job": "08_bras_PLA_saumon_02",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -983,7 +981,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Corps_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -993,7 +991,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Machoire_gauche_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1003,7 +1001,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Machoire_droite_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1013,7 +1011,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Support_camera_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1023,7 +1021,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Flasque_1_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1033,7 +1031,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Flasque_2_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1043,7 +1041,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Pignon_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1053,7 +1051,7 @@
"material": "PLA — turquoise in print plan",
"source_file": "Guide_cable_NC90.stl",
"print_job": "09_pince_PLA_turquoise",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1063,7 +1061,7 @@
"material": "TPU 95A",
"source_file": "Patin_TPU_gauche.stl",
"print_job": "10_patins_TPU95A",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
},
{
@@ -1073,28 +1071,31 @@
"material": "TPU 95A",
"source_file": "Patin_TPU_droit.stl",
"print_job": "10_patins_TPU95A",
- "status": "reported_printed",
+ "status": "printed",
"note": ""
- }
- ],
- "unconfirmed_additional_parts": [
+ },
{
+ "group": "Camera brackets",
"part": "D455 camera mounting bracket -1",
"quantity": 1,
- "material": "PETG in original plan",
+ "material": "PETG",
"source_file": "R8_CAMERA_Equerre_D455_-1_R8.stl",
- "status": "printing_not_confirmed",
- "note": "Present in R8 CAD/STLs, not located in the final numbered print plates. Check the bench before adding a print job."
+ "print_job": "Standalone",
+ "status": "printed",
+ "note": "RealSense D455 mounting bracket."
},
{
+ "group": "Camera brackets",
"part": "D455 camera mounting bracket 1",
"quantity": 1,
- "material": "PETG in original plan",
+ "material": "PETG",
"source_file": "R8_CAMERA_Equerre_D455_1_R8.stl",
- "status": "printing_not_confirmed",
- "note": "Present in R8 CAD/STLs, not located in the final numbered print plates. Check the bench before adding a print job."
+ "print_job": "Standalone",
+ "status": "printed",
+ "note": "RealSense D455 mounting bracket."
}
],
"scope": "Prototype inventory only. No CAD/STL release approval or physical fit certification. Duplicate formats, superseded plates and failed/rejected designs excluded.",
- "prototype_version": "V0.3"
+ "prototype_version": "V0.3",
+ "printed_units": 113
}
diff --git a/docs/printed_parts.md b/docs/printed_parts.md
index 3172c64..471387c 100644
--- a/docs/printed_parts.md
+++ b/docs/printed_parts.md
@@ -1,15 +1,14 @@
# MOSS V0.3 — prototype printed-parts inventory
-Updated: **19 September 2026**.
+Updated: **20 September 2026**.
-The builder reports that printing appears complete, with one track to reprint. This inventory reconciles the final delivered print plans: **111 pieces in the intended current print set**, plus **two camera brackets whose printing is not confirmed**. It is not an independent physical count. Quantities are assembly requirements, not the cumulative number of prints, failed attempts or spares.
+The V0.3 print set is complete: **113 pieces**, reconciled from the final print plans. Quantities are assembly requirements, not the cumulative number of prints, failed attempts or spares.
-`reported_printed` follows that overall build update; it does not mean every part has been fitted or load-tested. The corrected motor-bracket revision still needs identification on the bench. The 0.8 mm track remains a replacement task.
+`printed` means the part exists; fit and load checks happen at assembly and are logged in [assembly_feedback.md](assembly_feedback.md).
## Current print feedback
-- Two TPU 95A tracks have been printed. The first track was reported to have good flexibility and floor grip.
-- The track made with the 0.8 mm nozzle is too stiff and is scheduled for reprinting; completion is not yet reported.
+- Tracks in TPU 95A: the 0.4 mm-nozzle print has good flexibility and floor grip in a manual test. A print made with a 0.8 mm nozzle came out too stiff and is not used.
- Preserve the successful 0.4 mm print profile as the reference. Record nozzle, extrusion width, walls, layer height, infill and material together; the two prints do not isolate nozzle diameter as the only cause.
- The prototype front cover remains unfinished around the offset arm plate. The complete-cover redesign is parked for the next hardware revision and is excluded below.
@@ -42,10 +41,10 @@ G/D and −1/+1 retain the CAD naming so parts can be matched to their source fi
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `Carter_PETG_continu_-_revision_mecanique_R8.stl` | 1 | Black PETG | Standalone H2S chassis | reported_printed |
-| `Trappe_inferieure_acces_moteurs_R8.stl` | 1 | Black PETG | Standalone hatch | reported_printed |
-| `MOSS_bac_corrige.stl` | 1 | Blue PLA | Standalone H2S bin | reported_printed |
-| `MOSS_capot_monobloc_H2S_R5.stl` | 1 | Blue PLA | Standalone H2S cover | reported_printed |
+| `Carter_PETG_continu_-_revision_mecanique_R8.stl` | 1 | Black PETG | Standalone H2S chassis | printed |
+| `Trappe_inferieure_acces_moteurs_R8.stl` | 1 | Black PETG | Standalone hatch | printed |
+| `MOSS_bac_corrige.stl` | 1 | Blue PLA | Standalone H2S bin | printed |
+| `MOSS_capot_monobloc_H2S_R5.stl` | 1 | Blue PLA | Standalone H2S cover | printed |
- R8 export reference; the precise revision of the physical hatch is not recorded.
- Keep the printed prototype cover. The unfinished front interface remains as-is; full-cover redesign is parked.
@@ -54,125 +53,125 @@ G/D and −1/+1 retain the CAD naming so parts can be matched to their source fi
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `MOSS_chenille_TPU95A_P1S_R2.stl` | 2 | TPU 95A | Standalone P1S tracks | one_accepted_one_reprint_planned |
+| `MOSS_chenille_TPU95A_P1S_R2.stl` | 2 | TPU 95A | Standalone P1S tracks, 0.4 mm nozzle | printed |
-- Two tracks have been printed. The first was reported flexible with good grip; the track printed with a 0.8 mm nozzle is too stiff and will be reprinted. Replacement has not been reported complete.
+- A track printed with a 0.8 mm nozzle came out too stiff and is not used; the 0.4 mm profile is the reference.
### Side structure
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `R8_G_Entretoise_traverse_-40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | reported_printed |
-| `R8_G_Entretoise_traverse_40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | reported_printed |
-| `R8_G_Flanc_interieur_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | reported_printed |
-| `R8_D_Entretoise_traverse_-40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | reported_printed |
-| `R8_D_Entretoise_traverse_40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | reported_printed |
-| `R8_D_Flanc_interieur_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | reported_printed |
-| `R8_G_Flanc_exterieur_R8.stl` | 1 | Black PETG | 02 — P1S 0.8 | reported_printed |
-| `R8_D_Flanc_exterieur_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | reported_printed |
+| `R8_G_Entretoise_traverse_-40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |
+| `R8_G_Entretoise_traverse_40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |
+| `R8_G_Flanc_interieur_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |
+| `R8_D_Entretoise_traverse_-40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |
+| `R8_D_Entretoise_traverse_40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |
+| `R8_D_Flanc_interieur_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |
+| `R8_G_Flanc_exterieur_R8.stl` | 1 | Black PETG | 02 — P1S 0.8 | printed |
+| `R8_D_Flanc_exterieur_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | printed |
### Ventilation
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `Entree_air_sous_carter_-_chicane_demontable_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | reported_printed |
-| `Extraction_air_sous_carter_-_chicane_demontable_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | reported_printed |
+| `Entree_air_sous_carter_-_chicane_demontable_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | printed |
+| `Extraction_air_sous_carter_-_chicane_demontable_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | printed |
### Motor mounts
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `MOSS_support_moteur_G_V2_01.stl` | 1 | Black PETG | Standalone correction — P1S 0.4 | physical_revision_to_confirm |
-| `MOSS_support_moteur_D_V2_01.stl` | 1 | Black PETG | Standalone correction — P1S 0.4 | physical_revision_to_confirm |
+| `MOSS_support_moteur_G_V2_01.stl` | 1 | Black PETG | Standalone correction — P1S 0.4 | printed |
+| `MOSS_support_moteur_D_V2_01.stl` | 1 | Black PETG | Standalone correction — P1S 0.4 | printed |
-- Replaces the original plate-02 bracket; count once in the current build. Confirm the physical part is the corrected Ø31 mm M3 pattern, not the original bracket. Fit is not yet individually signed off.
+- Replaces the original plate-02 bracket; count once in the current build. Corrected Ø31 mm / M3 pattern; screw depth to check at assembly.
### Wheels and rollers
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `R8_D_Roue_tendeuse_22d_demi-exterieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Roue_tendeuse_22d_demi-interieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Roue_tendeuse_22d_demi-exterieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Roue_tendeuse_22d_demi-interieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8H_D_Roue_motrice_HEX12_demi_exterieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8H_D_Roue_motrice_HEX12_demi_interieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8H_G_Roue_motrice_HEX12_demi_exterieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8H_G_Roue_motrice_HEX12_demi_interieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Galet625_-70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Galet625_-70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Galet625_0_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Galet625_0_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Galet625_70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_D_Galet625_70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Galet625_-70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Galet625_-70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Galet625_0_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Galet625_0_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Galet625_70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
-| `R8_G_Galet625_70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | reported_printed |
+| `R8_D_Roue_tendeuse_22d_demi-exterieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Roue_tendeuse_22d_demi-interieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Roue_tendeuse_22d_demi-exterieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Roue_tendeuse_22d_demi-interieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8H_D_Roue_motrice_HEX12_demi_exterieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8H_D_Roue_motrice_HEX12_demi_interieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8H_G_Roue_motrice_HEX12_demi_exterieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8H_G_Roue_motrice_HEX12_demi_interieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Galet625_-70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Galet625_-70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Galet625_0_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Galet625_0_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Galet625_70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_D_Galet625_70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Galet625_-70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Galet625_-70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Galet625_0_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Galet625_0_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Galet625_70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
+| `R8_G_Galet625_70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |
### Tensioners and bearing retainers
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `R8_D_Couvercle_tendeur_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_D_Couvercle_tendeur_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_G_Couvercle_tendeur_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_G_Couvercle_tendeur_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_D_Coulisseau_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_D_Coulisseau_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_G_Coulisseau_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_G_Coulisseau_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_D_Couvercle_palier_moteur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `R8_G_Couvercle_palier_moteur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `Retenue_interieure_roulement_-1_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
-| `Retenue_interieure_roulement_1_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | reported_printed |
+| `R8_D_Couvercle_tendeur_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_D_Couvercle_tendeur_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_G_Couvercle_tendeur_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_G_Couvercle_tendeur_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_D_Coulisseau_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_D_Coulisseau_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_G_Coulisseau_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_G_Coulisseau_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_D_Couvercle_palier_moteur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `R8_G_Couvercle_palier_moteur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `Retenue_interieure_roulement_-1_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
+| `Retenue_interieure_roulement_1_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |
### Drivetrain spacers
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `R8_D_Entretoise_galet_-70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_-70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_-70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_0_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_0_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_0_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_galet_70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_tendeur_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_tendeur_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_tendeur_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_tendeur_retenue_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_tendeur_retenue_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_-70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_-70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_-70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_0_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_0_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_0_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_galet_70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_tendeur_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_tendeur_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_tendeur_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_tendeur_retenue_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_tendeur_retenue_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_D_Entretoise_motrice_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8_G_Entretoise_motrice_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8H_D_Entretoise_motrice_externe_HEX12_L15_6.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
-| `R8H_G_Entretoise_motrice_externe_HEX12_L15_6.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | reported_printed |
+| `R8_D_Entretoise_galet_-70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_-70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_-70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_0_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_0_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_0_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_galet_70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_tendeur_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_tendeur_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_tendeur_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_tendeur_retenue_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_tendeur_retenue_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_-70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_-70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_-70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_0_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_0_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_0_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_galet_70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_tendeur_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_tendeur_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_tendeur_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_tendeur_retenue_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_tendeur_retenue_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_D_Entretoise_motrice_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8_G_Entretoise_motrice_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8H_D_Entretoise_motrice_externe_HEX12_L15_6.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
+| `R8H_G_Entretoise_motrice_externe_HEX12_L15_6.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |
### Gaskets
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `Joint_trappe_moteurs_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | reported_printed |
-| `Joint_sous_platine_-_appui_continu_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | reported_printed |
-| `R8_CAMERA_Joint_facade_D455_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | reported_printed |
+| `Joint_trappe_moteurs_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | printed |
+| `Joint_sous_platine_-_appui_continu_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | printed |
+| `R8_CAMERA_Joint_facade_D455_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | printed |
- R8 gasket source; fit to assembled interfaces remains to be checked.
@@ -180,11 +179,11 @@ G/D and −1/+1 retain the CAD naming so parts can be matched to their source fi
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `Berceau_electronique_R11.stl` | 1 | Black PLA | 07A_berceau_PLA_noir | reported_printed |
-| `Support_porte_fusible_R9.stl` | 1 | Black PLA | 07A_berceau_PLA_noir | reported_printed |
-| `Platine_bras_R11.stl` | 1 | Black PLA | 07B_platine_PLA_noir | reported_printed |
-| `Retenue_socle_Jetson_R11.stl` | 4 | Black PLA | 07B_platine_PLA_noir | reported_printed |
-| `Plateau_Jetson_R11.stl` | 1 | Black PLA | 07C_Jetson_PLA_noir | reported_printed |
+| `Berceau_electronique_R11.stl` | 1 | Black PLA | 07A_berceau_PLA_noir | printed |
+| `Support_porte_fusible_R9.stl` | 1 | Black PLA | 07A_berceau_PLA_noir | printed |
+| `Platine_bras_R11.stl` | 1 | Black PLA | 07B_platine_PLA_noir | printed |
+| `Retenue_socle_Jetson_R11.stl` | 4 | Black PLA | 07B_platine_PLA_noir | printed |
+| `Plateau_Jetson_R11.stl` | 1 | Black PLA | 07C_Jetson_PLA_noir | printed |
- Replacement arm plate, not an additional plate stacked on top of R8/R9.
@@ -192,14 +191,14 @@ G/D and −1/+1 retain the CAD naming so parts can be matched to their source fi
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `SO101_Bras_superieur_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | reported_printed |
-| `SO101_Avant_bras_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | reported_printed |
-| `SO101_Base.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | reported_printed |
-| `SO101_Rotation_epaule.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | reported_printed |
-| `SO101_Support_epaule_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | reported_printed |
-| `SO101_Base_motor_holder.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | reported_printed |
-| `SO101_Poignet_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | reported_printed |
-| `SO101_Support_poignet.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | reported_printed |
+| `SO101_Bras_superieur_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |
+| `SO101_Avant_bras_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |
+| `SO101_Base.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |
+| `SO101_Rotation_epaule.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |
+| `SO101_Support_epaule_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |
+| `SO101_Base_motor_holder.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | printed |
+| `SO101_Poignet_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | printed |
+| `SO101_Support_poignet.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | printed |
- Four cable clips are integrated into arm parts; no additional printed clip count.
@@ -207,28 +206,28 @@ G/D and −1/+1 retain the CAD naming so parts can be matched to their source fi
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `Corps_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Machoire_gauche_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Machoire_droite_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Support_camera_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Flasque_1_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Flasque_2_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Pignon_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
-| `Guide_cable_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | reported_printed |
+| `Corps_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Machoire_gauche_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Machoire_droite_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Support_camera_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Flasque_1_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Flasque_2_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Pignon_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
+| `Guide_cable_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |
### Gripper pads
| Part / source STL | Qty | Material | Plate / job | Status |
|---|---:|---|---|---|
-| `Patin_TPU_gauche.stl` | 1 | TPU 95A | 10_patins_TPU95A | reported_printed |
-| `Patin_TPU_droit.stl` | 1 | TPU 95A | 10_patins_TPU95A | reported_printed |
+| `Patin_TPU_gauche.stl` | 1 | TPU 95A | 10_patins_TPU95A | printed |
+| `Patin_TPU_droit.stl` | 1 | TPU 95A | 10_patins_TPU95A | printed |
-## Parts to locate before calling the set complete
+### Camera brackets
-| Part | Qty | Source | Status |
-|---|---:|---|---|
-| D455 camera mounting bracket -1 | 1 | `R8_CAMERA_Equerre_D455_-1_R8.stl` | Printing not confirmed; no final plate located |
-| D455 camera mounting bracket 1 | 1 | `R8_CAMERA_Equerre_D455_1_R8.stl` | Printing not confirmed; no final plate located |
+| Part / source STL | Qty | Material | Plate / job | Status |
+|---|---:|---|---|---|
+| `R8_CAMERA_Equerre_D455_-1_R8.stl` | 1 | PETG | Standalone | printed |
+| `R8_CAMERA_Equerre_D455_1_R8.stl` | 1 | PETG | Standalone | printed |
## Superseded or excluded
@@ -243,7 +242,7 @@ G/D and −1/+1 retain the CAD naming so parts can be matched to their source fi
## Naming and release status
-The builder confirms that the **current physical prototype is V0.3**. Update the repository references that still call it V0.1 or describe V0.3 as a future release. R8, R8H, R10, R11 and V2-01 inside filenames are historical component identifiers; retain them for traceability and do not treat them as the current robot version. The next hardware revision is not assigned a new number here. A successful print and an assembled, validated part are separate milestones.
+The current physical prototype is **V0.3**. R8, R8H, R10, R11 and V2-01 inside filenames are historical component identifiers; retain them for traceability and do not treat them as the current robot version. The next hardware revision is not assigned a new number here. A successful print and an assembled, validated part are separate milestones.
## Source records
diff --git a/docs/roadmap.md b/docs/roadmap.md
index 42c409f..7d02f28 100644
--- a/docs/roadmap.md
+++ b/docs/roadmap.md
@@ -1,6 +1,6 @@
# Roadmap
-- **Now (V0.3 prototype)**: the print set is essentially complete and the power and control harness ran both motors on the bench (20 September). Integrate the harness into the chassis, set the installed motor and encoder directions, measure ticks per revolution, write the Jetson–ESP32 interface then speed control; assemble, fit and check every part on the real thing. What turns out wrong is logged in [assembly_feedback.md](assembly_feedback.md); some fixes go on the prototype, the others into the next hardware revision (not numbered yet), which also gets mounts for the ESP32-S3, the servo adapter and the real power distribution. Manufacturing files are published part by part once their validation is decided.
+- **Now (V0.3 prototype)**: the print set is complete and the power and control harness ran both motors on the bench (20 September). Integrate the harness into the chassis, set the installed motor and encoder directions, measure ticks per revolution, write the Jetson–ESP32 interface then speed control; assemble, fit and check every part on the real thing. What turns out wrong is logged in [assembly_feedback.md](assembly_feedback.md); some fixes go on the prototype, the others into the next hardware revision (not numbered yet), which also gets mounts for the ESP32-S3, the servo adapter and the real power distribution. Manufacturing files are published part by part once their validation is decided.
- **Next**: first roadside run, teleoperated with a gamepad through dimOS; first recordings.
- **Then**: mount the arm and gripper; collect pick-up demonstrations; publish the first pooled dataset.
- **Later**: first policy; first autonomous pick on video; kits so the first hundred builders do not have to source parts themselves.
diff --git a/hardware/README.md b/hardware/README.md
index 3647c2f..03a8f7f 100644
--- a/hardware/README.md
+++ b/hardware/README.md
@@ -1,6 +1,6 @@
# Hardware
-Design in Fusion 360. The current prototype is **V0.3**, being assembled from its first print set (111 pieces, see `docs/printed_parts.md`). Fit problems are logged in `docs/assembly_feedback.md`: some are fixed on the prototype, the others wait for the next hardware revision, which has no number yet.
+Design in Fusion 360. The current prototype is **V0.3**, being assembled from its first print set (113 pieces, see `docs/printed_parts.md`). Fit problems are logged in `docs/assembly_feedback.md`: some are fixed on the prototype, the others wait for the next hardware revision, which has no number yet.
Manufacturing files (STL/STEP) are published here part by part once their validation is decided, with the fastener list (type, thread, length, head, quantity, what goes into PETG with inserts) and the sources they derive from (SO-101 arm, NormaCore gripper) with exact revisions and local changes. Until then, the photos in `media/`, the inventory and the BOM are the reference.