MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.
Python
build log: first drive (22 September), track tension feedback
metrox3576351d19c2
diff --git a/README.md b/README.mdindex da6fb68..cd54d62 100644--- a/README.md+++ b/README.md@@ -14,7 +14,7 @@ MOSS is a small litter-picking rover you can print and build yourself: a tracked*We forgot to take the wide shot, so this is 41 frames of a phone pan stitched together. It wobbles a bit; the parts are real.*-All 113 printed parts are on the bench, with the shafts, bearings and screws to go with them. On 20 September the two drive motors ran for the first time, encoders counting, from the ESP32 that will drive them on the rover. By the evening the electronics were inside the chassis and the Jetson was booting from the battery. Some parts ended up elsewhere than the CAD planned; that is what a first prototype is for. It does not roll yet. Next is making it drive.+All 113 printed parts are on the bench, with the shafts, bearings and screws to go with them. On 20 September the two drive motors ran for the first time, encoders counting, from the ESP32 that will drive them on the rover. By the evening the electronics were inside the chassis and the Jetson was booting from the battery. Some parts ended up elsewhere than the CAD planned; that is what a first prototype is for. On 22 September it rolled for the first time. The tracks still have some slack, a second tensioner per track is next.diff --git a/docs/assembly_feedback.md b/docs/assembly_feedback.mdindex 712b516..6525821 100644--- a/docs/assembly_feedback.md+++ b/docs/assembly_feedback.md@@ -10,6 +10,7 @@ One line per finding: what was observed, which part and revision, what was done| Front of the cover and offset arm plate | Cover, arm plate | Keep the unfinished interface as is | Complete-cover study, parked | — || Camera brackets | Two RealSense D455 brackets | Fit at assembly | — | Not yet || Plate gasket | R8 gasket listed with the R11 plate | Check the real fit at assembly | — | Not yet |+| Track tension uneven | Single-sided tensioner per track | Live with some slack for the first drives | Second tensioner on each track | First drive, 22 September: rolls, slack visible || No mounts for the selected electronics | ESP32-S3-DevKitC-1, Bus Servo Adapter, distribution block, fuse holder (20 September architecture) | Fix in place as possible for the first tests | Design the mounts in | Harness bench-tested outside the chassis || INA219 cannot sit in the motor line | INA219 module terminal vs main cable | Voltage monitoring only; current path bypasses the shunt | Proper current sensing if wanted | I²C and voltage read confirmed; current readings invalid |diff --git a/docs/build_log.md b/docs/build_log.mdindex 6bdc634..89e1a30 100644--- a/docs/build_log.md+++ b/docs/build_log.md@@ -94,3 +94,10 @@ Mighty Camera ($92 paid) and a STEVAL-VL53L9 evaluation board ($80 paid) were orThe [new itemized budget](bom-costs.md) is $820 with Mighty or $821 with ST, compared with $1,676 for the Jetson / RealSense prototype configuration including a $250 allowance for its 2 TB SSD. These are replacement-cost planning figures, not actual expenditure. They supersede the initial $500–700 excluding Jetson target recorded on 15 September; that entry remains as history.[Comparison video, 45 seconds](../media/video/MOSS_cost_comparison_20260921.mp4).++## 2026-09-22 — first drive++MOSS rolled for the first time today: tracks on, drivetrain assembled, the rover moving on the floor under its own motors. Posted on X at 23:01 with a 10-second clip.++What the first metres taught: the single-sided track adjustment leaves the tension uneven, so there is still some slack. Next hardware step: a second tensioner on each track. This is logged in [assembly_feedback.md](assembly_feedback.md). No autonomous behaviour yet; this is a drive test.+diff --git a/docs/roadmap.md b/docs/roadmap.mdindex 5d7581f..e312c2a 100644--- a/docs/roadmap.md+++ b/docs/roadmap.md@@ -1,6 +1,6 @@# Roadmap-- **Now (V0.3 prototype)**: the print set is complete and the power and control harness ran both motors on the bench (20 September). Integrate the harness into the chassis, set the installed motor and encoder directions, measure ticks per revolution, write the Jetson–ESP32 interface then speed control; assemble, fit and check every part on the real thing. What turns out wrong is logged in [assembly_feedback.md](assembly_feedback.md); some fixes go on the prototype, the others into the next hardware revision (not numbered yet), which also gets mounts for the ESP32-S3, the servo adapter and the real power distribution. Manufacturing files are published part by part once their validation is decided.+- **Now (V0.3 prototype)**: the print set is complete and the rover rolled for the first time on 22 September. Fix the track tension (second tensioner per track), measure ticks per revolution, write the Jetson–ESP32 interface then speed control; fit the arm. What turns out wrong is logged in [assembly_feedback.md](assembly_feedback.md); some fixes go on the prototype, the others into the next hardware revision (not numbered yet), which also gets mounts for the ESP32-S3, the servo adapter and the real power distribution. Manufacturing files are published part by part once their validation is decided.- **Next**: first roadside run, teleoperated with a gamepad through dimOS; first recordings.- **Then**: mount the arm and gripper; collect pick-up demonstrations; publish the first pooled dataset.- **Later**: first policy; first autonomous pick on video; kits so the first hundred builders do not have to source parts themselves.