MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.
Python
Rewrite the repository for the reader: README as the door, BOM, 3D printing, assembly, software, story, lessons
metrox3fcd589dba5e
diff --git a/.gitignore b/.gitignoreindex c6ccc38..29d7dc7 100644--- a/.gitignore+++ b/.gitignore@@ -1,9 +1,9 @@-__pycache__/-*.pyc*.egg-info/-.venv/.env-recordings/*.f3d*.f3z+*.pyc+__pycache__/.pytest_cache/+recordings/+.venv/diff --git a/3DPrinting.md b/3DPrinting.mdnew file mode 100644index 0000000..c3d1947--- /dev/null+++ b/3DPrinting.md@@ -0,0 +1,70 @@+# 3D printing++**107 printed parts** on the assembled rover: 82 in PETG, 19 in PLA, 6 in TPU 95A. Counted on the V0.5 CAD on 1 October 2026. The STL files, one per part, land in [`hardware/`](hardware/) at the design freeze; this page is the list to plan against.++| Material | Where | Why |+|---|---|---|+| PETG | hull, hatch, drivetrain, tensioners, brackets | stiffness and heat near the motors |+| PLA (matte) | cover, bin, arm plate, SO-101 arm, NC90 gripper | big flat parts that print clean |+| TPU 95A | tracks, bin pads, gripper pads | grip |++Tracks: print with a 0.4 mm nozzle. The 0.8 mm nozzle makes them too stiff to run.++The hull is one piece, 328 mm long: it needs a large bed. A version split for 256 mm beds is not in the files yet. It is also the print that fails most often: level the bed and dry the PETG before it.++## Hull and body, PETG++| Part | Qty |+|---|---:|+| Hull, one piece | 1 |+| Motor hatch, ten fixings | 1 |+| Motor supports, left and right | 2 |+| Bearing retainers, left and right | 2 |+| Lidar mount | 1 |+| Jetson brackets | 2 |+| Inner side plates, left and right | 2 |+| Outer side plates, left and right | 2 |+| XT30 housing: base, cover, insulating separator | 3 |+| Cross-member spacers, −40 and +40, left and right | 4 |+| Motor bearing covers, left and right | 2 |++## Drivetrain, PETG++| Part | Qty |+|---|---:|+| Inner tensioner slides, left and right | 2 |+| Inner tensioner covers, left and right | 2 |+| Outer tensioner slides, left and right | 2 |+| Outer tensioner covers, left and right | 2 |+| Tensioner retainer spacers, inner and outer, left and right | 4 |+| Tensioner spacers, inner, centre, outer, left and right | 6 |+| Idler half-wheels, 22 teeth, inner and outer, left and right | 4 |+| Roller half-wheels (625 bearing), positions −70, 0, +70, inner and outer, left and right | 12 |+| Roller spacers, positions −70, 0, +70, inner, centre, outer, left and right | 18 |+| Drive half-wheels HEX12, inner and outer, left and right | 4 |+| Inner drive spacers, left and right | 2 |+| Outer drive spacers HEX12, left and right | 2 |++## Cover, bin and arm, PLA++| Part | Qty |+|---|---:|+| Top cover, with lips and magnet pockets | 1 |+| Bin, with magnet pockets | 1 |+| Arm mounting plate | 1 |+| SO-101: base motor holder, base, shoulder bracket, shoulder rotation, upper arm, forearm, wrist bracket, wrist | 8 |+| NC90 gripper: base with extended rails, two jaws with extended racks, pinion, two flanges, cable guide, camera mount with 34 mm adapter | 8 |++The SO-101 parts are the upstream files with cable clips added. The NC90 jaws and rails are lengthened for bottles and cans.++## Tracks and pads, TPU 95A++| Part | Qty |+|---|---:|+| Track, 70 teeth, pitch 10 mm, left and right | 2 |+| Bin pads, front and rear | 2 |+| Gripper pads, left and right | 2 |++## Filament++Sliced so far, supports included: 1.15 kg of PETG and 1.1 kg of PLA for the hull, cover (465 g), bin (549 g), arm plate and brackets. The drivetrain, arm and tracks add to it. Plan on 2 kg of PETG, 2 kg of PLA and a roll of TPU.diff --git a/Assembly.md b/Assembly.mdnew file mode 100644index 0000000..131845a--- /dev/null+++ b/Assembly.md@@ -0,0 +1,55 @@+# Assembly++**Photos from the first prototype, V0.3, September 2026.** The step-by-step with the V0.6 parts is shot during the rebuild and replaces this page when the files come out. Read [docs/lessons.md](docs/lessons.md) before you start: it is short, and it is everything that bit us.++## 1. Lay out the print set++++Check every part against the [list](3DPrinting.md). Push the bearings into the half-wheels and rollers now, while they are easy to reach.++## 2. Drivetrain plates++++++Rollers on their Ø5 shafts, idler wheels on Ø8, drive wheels on the HEX12 hubs. Collars on both sides of every shaft. Both tensioners on each side, slides and covers.++## 3. Motors, encoders and the control board on the bench++++Flash the [firmware](firmware/), wire one motor at a time, run `test left 10` and `test right 10` and watch the encoder counts climb in the telemetry. Do this before anything goes into the hull.++## 4. Electronics into the hull++++++Motor driver, controller, servo adapter, power distribution and fuse into their mounts. Battery under the arm plate. Screw terminals, not jumper wires.++## 5. Tracks on++++Fit the tracks, tension both sides until there is no sag under the hull, then put the rover on blocks and run `drive 10 10`. First drive on the floor only after that.++## 6. Bin and cover++++Magnets in the cover and in the bin, pads under the bin.++## 7. Arm and gripper++++++Build the SO-101 arm with the upstream guide, then the NC90 gripper. Bolt the arm plate to the hull, route the servo bus and the camera cable through the clips.++## 8. Computer and sensors++Jetson or Pi on its plate, depth camera at the nose with the right-angle USB cable, lidar on its mount. Then [Software](Software.md).diff --git a/BOM.md b/BOM.mdnew file mode 100644index 0000000..3bb44e8--- /dev/null+++ b/BOM.md@@ -0,0 +1,110 @@+# Bill of materials++**Estimates, retail, one rover.** Checked against the V0.5 CAD on 1 October 2026. Prices in USD; a line marked *paid* is what we actually paid, the others are listings or allowances. A kit will cost less: filament by the gram instead of the spool, servos and bearings in volume.++## Totals++| | Kit base | Jetson + RealSense | Pi + Hailo + Gemini |+|---|---:|---:|---:|+| Kit base (everything below) | 482 | 482 | 482 |+| Computer | | 730 | 218 |+| AI accelerator | | on board | 232 |+| Depth camera | | 466 | 234 |+| 2D lidar | | 72 | 72 |+| **Total** | **about $480** | **about $1,750** | **about $1,240** |++The Jetson configuration is the prototype. The Pi configuration is drawn, not yet run.++## Computer and perception++| Item | Qty | USD | Note |+|---|---:|---:|---|+| NVIDIA Jetson Orin Nano Super 8 GB | 1 | 480 | plus a 2 TB NVMe SSD, allowance 250 |+| Intel RealSense D455 | 1 | 466 | *paid*. Depth from 0.12 m with the current close-range software |+| USB 3.1 C to A cable, 90° plug with locking screws, 0.3 m | 1 | 7 | *paid*. The straight plug does not fit in the hull |+| Raspberry Pi 5 8 GB | 1 | 175 | with active cooler 8, 5 V supply 20, microSD 15 |+| Raspberry Pi AI HAT+ 2 (Hailo-10H, 40 TOPS) | 1 | 232 | *paid*; list price about 200 |+| Orbbec Gemini 2 | 1 | 234 | listing. Depth from 0.15 m, 91° × 66° |+| SLAMTEC RPLIDAR C1 | 1 | 72 | listing (RobotShop, DFRobot). Mount printed; position on the cover still being settled |++## Kit base, about $482++| Block | USD |+|---|---:|+| Control electronics | 49 |+| Drive | 30 |+| Arm and gripper | 160 |+| Power and wiring | 90 |+| Mechanical hardware | 61 |+| Filament | 87 |+| Fans and magnets | 5 |++### Control electronics++| Item | Qty | Unit | Line | Note |+|---|---:|---:|---:|---|+| Adafruit QT Py ESP32-S3, 8 MB flash, no PSRAM (5426) | 1 | 12.50 | 12.50 | *paid* |+| Adafruit Terminal Block BFF (6495) | 1 | 10.95 | 10.95 | *paid*. Screw terminals instead of jumper wires |+| Adafruit INA219 STEMMA QT (904) | 1 | 9.95 | 9.95 | *paid*. Battery voltage only |+| STEMMA QT cable, 300 mm (5384) | 1 | 1.25 | 1.25 | *paid* |+| Cytron MDD3A dual motor driver, 4–16 V, 3 A per channel | 1 | 9.53 | 9.53 | listing |+| Waveshare Bus Servo Adapter (A) | 1 | 5 | 5 | estimate |++### Drive++| Item | Qty | Unit | Line | Note |+|---|---:|---:|---:|---|+| 12 V geared DC motor with quadrature encoder | 2 | 15 | 30 | estimate; exact reference to pin with the files |++### Arm and gripper++| Item | Qty | Unit | Line | Note |+|---|---:|---:|---:|---|+| ST3215 12 V bus servo | 5 | 22 | 110 | arm joints |+| CF35-12 constant-force servo | 1 | 50 | 50 | gripper |++The small camera in the hand (Waveshare 38 mm USB camera in the CAD) is not priced yet.++### Power and wiring++| Item | Qty | Unit | Line | Note |+|---|---:|---:|---:|---|+| 3S lithium pack with BMS | 1 | 35 | 35 | allowance; pack not specified yet |+| 12.6 V CC/CV charger | 1 | 12 | 12 | estimate |+| Emergency stop (16 mm, LA16-11ZS/A), fuse holder, fuses, distribution | lot | 18 | 18 | e-stop *paid* 2.23 |+| Wiring, ferrules, heat-shrink, 2 × DC 5.5 × 2.1 mm panel sockets | lot | 15 | 15 | sockets *paid* 1.51 each |+| XT30 pairs: one input, four outputs (arm, computer, driver, fans) | 5 | | | not priced yet; printed housing |+| USB cables for the controller and the servo adapter | lot | 10 | 10 | estimate |++### Mechanical hardware++| Item | Qty | Note |+|---|---:|---|+| Bearings 625 | 12 | two per roller |+| Bearings 608 | 4 | two per idler wheel |+| Bearings 626 | 4 | motor side and outer |+| Shaft collars Ø5, Ø6, Ø8 bore | 12, 2, 4 | Ø8 *paid* 2.14 each |+| Shafts: Ø5 × 80 (6), Ø6 × 90 (2), Ø8 × 100 (2) mm | 10 | cut from Ø5 × 500, Ø6 × 250, Ø8 × 250 mm bars |+| Rigid motor-to-shaft couplings, Ø6 bores | 2 | |+| HEX12 metal wheel hubs, Ø6 bore, 18 mm | 2 | drop if supplied with the motors |++Bearings about 12, collars 18, bars 8, couplings 5, hubs 3, screws 15: about $61.++Screws in the drivetrain: M3 × 16 (22), M3 × 20 (6), M3 × 25 (6), M3 × 35 (18), M4 × 16 (6), M4 × 40 (4), M4 × 60 (4), M2.5 × 10 (4); 52 M3 nuts, 18 M4 nuts (4 lock nuts), 8 M4 washers. The hull hatch and the arm add M3 positions whose lengths are fixed with the files.++### Filament++| Filament | Qty | Unit | Line | Note |+|---|---:|---:|---:|---|+| PETG, black | 2 kg | 10.39 | 20.79 | *paid* |+| PLA, matte | 2 kg | 20.64 | 41.27 | *paid* |+| TPU 95A | 1 kg | 25 | 25 | tracks and pads |++The sliced hull, cover, bin and brackets alone use 1.15 kg of PETG and 1.1 kg of PLA. See [3D printing](3DPrinting.md).++### Fans and magnets++| Item | Qty | Unit | Line | Note |+|---|---:|---:|---:|---|+| 3010 fan, 12 V | 2 | 1.68 | 3.35 | *paid*. Rear extraction |+| Magnet 20 × 10 × 2 mm | 4 | 0.43 | 1.73 | *paid*. Two in the cover, two in the bin |diff --git a/CHANGELOG.md b/CHANGELOG.mdnew file mode 100644index 0000000..304ad18--- /dev/null+++ b/CHANGELOG.md@@ -0,0 +1,8 @@+# Changelog++Hardware revisions. Dates are when it was real, not when it was planned.++- **V0.6** (October 2026, prototype being assembled): modular compute and perception plates (Jetson or Raspberry Pi; RealSense or Orbbec Gemini), XT30 power block, 12 V to 5 V converter for the Pi, hull R7, tracks 70 teeth at 10 mm pitch.+- **V0.5** (1 October 2026): redrawn on the real V0.3 robot; one-piece hull, two tensioners per track, mounts for every board, magnets for the bin. Release candidate for the open source CAD. 107 printed parts.+- **V0.4** (24 September 2026, drawn, parts printed): revised hull, screw-terminal controller, one dual motor driver.+- **V0.3** (22 September 2026): first prototype. First drive on 22 September, arm and gripper on 26 September.diff --git a/CITATION.cff b/CITATION.cffnew file mode 100644index 0000000..63fb8fd--- /dev/null+++ b/CITATION.cff@@ -0,0 +1,8 @@+cff-version: 1.2.0+message: "If you use MOSS, please cite it."+title: "MOSS: an open hardware litter-picking rover"+authors:+ - family-names: "metrox"+type: software+repository-code: "https://github.com/metrox-eth/moss"+license: Apache-2.0diff --git a/CLAUDE.md b/CLAUDE.mddeleted file mode 100644index 6e07e31..0000000--- a/CLAUDE.md+++ /dev/null@@ -1,10 +0,0 @@-# MOSS — working notes for coding agents--MOSS is a small open-source litter-picking rover. This repository is public. Keep it readable for a builder who has never seen it.--- **Software first, cold tests always.** Anything in `moss_dimos/` or a new `moss_pi/` package must run and be tested without the robot: fake serial, recorded telemetry, pure functions. A test passes only when a known input gives a known output in physical units.-- **The firmware contract is the source of truth.** Serial, 115200 baud, line-based commands (`status`, `stop`, `zero`, `arm`, `drive LEFT RIGHT` with -25..+25, `test left|right PERCENT`), JSON telemetry about every 200 ms. See `firmware/README.md`. Do not invent commands; propose firmware changes as a separate PR.-- **Motors never move by accident.** Every drive path needs an explicit arm step and a deadman; a lost link means stop.-- **Docs are for the reader, not a diary.** The README is the door: what it is, where it stands, how to enter. Details go to `docs/`. No order or delivery status anywhere; a state is what exists and what is validated.-- **Nothing private.** No names of third parties, no addresses, no keys, no internal context. Replacement-cost estimates, not receipts.-- **One PR per scoped change**, with what was tested and what remains a hypothesis stated in the description.diff --git a/README.md b/README.mdindex fd74050..e317543 100644--- a/README.md+++ b/README.md@@ -2,65 +2,62 @@Cleaner streets, one maker at a time.-MOSS is a small litter-picking rover you can print and build yourself: a tracked base, a bin, and an arm derived from the SO-101 with a parallel gripper. About $1,700 in parts as built, with a Jetson and a RealSense; a Raspberry Pi version around $820 is the next experiment. It is being built in public.+MOSS is a small litter-picking rover you print and build yourself: a tracked base, a bin on top, an arm derived from the SO-101 with a parallel gripper. It is open hardware, built in public, and meant to be built by many hands.-**New here?** The day-by-day story is in the [build log](docs/build_log.md); what did not fit is in the [assembly feedback](docs/assembly_feedback.md); what it costs is in the [itemized budget](docs/bom-costs.md).+-**Want one?** [Join the community waitlist](https://ak4khuvxkya.typeform.com/to/qaKmXNME) with [Tnkr](https://x.com/tnkrdotai) and we'll let you know when the open source CAD files and MOSS kits are ready.+**Where it stands.** The first prototype rolls and carries its arm. Nothing has picked up litter on its own yet. The CAD is being finished on the real robot, and the files come out after one test: a full battery emptied over 3 km on the beach, tracks still on, no bolt lost. No date; it is posted when it is real.-+## Two ways to get one-*40-second CAD animation of the V0.4 design: inside the hull, reassembly, and a scripted pickup. The physical prototype drives; autonomous pickup is still ahead. [Video version](media/video/MOSS_V04_Inside_and_Action_20260924.mp4).*+- **Build it yourself.** [Bill of materials](BOM.md) → [3D printing](3DPrinting.md) → [Assembly](Assembly.md) → [Software](Software.md). The STL and STEP files land in [`hardware/`](hardware/) when the design is frozen.+- **Get the kit.** Kits and an interactive build guide are coming with [Tnkr](https://x.com/tnkrdotai). [Join the waitlist](https://ak4khuvxkya.typeform.com/to/qaKmXNME) to hear when the files and the kits are ready.-## Where it stands+## What it costs-+Retail estimates for one rover, parts only. A kit will be cheaper.-*We forgot to take the wide shot, so this is 41 frames of a phone pan stitched together. It wobbles a bit; the parts are real.*--All 113 printed parts are on the bench, with the shafts, bearings and screws to go with them. On 20 September the two drive motors ran for the first time, encoders counting, from the ESP32 that will drive them on the rover. By the evening the electronics were inside the chassis and the Jetson was booting from the battery. Some parts ended up elsewhere than the CAD planned; that is what a first prototype is for. On 22 September it rolled for the first time. The tracks still have some slack, a second tensioner per track is next.----In parallel, **V0.4** is being drawn from the assembly feedback: a revised hull, screw-terminal control electronics, one dual motor driver instead of two. Not built yet. See the [V0.4 hardware update](docs/hardware_v04.md).+| Configuration | Parts |+|---|---:|+| Kit base: chassis, tracks, arm, gripper, power, filament | about $480 |+| + Jetson Orin Nano Super, RealSense D455, 2D lidar | about $1,750 |+| + Raspberry Pi 5, Hailo AI HAT, Orbbec Gemini 2, 2D lidar | about $1,240 |-Every step is written down when it is real, good or bad. The [build log](docs/build_log.md) has the dates and the numbers, the [assembly feedback](docs/assembly_feedback.md) has what did not fit, the [roadmap](docs/roadmap.md) has what comes next, without dates.+The Jetson configuration is the one on the bench. The Pi configuration is drawn, not yet run. Every line is in the [BOM](BOM.md).-## What does it cost?+-| Build | Parts estimate |-|---|---:|-| As built: Jetson Orin Nano Super, RealSense D455, 2 TB SSD | about $1,680 |-| Next experiment: Raspberry Pi 5, Mighty Camera | $820 |-| Next experiment: Raspberry Pi 5, ST 3D time-of-flight | $821 |+## What it is made of-Replacement-cost estimates for every part, not receipts. The Pi builds keep the same chassis, arm and drivetrain, and have not been tested yet. Every line, assumption and source is in the [itemized budget](docs/bom-costs.md); the [45-second comparison](media/video/MOSS_cost_comparison_20260921.mp4) tells it in pictures.+- Tracked base, two geared DC motors with encoders, printed TPU tracks, an ESP32-S3 driving the motors.+- A bin you empty by hand at the end of a run.+- An SO-101 arm (open source) with a NormaCore NC90 gripper and a small camera in the hand.+- A depth camera at the nose, a 2D lidar for navigation.+- Software: dimOS for teleop and navigation, LeRobot for data and policies. A Raspberry Pi path without dimOS for the first drives.-## Try the demo+The rule we build by: pick up more litter with less technology. Every part has to earn its place against a person with a bag.-Jev, TypeSafe AI's decision model, choosing every step of a pickup (approach, align, grasp, lift, carry, release) on physics recorded once in MuJoCo, replayed in 3D in your browser. Three missions with real Jev decisions, plus the earlier target-choice scenarios: https://www.showrobotics.ai/moss-jev/+## News-[](https://www.showrobotics.ai/moss-jev/)+- 3 October 2026: V0.6 makes the hardware modular, Pi or Jetson, RealSense or Gemini. Waitlist open with Tnkr.+- 1 October 2026: V0.5, the release candidate for the open source CAD.+- 26 September 2026: arm and gripper mounted on the prototype.+- 22 September 2026: first drive.-The simulator behind it is open too: the MOSS body as a MuJoCo model with its meshes, the three recorded missions, and a CPU replay that needs no API key, in the demo repository's [`live/` folder](https://github.com/metrox-eth/moss-jev/tree/main/live). Import the body into your own lab, or replay the missions on your laptop.+## Friends-## What is in here+[Dimensional](https://x.com/dimensionalos) (dimOS), [NormaCore](https://x.com/norma_core_dev) (gripper), [Tnkr](https://x.com/tnkrdotai) (kits and guide), [Dirac Robotics](https://x.com/diracrobotics) (calibrated simulation), [microduck-lab](https://github.com/jonathanhawkins/microduck-lab) (reinforcement learning). We help each other.-- `docs/` what MOSS is for, the build log, the bill of materials, the printed-parts list, the data rules, the roadmap.-- `firmware/` the ESP32-S3 code that drives the motors, with its test.-- `moss_dimos/` the Jetson side, on dimOS. Cold-tested only, for now.-- `moss_pi/` the Raspberry Pi side: drives the same motor firmware over serial, keyboard or gamepad teleop, telemetry log. Cold-tested only, for now.-- `hardware/` the design files, published part by part as they prove themselves on the real robot, and the raw bench traces.-- `media/` the videos and photos.+## Come and build-## Build one, or come and watch+Ask anything, tell us what we are doing wrong, it helps the next builder: [Discord](https://discord.com/invite/x2MeNmgveT). The build, as it happens: [@metrox_eth](https://x.com/metrox_eth). The story so far, in a few moments: [STORY.md](STORY.md). What we learned the hard way: [docs/lessons.md](docs/lessons.md). How data from many rovers gets pooled: [docs/data.md](docs/data.md).-The design files are not out yet. The first MOSS now rolls; we are incorporating its assembly feedback into V0.4 before releasing the parts and their matching BOM. Until then, the door is the Discord: ask anything, tell us what we are doing wrong, it helps the next builder too. https://discord.com/invite/x2MeNmgveT+Try the simulator: the MOSS body in MuJoCo, with three recorded pickup missions, in the [moss-jev](https://github.com/metrox-eth/moss-jev) repository.-The build, day by day, is on X: [@metrox_eth](https://x.com/metrox_eth).+## Safety-Data recorded by MOSS builders is meant to be pooled and open, so the shared model gets better with every robot. The rules we propose are in [docs/data.md](docs/data.md).+This is a prototype with a lithium battery, motors strong enough to pinch, and no certified protection. Put it on blocks for the first run. Build at your own risk.## License-Code under Apache-2.0. Hardware files and documentation under CC BY 4.0. See `NOTICE`.+Code under Apache-2.0. Hardware files and documentation under CC BY 4.0 until the first file release, which will carry the hardware license named in `NOTICE`.diff --git a/STORY.md b/STORY.mdnew file mode 100644index 0000000..38a9256--- /dev/null+++ b/STORY.md@@ -0,0 +1,39 @@+# The story so far++*Six moments. This page is written by Laurent, in his words; the dates and facts below are the frame, the lines in italics are placeholders for him.*++## 15 September 2026, a video before a robot++A 40-second concept video: a tracked rover with a bin and an arm, picking a can off the ground. Target cost said out loud: five to seven hundred dollars plus a computer. Nothing printed yet.++*What it felt like to post it, and why this robot and not another.*++## 16–19 September, the print set++Two printers for three days. The bin and a track the first evening, the hull in black PETG on the 18th. By the 19th, 113 parts on the bench, shafts and bearings in bags next to them. We forgot to take the wide shot and stitched a phone pan instead.++*The first part in hand, the first one that did not fit.*++## 20 September, the motors turn++Both motors on the bench, encoders counting, driven by the ESP32 that would drive them on the rover. Same evening, the electronics went into the hull and the Jetson booted from the battery.++*The moment the counts climbed.*++## 22 September, first drive++Tracks on, the rover moving and turning on the floor under its own motors, still tethered. The tracks had slack: one tensioner per side is not enough. That went into the next revision the same day.++*What you did right after.*++## 26 September, the arm++A standard SO-101 bolted on, gripper included, with a camera in the hand. Folded over the bin, it looks like the video. A reader looked at the photo and said the shoulder looked weak. He was right, and it became an issue.++*What a stranger seeing it taught you.*++## 1–3 October, the files are close++V0.5, redrawn on the real robot, is the release candidate for the CAD. V0.6 makes the hardware modular: Pi or Jetson, RealSense or Gemini, same chassis. Kits and a build guide are coming with Tnkr; the waitlist opened. The files come out after one test: a full battery emptied over 3 km on the beach, tracks still on, no bolt lost.++*What the beach test means to you.*diff --git a/Software.md b/Software.mdnew file mode 100644index 0000000..d147ac4--- /dev/null+++ b/Software.md@@ -0,0 +1,55 @@+# Software++Three layers. The microcontroller drives the motors. The computer on top sends it speeds and reads its telemetry. The policies come later, from pooled data.++**State: the motor firmware ran on the bench and on the first drives. Everything on the computer side is tested against a fake serial port only; nothing has driven the rover from a Jetson or a Pi yet.**++## Motor firmware, ESP32-S3++[`firmware/`](firmware/). Newline-terminated commands over USB serial at 115200 baud:++| Command | What it does |+|---|---|+| `status` | one telemetry line |+| `arm` | ready to drive, for 10 s if no drive comes |+| `drive L R` | track speeds, −25 to +25 percent; must be repeated, 300 ms without one stops and disarms |+| `test left 10` | one motor for one second, bench only |+| `stop` | stops and disarms |+| `zero` | resets the encoder counts (disarmed only) |++Telemetry every 200 ms as JSON: mode, raw encoder ticks, battery voltage. Disarmed at boot, nothing moves by itself. The 25 % limit is the commissioning limit; it stays until speed control exists. No speed loop, no odometry in metres yet.++The board reads battery voltage through an INA219. It does not measure motor current: the shunt is not in the motor line.++## Driving from a Raspberry Pi, `moss_pi/`++Keyboard or gamepad teleop, no dimOS, Python standard library plus pyserial (and pygame for a pad).++```+python3 -m venv .venv && . .venv/bin/activate+pip install -e '.[pi,test]'+python -m pytest tests # no robot needed+sudo usermod -aG dialout "$USER" # once, then log in again+ls /dev/serial/by-id/ # find the USB-UART adapter+python -m moss_pi.teleop --port /dev/ttyUSB0 --keyboard # r arm, hold w/s/a/d, space stop, q quit+python -m moss_pi.teleop --port /dev/ttyUSB0 --gamepad # A arm, hold L1 to drive, R1 boost+python -m moss_pi.telemetry_log --port /dev/ttyUSB0 --out telemetry.jsonl+```++Nothing moves until you arm with the deadman released. Hold the deadman to drive; release and it brakes, then disarms. The stick is open loop: full stick is 25 % duty. Put the rover on blocks for the first run.++## Driving from a Jetson, `moss_dimos/`++The dimOS side: a gamepad module publishing a Twist behind a deadman, differential-drive kinematics, the same pure teleop logic as the Pi path. The driver that speaks to the firmware from dimOS, speed control and odometry are not written yet. Navigation and the pick come from dimOS once the base is reliable.++## Data and policies++Demonstrations are recorded in the LeRobot format with the same camera names on every rover, so datasets pool without rework. The rules are in [docs/data.md](docs/data.md). The simulator (MuJoCo body, three recorded pickup missions) is in [moss-jev](https://github.com/metrox-eth/moss-jev).++## Tests++```+python -m pytest tests+```++Cold tests only: a fake serial port replaying a real bench session, and a Linux pseudo-terminal. The firmware's host logic test is `firmware/tests/control_test.cpp`, any C++17 compiler.diff --git a/docs/assembly_feedback.md b/docs/assembly_feedback.mddeleted file mode 100644index 18ba014..0000000--- a/docs/assembly_feedback.md+++ /dev/null@@ -1,35 +0,0 @@-# Assembly feedback — V0.3 prototype--One line per finding: what was observed, which part and revision, what was done on the prototype, what is planned for the next revision, and what validation actually happened. The first physical drive happened on 22 September; each row below distinguishes that observation from unvalidated V0.4 changes.--| Finding | Part / revision | On the prototype | Next revision | Validation done |-|---|---|---|---|---|-| TPU track too stiff | Track printed with a 0.8 mm nozzle | Not used; the 0.4 mm profile (nozzle, extrusion width, walls, layer height, infill, material) is the reference | Record the full print profile with the part | 0.4 mm track: manual floor test, good flexibility and grip |-| Motor mounts | Corrected brackets Ø31 / M3 (files marked V2-01) | Check screw depth at assembly | — | Not yet |-| Motor mount to hull joint | Interior access is difficult | Head recesses / through access drilled on the prototype | Exterior-access recessed M4 heads and captive nuts in the motor support; standard M4 × 20 in the CAD study | Local CAD checks; complete printed joint and tool access still to validate |-| Front of the cover and offset arm plate | Cover, arm plate | Keep the unfinished interface as is | Complete-cover study, parked | — |-| Camera brackets | Two RealSense D455 brackets | Fit at assembly | — | Not yet |-| Plate gasket | R8 gasket listed with the R11 plate | Check the real fit at assembly | — | Not yet |-| Track tension uneven | Single-sided tensioner per track | Live with some slack for the first drives | Second tensioner on each track | First drive, 22 September: rolls, slack visible |-| No mounts for the selected electronics | ESP32-S3-DevKitC-1, Bus Servo Adapter, distribution block, fuse holder (20 September architecture) | Fix in place as possible for the first tests | Design the mounts in | Harness bench-tested outside the chassis |-| INA219 cannot sit in the motor line | INA219 module terminal vs main cable | Voltage monitoring only; current path bypasses the shunt | Proper current sensing if wanted | I²C and voltage read confirmed; current readings invalid |--Available M4 heat-set inserts are an option for the next revision, not a validated feature of this prototype.--## V0.4 follow-up — 24 September--| Finding / request | V0.4 response | Status |-|---|---|---|-| Jetson caddy and cables do not fit | Integrated seat for the original plastic base, retainers and USB-side cable route | Current hull CAD; printed fit pending |-| Individual Dupont connections are inconvenient | QT Py ESP32-S3 with screw-terminal BFF and STEMMA QT INA connection | Two sets ordered; wiring and firmware migration pending |-| Two MD10Cs take more space than needed | One Cytron MDD3A dual driver | Ordered earlier, selected for CAD; rover validation pending |-| RealSense straight USB plug lacks clearance | Ordered right-angle USB3 cable; housing reserve | Cable dimensions and USB3 stability untested |-| INA connector access | Existing module model and fixings rotated 90 degrees | Approximate existing-board CAD; new Adafruit footprint not yet reconciled |-| Battery installation under arm | Current pack 67 × 74 × 27 mm; larger 75 × 82 × 32 mm candidate envelope | Envelope only; detachable lower platform deferred |-| Bin retention | Four 40 × 10 × 5 mm magnets | Ordered; mounting design pending |-| Wheel / roller screws protrude | Recess the screw heads | Requested; not claimed implemented |-| Hard-to-source screw lengths | Standard readily available lengths, without custom cutting | Design rule; full fastener audit pending |-| Tracks may be too long | Test maximum adjustment and candidate one-tooth shortening | Hypothesis; no validated new belt length |-| Separate fuse mount takes space | Inline fuse holder on a cable | Selected arrangement; final full-robot rating not established |--Keep the corrected flank geometry. Do not move the fourth fixing solely because of the initial wrong-rail tensioner placement. See [the complete V0.4 status](hardware_v04.md).diff --git a/docs/bom-costs.md b/docs/bom-costs.mddeleted file mode 100644index ae4b830..0000000--- a/docs/bom-costs.md+++ /dev/null@@ -1,120 +0,0 @@-# MOSS parts budget — prototype and Raspberry Pi experiments--**21 September 2026 · USD · hardware prototype V0.3**--This comparison replaces the initial $500–700 target excluding the Jetson. It values reused hardware at replacement cost so that a new builder can see the scope. It is not the prototype's actual cash expenditure, a supplier quote, or a validated kit BOM. The [current hardware inventory](bom.md) and [113-piece print inventory](printed_parts.md) remain separate references.--## Three configurations--| Budget category | Prototype: Jetson + D455 | Pi 5 + Mighty | Pi 5 + ST ToF |-|---|---:|---:|---:|-| Shared mechanics, arm/gripper, drive, control and power | $480 | $480 | $480 |-| Computer, cooling and computer-specific power | $480 | $203 | $203 |-| Storage | $250: 2 TB SSD allowance | $15: 128 GB microSD | $15: 128 GB microSD |-| Sensors and dedicated connections | $466 | $122 | $123 |-| **Estimated total** | **$1,676** | **$820** | **$821** |-| Optional Hailo AI HAT+ | — | +$70 | +$70 |--The video rounds the prototype to **about $1,680**. The two Pi columns are alternatives, not a combined sensor stack. Neither contains a Jetson, RealSense or 2D lidar. Both retain a colour camera for litter detection. The prototype retains its 2 TB SSD; the Pi budgets use microSD only.--**The $250 SSD amount is an unverified allowance**, not a confirmed model or paid price. Change it dollar-for-dollar when the actual value is available. Of the $856 difference between prototype and Pi/Mighty, $235 comes from changing storage. With a $15 storage allowance on both sides, the difference would be $621. No equivalent navigation or inference performance has been demonstrated.--## Shared parts — $480--All amounts below are estimates or rounded budget allowances. Quantities are planning quantities; confirm them against the final assembly before purchasing. The CF35-12 allowance rounds a $49.99 supplier listing. Servo gearing and motor specifications still need exact purchasable references.--| Item | Quantity | Unit / lot USD | Line USD |-|---|---:|---:|---:|-| Espressif ESP32-S3-DevKitC-1 | 1 | 13 | 13 |-| Waveshare Bus Servo Adapter (A) V1.1 | 1 | 5 | 5 |-| Cytron MD10C R3 motor driver | 2 | 18 | 36 |-| 12 V geared DC motor with quadrature encoder | 2 | 15 | 30 |-| ST3215 12 V arm joint servo | 5 | 22 | 110 |-| CF35-12 constant-force gripper servo | 1 | 50 | 50 |-| Assembled 3S battery with BMS, replacement allowance | 1 | 35 | 35 |-| Compatible 12.6 V CC/CV charger | 1 | 12 | 12 |-| Accessible motor/servo power cut, fuse holders, fuses and distribution | 1 lot | 18 | 18 |-| Power/signal wiring, XT60, ferrules, terminals and heat-shrink | 1 lot | 15 | 15 |-| USB control cables for ESP32 and servo adapter | 1 lot | 10 | 10 |-| INA219 battery-voltage monitor | 1 | 5 | 5 |-| Bearings: 12 × 625, 4 × 608, 4 × 626 | 20; lot budget | 12 | 12 |-| Shaft collars: 12 × Ø5, 4 × Ø8, 2 × Ø6 mm | 18; lot budget | 18 | 18 |-| Shaft stock: Ø5 × 500, Ø6 × 250, Ø8 × 250 mm | 1 of each; lot | 8 | 8 |-| Rigid Ø6–Ø6 mm couplings, Ø14 × 22 mm envelope | 2 | 2.5 | 5 |-| Compatible metal hex wheel hubs | 2 | 1.5 | 3 |-| Screws, nuts, washers, inserts and small spacers | 1 lot | 15 | 15 |-| Black PETG filament | 2 kg | 18 | 36 |-| PLA filament | 1 kg | 14 | 14 |-| TPU 95A filament | 1 kg | 25 | 25 |-| Enclosure ventilation, fan/filter/grille | 1 lot | 5 | 5 |-| **Shared total** | | | **480** |--- The arm budget is **five ST3215 joint servos plus one CF35-12 for the MOSS gripper**. It is not the standard SO-101 servo set.-- Battery and charger are replacement allowances. The prototype uses a reused pack; this table does not establish its capacity, BMS thresholds or runtime. A future pack design needs its own qualification.-- The INA219 line budgets voltage monitoring. The prototype's R100 shunt is bypassed by motor current; this is not a main-rail current measurement design.-- The power/distribution allowance does not specify a final whole-robot fuse rating. The existing 5 A bench-test rating is not a completed rover rating.-- Filament amounts budget whole spools, not measured part masses. Use the print inventory for each part's material; buying lots of fasteners or bearings may cost more than the consumed quantities shown here.-- Shaft stock, hub fits and fasteners must be checked against the assembled revision. These budget lines do not replace cutting drawings. Remove the hub allowance if hubs are included with the motors. The prototype's earlier hardware order is already represented by these lines; do not add its entire order total again.--Shared category subtotals used in the video: arm/gripper $160; motors/drivers $66; mechanics/filament $136; control/power/wiring/ventilation $118.--## Compute and storage--| Item | Prototype | Each Pi option | Price basis |-|---|---:|---:|---|-| Jetson Orin Nano Super 8 GB kit, cooling included | $480 | — | Current sourcing reference reported by the builder |-| Raspberry Pi 5 8 GB | — | $175 | Selected budget reference; PiShop listing |-| Active Pi cooler | — | $8 | Estimate |-| Battery-to-Pi regulated supply, target 5.1 V / 5 A continuous | — | $20 | Estimate; module and interface not qualified |-| 2 TB SSD | $250 | — | Allowance; model and paid price unconfirmed |-| 128 GB A2 microSD | — | $15 | Estimate |-| **Compute, cooling, specific power and storage** | **$730** | **$218** | |--The Jetson boots from the prototype battery in the reported assembly. No extra Pi-specific converter is charged to that column. The Pi needs a suitable power path for both board and peripherals; verify voltage, current capability and USB-C current recognition where applicable. The $20 allowance is not approval of an arbitrary buck converter.--## Sensor options--| Item | Prototype | Pi + Mighty | Pi + ST | Price basis |-|---|---:|---:|---:|---|-| RealSense D455, RGB and IMU included | $466 | — | — | Builder's paid price |-| Mighty Camera, onboard IMU | — | $92 | — | Paid price; ordered 21 September |-| STEVAL-VL53L9 evaluation board | — | — | $80 | Paid price; ordered 21 September |-| Fixed colour USB UVC camera | — | $25 | $25 | Estimate |-| Separate compatible IMU | — | — | $8 | Estimate |-| Dedicated sensor connection / adaptation | — | $5 | $10 | Estimate; ST adapter not yet identified |-| **Sensor subtotal** | **$466** | **$122** | **$123** | |--**Mighty:** onboard visual-inertial pose estimation, with a monochrome tracking camera and IMU. Its loop-closure feature is documented as beta and disabled by default; it should not be treated as a proven persistent map. Obstacle mapping and integration with dimOS on the Pi remain to be tested. The separate RGB camera is for colour litter detection.--**ST:** the VL53L9CX evaluation board provides 3D ToF depth, with 2.3K zones and a manufacturer-stated range up to 9 m under suitable conditions. It is a forward depth sensor, not a 360° 2D scanner or a complete SLAM system. Localisation would combine encoders, an IMU and geometric/visual correction. Pi driver, MIPI/I3C connection, acquisition, power and RGB/depth calibration remain to be qualified. The supplier estimates one unit in stock on **28 October 2026**; that is not a guaranteed delivery date.--Both sensors were ordered; neither alternative navigation configuration has been validated on MOSS. dimOS is the intended software stack for the experiments. Test detection rate, tracking drift, low obstacles, outdoor behaviour, RAM use and thermal limits before describing either as a reproducible navigation build.--## Optional accelerator and exclusions--A **Raspberry Pi AI HAT+ 13 TOPS (Hailo-8L)** adds a $70 budget reference: **$890 / $891** with Mighty / ST. It is optional. It needs a compatible detector and software stack; it does not automatically accelerate mapping or replace CUDA across the application.--A wrist camera, gamepad, tools, printer, labour, development computer, electricity and API/service usage are not included in any column. Additional shipping, import costs and taxes are not added; reported paid prices may already contain some charges that are not itemised. Most lines are estimates, so allow a separate contingency before buying. This is a component budget, not a selling price.--## Sources and price provenance--Accessed for the 21 September comparison; prices and availability vary by location.--- [Raspberry Pi 5 8 GB — PiShop](https://www.pishop.us/product/raspberry-pi-5-8gb/): $175 budget reference retained for both Pi builds.-- [Raspberry Pi AI HAT+](https://www.raspberrypi.com/products/ai-hat/): optional 13 TOPS board.-- [Mighty documentation](https://mightycamera.com/docs), [SDK](https://mightycamera.com/docs/sdk) and [development history](https://mightycamera.com/story).-- [STEVAL-VL53L9 — STMicroelectronics](https://www.st.com/en/evaluation-tools/steval-vl53l9.html): evaluation board specifications and interfaces.-- [CF35-12 — Waveshare](https://www.waveshare.com/product/robotics/motors-servos/servos/cf35-12.htm): rounded $50 allowance.-- [Waveshare Bus Servo Adapter (A)](https://docs.waveshare.com/Bus_Servo_Adapter_A): interface reference.-- Jetson $480: builder-reported current price. RealSense $466, Mighty $92 and ST $80: builder-reported paid prices, not guaranteed retail offers. A separately reported Thai Jetson quote of 19,600 THB is not treated as equivalent to $480.-- All other amounts, including the $250 SSD, are allowances rather than verified purchase prices.--## Media--[45-second video](../media/video/MOSS_cost_comparison_20260921.mp4) · [Poster](../media/images/MOSS_cost_comparison_20260921.jpg) · [Media credits](../media/MOSS_cost_comparison_20260921_credits.md)--## 24 September update — V0.4 control components--The [ordered V0.4 control set](hardware_v04.md#control-electronics-ordered) is **$39.60 per rover**, including its optional snap-on enclosure, or **$34.65** without that enclosure. Two sets cost $79.20 plus $21.83 shipping; import charges are not included. The Cytron MDD3A is selected to replace the two MD10Cs; its purchase price is not supplied in this update.--The three totals above remain the **dated 21 September comparison**. Do not add the whole new order on top of a one-robot BOM: it contains two sets and replaces existing controller/INA lines. Recalculate a separate V0.4 total once all replacement lines, including the driver, are priced and reconciled.diff --git a/docs/bom.md b/docs/bom.mddeleted file mode 100644index f7eaf0f..0000000--- a/docs/bom.md+++ /dev/null@@ -1,78 +0,0 @@-# Bill of materials (work in progress)--The initial $500–700 target excluding the Jetson has been superseded by an [itemized comparison dated 21 September 2026](bom-costs.md): approximately **$1,680 for the Jetson / RealSense prototype configuration**, including an estimated $250 for its 2 TB SSD, and **$820 / $821 for experimental Pi 5 configurations** using Mighty Camera / ST 3D ToF and microSD storage.--These are planning budgets using replacement values for reused hardware, not a receipt total. Additional tax and shipping are not added. The Pi configurations are not yet navigation-tested; the hardware inventory below continues to describe the V0.3 prototype.--## Printed parts--The authoritative list is the [printed-parts inventory](printed_parts.md) (113 pieces in the V0.3 print set, per-part material, source file and print job; machine-readable copy in `printed_parts.json`). Summary by assembly:--| Assembly | Printed pieces | Notes |-|---|---:|---|-| Body (chassis, motor hatch, bin, cover) | 4 | chassis black PETG (H2S), bin and cover PLA |-| Tracks | 2 | TPU 95A, 0.4 mm nozzle profile (a 0.8 mm-nozzle print came out too stiff) |-| Side structure (inner and outer rails, cross spacers) | 8 | PETG |-| Ventilation (splash-proof vent covers) | 2 | PETG |-| Motor mounts | 2 | corrected revision Ø31 / M3 |-| Wheels and rollers | 20 | 2 drive wheels (4 halves), 2 idlers (4 halves), 6 road rollers (12 halves) |-| Tensioners and bearing retainers | 12 | |-| Drivetrain spacers | 32 | small spacers, distinct from the 4 cross spacers |-| Gaskets | 3 | TPU |-| Interior supports | 8 | including 4 Jetson base retainers |-| SO-101-derived arm | 8 | clips integrated in the arm parts |-| NC90 gripper (derived from the NormaCore parallel gripper) | 8 | rigid parts |-| Gripper pads | 2 | TPU |-| Camera brackets | 2 | RealSense D455 |-| **Total** | **113** | |--Not printed: metal HEX12 hubs, bearings, shaft collars, motor–shaft couplings, servo horns, fasteners.--## Electronics (as selected on 20 September 2026, after the first harness bench tests)-- Jetson Orin Nano Super 8 GB (brain), retaining its original plastic base; Wi-Fi on the Jetson side-- 2 TB SSD-- Intel RealSense D455 depth camera (RGB and IMU included)-- Espressif ESP32-S3-DevKitC-1 V1.1: motor controller (PWM/DIR for both drivers, both quadrature encoders, I²C to the INA219); see [`firmware/`](../firmware/README.md) for the wiring map-- 2 × Cytron MD10C R3 motor drivers-- 2 × geared DC motors with quadrature encoders-- Waveshare Bus Servo Adapter (A) V1.1: separate interface for the SO-101 arm servos (arm not tested yet)-- INA219 module at 0x40 (R100 = 0.1 Ω shunt): used for battery voltage only. In the tested wiring the motor current bypasses the shunt, so its current readings are not motor consumption. See the build log.-- Fuse holder with automotive blade fuse, 5 A (32 V DC) for the motor bench tests. The rating for the complete rover with Jetson and arm is not set yet; the pack's BMS thresholds are unknown.-- Positive distribution terminal block with ferrules; negative returns chained; XT60 to the pack-- 5 V buck converter for the logic, if needed (not installed)-- Removed from the design: Waveshare General Driver for Robots.--Cabling: same wire for the main runs and the driver branches, runs of 25–30 cm at most. Conductor bundle measured 1.2 mm in diameter; section estimated at 0.75–1 mm², not manufacturer-verified.--## V0.4 selection (next revision, not built)--The next revision selects a QT Py ESP32-S3 (5426), screw-terminal BFF (6495), optional enclosure (6505), INA219 STEMMA QT (904) and 300 mm cable (5384). One set is **$39.60** including the enclosure, before shipping and import charges. A Cytron MDD3A is selected to replace the two MD10Cs. The Waveshare Bus Servo Adapter remains.--See [the V0.4 update](hardware_v04.md) for quantities, unit prices, CAD status and remaining fit checks. This does not overwrite the as-built V0.3 inventory above. The new Adafruit INA footprint still needs reconciliation with the current hull model.--## Mechanical hardware-- Steel shafts 5 / 6 / 8 mm (cut to length)-- Bearings 608 and 626 (625 also in stock)-- Shaft collars 5 / 6 / 8 mm-- Rigid couplings 6 mm to 6 mm-- Fasteners M3 and M4--## Arm-- SO-101-derived arm: five ST3215 12 V joint servos-- NormaCore-derived parallel gripper: one CF35-12 constant-force servo-- This is the MOSS servo configuration, not the unmodified six-servo SO-101 kit BOM.----## Where to buy--Asked in a builders' group on 28 September: where do the parts come from. It depends on the part and on the distributors in your country; this is what works from Thailand.--- Original ESP32 microcontrollers made by Espressif: Mouser.-- RealSense: DigiKey.-- Tiny ESP32 boards for small form factors, ESP HATs with STEMMA QT plugs, QT cables, INA219 with QT: Adafruit.-- Raspberry Pi, Hailo HAT (AI accelerator), motor drivers: Cytron.-- Motors and sensors: a local supplier (Arduitronics in Thailand).-- Servo bus adapters and drivers for robots: Waveshare.-- Specialities such as the Mighty Cam SLAM camera or the ST VL53L9 time-of-flight board: from the manufacturer.-diff --git a/docs/build_log.md b/docs/build_log.mddeleted file mode 100644index bdba4c0..0000000--- a/docs/build_log.md+++ /dev/null@@ -1,148 +0,0 @@-# Build log--## 2026-09-15-Concept video V2.3.1 published. Target parts cost stated: 500 to 700 USD plus a Jetson.--## 2026-09-16-First prints started on two printers: the collection bin (PLA, Bambu Lab H2S) and a flexible track (TPU 95A, Bambu Lab P1S). Both finished the same evening.----## 2026-09-17-Two tracks, the bin and its top cover are done. The main chassis is printing in PETG on the H2S; the inner side rails and cross spacers on the P1S. Next plate: one outer side rail and two motor brackets. Shafts, bearings, collars, couplings and fasteners ordered.-----Video: `media/video/MOSS_build_update_20260917.mp4`.--## 2026-09-18-The main chassis came off the H2S in black PETG. First fit check on the bench: chassis, top cover, collection bin, the two flexible tracks, side rails and brackets. The RealSense sits up front, with access from above. Nothing is bolted yet; the parts go together with two or three small fit issues to correct in the next revision.------Printing now: the drivetrain, eight wheel halves (drive and idler wheels, 0.4 mm nozzle, black PETG, on the P1S), and a second plate of twelve parts, track tensioners and bearing retainers.-----Next: fit the drivetrain, mount the arm, test on the ground.--Video: `media/video/MOSS_build_log_02_20260918.mp4`.--## 2026-09-19 — V0.3 print set, assembly continues--The V0.3 prototype's print set is reported essentially complete: chassis and motor hatch, collection bin and cover, track structure, wheels and rollers, tensioners and spacers, interior supports, the SO-101-derived arm, the NC90 parallel gripper, gaskets and gripper pads. The [printed-parts inventory](printed_parts.md) reconciles the delivered print plans and records the remaining checks.--Two tracks have been printed in TPU 95A. The first has good flexibility and grip in manual floor tests. The second, printed with a 0.8 mm nozzle, is too stiff and will be reprinted. The successful 0.4 mm profile is the reference to preserve; the replacement is not yet reported complete.--The printed cover stays on this prototype. Closing the front around the offset arm plate is deferred to the next hardware revision. The complete-cover study is parked and is not part of this build.--Before calling the set fully reconciled, identify the corrected pair of motor brackets and locate the two RealSense mounting brackets: the latter exist in the CAD export but were not found in the final numbered print plates. This is a print and assembly update; it does not report a completed drive test or autonomous pickup.--Bench video of the print set laid out, 19 September (20 s pan): [MOSS_print_set_bench_20260919.mp4](../media/video/MOSS_print_set_bench_20260919.mp4). Stills: [print set](../media/images/build_print_set_bench_20260919.jpg), [electronics side](../media/images/build_electronics_bench_20260919.jpg) — bin and cover, rails, chassis, wheels, arm and gripper parts, the Jetson in its cartridge, motors and boards.--Next: replace the stiff track, assemble and check the drivetrain, fit the arm and electronics, and record the first powered tests when they happen.--## 2026-09-20 — power and control harness, first motor and encoder tests----The print set is complete, camera brackets and corrected motor brackets included, and the mechanical hardware (shafts, bearings, collars, couplings, fasteners) is in. The power and control harness is assembled. Both drive motors and their quadrature encoders were tested on the bench from an Espressif ESP32-S3-DevKitC-1 V1.1 driving two Cytron MD10C R3. Video: [MOSS_motor_encoder_bench_20260920.mp4](../media/video/MOSS_motor_encoder_bench_20260920.mp4); photo: [the harness on the bench](../media/images/build_harness_bench_20260920.jpg).--The selected architecture now uses the ESP32-S3 as motor controller and a separate Waveshare Bus Servo Adapter (A) V1.1 for the SO-101 arm servos. The Waveshare General Driver for Robots is no longer part of the design. The arm was not tested in this session. The ESP32 was powered over USB-UART during the tests; the motors from the pack through the fuse and the positive distribution block, with common grounds.--Firmware: [`firmware/`](../firmware/README.md), the source actually flashed after the tests (25 % commissioning limit). Wiring map in its README. Host logic test: `g++ -std=c++17 firmware/tests/control_test.cpp && ./a.out`.--### Results--| Test | Left encoder delta | Right encoder delta | Invalid transitions (L/R) |-|---|---:|---:|---:|-| Individual 15 % PWM, 1 s each | −704 | −712 | 0 / 0 |-| Both motors: positive 4 s ramp / 2 s at 100 % / 4 s ramp down | −38 083 | −38 609 | 0 / 0 |-| Both motors: negative 4 s ramp / 2 s at 100 % / 4 s ramp down | +40 340 | +41 679 | 1 / 2 |--Raw traces: [`hardware/bench/20260920/`](../hardware/bench/20260920/). Commanded and timed stops and the disarmed state were confirmed. Positive commands produced clockwise rotation seen from the rear of each motor, with negative tick counts. Forward direction and encoder signs still have to be set after the mirrored installation on the rover. The percentages are PWM duty, not a regulated speed. Tick counts are raw ×4 quadrature counts, not distance. The invalid-transition counters do not catch every possible encoder error.--The 100 % cycle used a temporary firmware; the 25 % limit was restored afterwards and further unloaded 25 % tests (left, right, both, 2 s) completed with no additional invalid transition. No loaded, stall, endurance or ground-driving test has been done.--### Battery monitoring--INA219 communication at 0x40 works and the pack read around 11.95–11.97 V: a voltage indication, not a calibrated state of charge nor per-cell monitoring. The module carries a 0.1 Ω R100 shunt, but in the tested wiring the motor current bypasses that shunt (the fuse-to-distribution link stays direct; the module's small terminal does not take the main cable). The currents in [`ina_bypassed_NOT_motor_current.json`](../hardware/bench/20260920/ina_bypassed_NOT_motor_current.json) are therefore not motor consumption and must not be used for fuse sizing, power claims or current protection. Decision: keep the INA219 for voltage only on this prototype. The firmware provides no battery undervoltage cutoff.--### Protection and cabling--Fuse for the motor bench tests: 5 A automotive blade, 32 V DC, same format as the holder. This is not the final rating for the rover with Jetson and arm; the pack's BMS thresholds are unknown. Cable runs of 25–30 cm at most; conductor bundle measured 1.2 mm in diameter, section estimated at 0.75–1 mm², not verified.--Next: integrate the harness into the chassis, set installed motor and encoder directions, measure ticks per revolution, then the Jetson interface and speed control. For the next hardware revision: mounts for the ESP32-S3, the servo adapter and the real distribution; the printed V0.3 stays the reference.--## 2026-09-20 (evening) — electronics in the chassis, Jetson on battery----First assembly of the electronics inside the printed chassis: motors, drivers, ESP32-S3, the pack in its bay, and the Jetson, which now boots from battery power. Video: [MOSS_first_assembly_20260920.mp4](../media/video/MOSS_first_assembly_20260920.mp4); still: [electronics in the chassis](../media/images/build_first_assembly_20260920.jpg).--First reality checks: some components ended up elsewhere than planned in CAD. The differences go into [assembly_feedback.md](assembly_feedback.md) as they are measured, and into the next hardware revision. No drive test yet.---## 2026-09-21 — cost comparison and alternative sensors ordered--Mighty Camera ($92 paid) and a STEVAL-VL53L9 evaluation board ($80 paid) were ordered to explore lower-cost navigation. The proposed computer is a Raspberry Pi 5 8 GB, budgeted at $175, with microSD storage. These are two alternative configurations, each retaining the tracked base and the MOSS arm and gripper. Navigation and detection on the Pi still need to be tested with dimOS.--The [new itemized budget](bom-costs.md) is $820 with Mighty or $821 with ST, compared with $1,676 for the Jetson / RealSense prototype configuration including a $250 allowance for its 2 TB SSD. These are replacement-cost planning figures, not actual expenditure. They supersede the initial $500–700 excluding Jetson target recorded on 15 September; that entry remains as history.--[Comparison video, 45 seconds](../media/video/MOSS_cost_comparison_20260921.mp4).--## 2026-09-22 — first drive------MOSS rolled for the first time today: tracks on, drivetrain assembled, the rover moving and turning on the floor under its own motors, still tethered for control. Video: [MOSS_first_drive_20260922.mp4](../media/video/MOSS_first_drive_20260922.mp4) (18 s).--What the first metres taught: the single-sided track adjustment leaves the tension uneven, so there is still some slack. Next hardware step: a second tensioner on each track. This is logged in [assembly_feedback.md](assembly_feedback.md).----The CAD already has the second tensioner on each track; one of them still lacks its adjustment screw, to be added next. No autonomous behaviour yet; this is a drive test.---## 2026-09-24 — V0.4 hull and simpler wiring--The physical prototype remains V0.3 and continues assembly and testing after its first drive. In parallel, V0.4 CAD now includes the revised hull and component arrangement: Jetson seat and USB-side cable space, compact motor driver and servo adapter, QT Py / terminal-block provision, a larger battery envelope and motor fasteners accessible from outside.--The V0.4 control electronics (QT Py ESP32-S3, Terminal Block BFF, INA219 STEMMA QT) are not installed yet. The INA model in CAD is approximate; the real board still needs a footprint and connector-fit check. Details and costs are in [the V0.4 update](hardware_v04.md).--A [40-second hardware-tour animation](../media/video/MOSS_V04_Inside_and_Action_20260924.mp4) shows the exterior leaving frame, an orbit of the hull and labelled components, reassembly and a scripted pickup. This is CAD animation; it does not report physical autonomous pickup or a new Jev experiment.--Remaining work includes the additional track tensioners, real connector fit, bin magnet mounts, wheel/roller screw recesses, new controller firmware mapping and physical V0.4 validation. The integrated lower platform beneath the arm is still fixed; making it detachable is deferred.--## 2026-09-24 (evening) — the simulator goes public, and MOSS runs in someone else's lab--The CPU MuJoCo simulator behind the Jev demo is now published in the demo repository, folder [`live/`](https://github.com/metrox-eth/moss-jev/tree/main/live): the MOSS body as a portable MJCF with its 57 visual meshes, the complete scene with the can, the three recorded Jev missions, and a replay command that needs no API key and no GPU. An [integration contract](https://github.com/metrox-eth/moss-jev/blob/main/live/INTEGRATION.md) gives units, frames, the eight actuators and the limits. Checked on Linux before publishing: 23 unit tests, the three missions (can, missed grasp, far can) finishing with the can settled in the bin, zero API calls.--Same day, a [V0.4 appearance overlay](https://github.com/metrox-eth/moss-jev/tree/main/live/model/visuals_v04) followed: the saved V0.4 hull, side assemblies and camera envelope, applied by a small script that keeps the host's masses, joints, cameras and contacts untouched. Two things to know if you import it. The CAD belts sit 266 mm apart while the legacy collision boxes are 244 mm apart; the overlay does not change the drive model, so a physically consistent V0.4 driving variant is still to do. And the visual meshes are decimated STL (5,000 to 6,000 triangles per part, no smoothed normals), which shows as facets in a renderer; a finer export is planned.--Numbers worth writing down while they are fresh, because a model copied often enough starts to look like a measurement. The physical prototype was weighed at 3.5 kg without the arm, cover (140 g) and bin (180 g) included, so about 3.18 kg bare. The 6.14 kg in the first MJCF export is an inertia computed from solid geometry, not a weighing. The camera's nominal front face sits at (156, 0, 75) mm in the rover frame, level; the 95 mm sometimes quoted is a mounting spacing, not its height. The reference SO-101 model totals 632 g; adding a 50 g allowance for the custom gripper gives about 682 g for the arm and gripper budget, or 4.18 kg including the measured base; the arm has not been weighed. The vertical centre of gravity, 75 mm, is estimated, and the "CG above the middle roller" observation was made without cover, bin or arm, so it does not apply to a loaded bin.--Within the day, another lab imported the body into its own simulator and started training a can-scooping policy by reinforcement learning on it, 32 environments in parallel. The base in our model is a simplified slide, not tracked-ground dynamics; that limitation is theirs to work around too.---## 2026-09-26 — arm and gripper on the V0.3, V0.4 parts printing--The arm is on the rover, gripper included. It is a standard SO-101 so far; the only change is a pair of clips for the USB camera cable. The idea stays: if you already have an SO-101, you can use yours in the build.------Two things learned by looking at it on the floor. The track chevrons point the wrong way for traction on this rover, so the tracks will be flipped. And a reader noticed that the second joint from the base, the shoulder, looks weak for a load-bearing joint. That is now [issue #2](https://github.com/metrox-eth/moss/issues/2), meant as a first contribution: check the load in the CAD, then propose either a dual-servo shoulder like the RoArm-M3 or a stronger bracket on the existing servo.--Weighed on 27 September, arm and gripper together, off the rover: 768 g. The 24 September note estimated 682 g from the reference SO-101 model plus a gripper allowance, so the estimate was 86 g light. Added to the base as weighed on 24 September (3.5 kg without the arm), that gives about 4.27 kg for the loaded rover, a sum, not a weighing; the assembled rover gets its own weighing once it is on the V0.4 hull. Part of the extra mass is the servos: this prototype's arm runs ST3235 salvaged from older arms, heavier than the ST3215 the parts list recommends; builders should take the ST3215.--The V0.4 print set has started. Asked the same day what eats the budget: the onboard computer and the perception sensors, by far. The Raspberry Pi version exists to bring that line down; the numbers are in the [itemized budget](bom-costs.md).--A team in the Netherlands building a larger, autonomous litter-picking robot got in touch. More when there is something concrete.diff --git a/docs/concept.md b/docs/concept.mddeleted file mode 100644index 478fedf..0000000--- a/docs/concept.md+++ /dev/null@@ -1,17 +0,0 @@-# Concept--MOSS is a litter-picking rover for sidewalks, roadsides and parks: small enough to print, cheap enough to build several, useful enough to keep.------- Tracked base (two motors with encoders, differential drive), printed tracks in TPU.-- Collection bin on top, emptied by hand at the end of a run.-- Arm derived from the SO-101 (6 DoF, open source) with a NormaCore parallel gripper.-- Current compute and perception: Jetson Orin Nano Super 8 GB, 2 TB SSD and RealSense D455. The intended compute cartridge is modular; the first prototype placement has changed during assembly. A lower-cost Raspberry Pi 5 build with alternative navigation sensors is being explored, starting with teleop and then testing dimOS navigation. [Budget and integration work](bom-costs.md).-- Software: dimOS for navigation and teleop, LeRobot for data and policies.--The criterion we use for success: pick up more litter with less technology. Every added part has to earn its place against a person with a bag.--Concept video (V2.3.1, 15 September 2026): `media/video/MOSS_V2_3_1_20260915.mp4` (concept simulation, scripted robot; not a demo of a working policy). The chassis in that video is an earlier revision; the current one, in the exploded view at the top of the README, has the same shape with track tensioners added.diff --git a/docs/hardware_v04.md b/docs/hardware_v04.mddeleted file mode 100644index 154a793..0000000--- a/docs/hardware_v04.md+++ /dev/null@@ -1,63 +0,0 @@-# Hardware V0.4 — development update--24 September 2026. The physical rover remains **V0.3**. **V0.4** is the next hardware revision, being developed from assembly feedback while the existing prototype is tested. It is not yet a printed, assembled or qualified replacement.--## Control electronics ordered--Two of each item below were ordered, providing two sets. Quantities in the first numeric column are for one rover. Prices are the builder's order prices, not a complete robot cost.--| Item | Per rover | Ordered | Unit USD |-|---|---:|---:|---:|-| [QT Py ESP32-S3, 8 MB Flash / no PSRAM, PID 5426](https://www.adafruit.com/product/5426) | 1 | 2 | 12.50 |-| [Terminal Block BFF, PID 6495](https://www.adafruit.com/product/6495) | 1 | 2 | 10.95 |-| [Snap-on enclosure, PID 6505](https://www.adafruit.com/product/6505) | 1 optional | 2 | 4.95 |-| [INA219 STEMMA QT, PID 904](https://www.adafruit.com/product/904) | 1 | 2 | 9.95 |-| [STEMMA QT / Qwiic JST-SH cable, 300 mm, PID 5384](https://www.adafruit.com/product/5384) | 1 | 2 | 1.25 |-| **One set, including enclosure** | | | **39.60** |--Two sets: **$79.20** in parts, **$21.83** shipping, **$101.03** order total before any separately collected import charges. Without the optional enclosure the parts used in one integrated hull cost **$34.65**. This is a control-electronics subtotal, not a revised total BOM.--The BFF provides screw terminals for the harness. Headers still need soldering to the QT Py; the wires themselves terminate in connectors or screw terminals. One STEMMA QT cable connects each INA219 to its controller. The QT Py and BFF have different I2C pin routes on this ESP32-S3 variant, so the firmware must match the connector actually used. The old DevKitC pin numbers are not a drop-in QT Py wiring map.--The INA219 remains a **battery-voltage monitor** in the present design. Its stock shunt measurement range is ±3.2 A; this update does not put the complete rover current through it or validate current-based battery monitoring.--Ordered is not received or tested. The existing V0.3 wiring and firmware remain the reference for the physical prototype until the new electronics are fitted and tested.--## Other selected changes--- One **Cytron MDD3A dual-channel driver**, ordered earlier, is selected to replace the two MD10C drivers in V0.4. The first-drive prototype still uses the MD10Cs. The MDD3A has not been validated on MOSS in this update; its purchase price is not supplied here.-- The **Waveshare Bus Servo Adapter (A) V1.1** remains the separate SO-101 servo interface. The General Driver for Robots is already removed from the selected architecture.-- A **30 cm USB-A to right-angle USB-C cable** is ordered for the RealSense D455f. USB3 operation and the actual plug envelope remain to be tested at delivery.-- Panel-mount **5.5 × 2.1 mm DC jack** selected for the charging connection. The supplied DC-022B drawing specifies an M8 × 1 mounting barrel. This is a connector provision, not a charging circuit.-- Four **40 × 10 × 5 mm magnets** are ordered to retain the bin. Their mounting pockets and retention arrangement are still to be designed.-- The fuse remains in the power path, in an **inline cable holder**. Removing the separate printed fuse-holder mount does not remove electrical protection or establish a final fuse rating.--## Current hull CAD--The latest local assembly is named `MOSS_Hull_V04_Cartes_INA90.step`. It includes the hull, electronics, battery envelope, motor supports and motor reference models. Its companion hull-only STEP/STL is `MOSS_hull_V04_cartes_INA90`.--- Jetson retains its original plastic base. The removable caddy is replaced by an integrated seat and retaining pieces, with a cable route on the USB side.-- Integrated mounting provision for the QT Py / BFF. The purchased snap-on enclosure is optional and is not the mounting interface used in this hull CAD.-- Cytron and Waveshare positions have been exchanged. The Waveshare is rotated 90 degrees for USB access; the INA219 and its mounting features are also rotated 90 degrees for wiring access.-- The existing battery measures **67 × 74 × 27 mm**. The blue **75 × 82 × 32 mm** volume is a candidate larger-pack envelope only, with wire and XT connector space. It establishes neither a purchased battery nor capacity or runtime.-- The **lower platform integrated into the hull beneath the arm** is still fixed. Making it detachable has been deferred.-- Motor-support fastening is designed from the outside through recessed M4 heads in the hull into captive M4 nuts in the supports. The local study uses standard M4 × 20 screws; final assembly access and printed fit still need validation.--The latest hull export passed local solid/mesh and clearance checks. Those checks are not physical assembly validation. The INA reference is an approximate model of the **existing module**, not proof of fit for the newly ordered Adafruit board. Its footprint, mount positions and STEMMA connectors must be reconciled before printing that revision. The motor reference model also does not certify the actual motor screw pattern or encoder/cable clearance.--Only the hull and explicitly requested component placements were advanced in this work. Unrelated printed parts were not silently replaced. The manufacturing files are still awaiting release review.--## Assembly feedback still to close--- Fit the second tensioner on each track and validate even tension. A track shortened by one tooth is a candidate for testing, not a validated new belt length.-- Add screw-head recesses in wheels and rollers.-- Use commonly available screw lengths and head types; do not require custom 26 mm screws or routine screw shortening in the released design.-- Keep the corrected flank geometry. The suspected tensioner conflict was partly due to trying the wrong rail; do not relocate the fourth fixing solely on that initial diagnosis.-- Validate the more continuous front cover / hull interface separately. No replacement cover is being released by this hull update.-- Finish the bin magnet retention, new INA mounting, real connector fit and the electronics/firmware migration before calling the V0.4 BOM reproducible.--## Animation--[V0.4 hardware tour and pickup animation](../media/video/MOSS_V04_Inside_and_Action_20260924.mp4) — 40 seconds, 1920 × 1080, 30 fps, silent.--The exterior moves out of frame, the camera orbits the current hull and components with readable labels, then the rover reassembles, rolls and picks up a can. This is a **scripted CAD presentation**, not footage of autonomous pickup, a Jev run or a new physical test. Exterior geometry is reused from the previous exploded view; the interior reflects the saved V0.4 assembly. The separate Jev / MuJoCo demo is unchanged.diff --git a/docs/lessons.md b/docs/lessons.mdnew file mode 100644index 0000000..541fae4--- /dev/null+++ b/docs/lessons.md@@ -0,0 +1,15 @@+# What we learned the hard way++One line each. What happened, and what it changes for you.++1. **Print the tracks with a 0.4 mm nozzle.** The 0.8 mm nozzle makes them too stiff to run. The track profile that works is shipped with the files.+2. **One tensioner per track is not enough.** The first drive showed uneven tension and slack. V0.5 has two per side; fit both.+3. **No jumper wires on a rover.** Dupont connections made false contacts once the rover moved. The controller sits on a screw-terminal board.+4. **The INA219 reads voltage, not motor current.** The shunt was never in the motor line. Do not read its current field as if it were.+5. **Motor-mount screws need access from outside.** We drilled through the hull after assembly. The mounts now have exterior-access heads.+6. **Standard screw lengths only.** No custom cutting. The fastener list is in the [BOM](../BOM.md).+7. **The RealSense needs a right-angle USB cable.** The straight plug does not clear the hull. The cable is a line in the BOM.+8. **Small magnets are enough for the bin.** 20 × 10 × 2 mm, two in the cover, two in the bin.+9. **The arm had to move to make room for the lidar and clear the bin.** Keep the arm plate where the CAD puts it; the elbow already touches the bin when the arm is folded.+10. **Weigh the real robot before trusting the model.** The prototype came in at 3.5 kg without the arm; the first simulator export said 6.14 kg. A number copied often enough starts to look like a measurement.+11. **Put the rover on blocks for the first run.** Every time the firmware or the wiring changes.diff --git a/docs/printed_parts.json b/docs/printed_parts.jsondeleted file mode 100644index e126e68..0000000--- a/docs/printed_parts.json+++ /dev/null@@ -1,1101 +0,0 @@-{- "as_of": "2026-09-20",- "repository": "https://github.com/metrox-eth/moss",- "reviewed_commit": "d22c513c2d5f866f8da212f4962d24a594859de1",- "basis": "Print set complete per the builder on 20 September 2026. Quantities reconstructed from the final print plans.",- "parts": [- {- "group": "Body",- "part": "Main chassis / hull",- "quantity": 1,- "material": "Black PETG",- "source_file": "Carter_PETG_continu_-_revision_mecanique_R8.stl",- "print_job": "Standalone H2S chassis",- "status": "printed",- "note": ""- },- {- "group": "Body",- "part": "Motor access hatch",- "quantity": 1,- "material": "Black PETG",- "source_file": "Trappe_inferieure_acces_moteurs_R8.stl",- "print_job": "Standalone hatch",- "status": "printed",- "note": "R8 export reference; the precise revision of the physical hatch is not recorded."- },- {- "group": "Body",- "part": "Collection bin",- "quantity": 1,- "material": "Blue PLA",- "source_file": "MOSS_bac_corrige.stl",- "print_job": "Standalone H2S bin",- "status": "printed",- "note": ""- },- {- "group": "Body",- "part": "Existing top cover R5",- "quantity": 1,- "material": "Blue PLA",- "source_file": "MOSS_capot_monobloc_H2S_R5.stl",- "print_job": "Standalone H2S cover",- "status": "printed",- "note": "Keep the printed prototype cover. The unfinished front interface remains as-is; full-cover redesign is parked."- },- {- "group": "Tracks",- "part": "Continuous track R2",- "quantity": 2,- "material": "TPU 95A",- "source_file": "MOSS_chenille_TPU95A_P1S_R2.stl",- "print_job": "Standalone P1S tracks, 0.4 mm nozzle",- "status": "printed",- "note": "A print made with a 0.8 mm nozzle came out too stiff and is not used; the 0.4 mm profile is the reference."- },- {- "group": "Side structure",- "part": "R8 G Entretoise traverse -40",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_traverse_-40_R8.stl",- "print_job": "01 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 G Entretoise traverse 40",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_traverse_40_R8.stl",- "print_job": "01 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 G Flanc interieur",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Flanc_interieur_R8.stl",- "print_job": "01 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 D Entretoise traverse -40",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_traverse_-40_R8.stl",- "print_job": "01 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 D Entretoise traverse 40",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_traverse_40_R8.stl",- "print_job": "01 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 D Flanc interieur",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Flanc_interieur_R8.stl",- "print_job": "01 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 G Flanc exterieur",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Flanc_exterieur_R8.stl",- "print_job": "02 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Side structure",- "part": "R8 D Flanc exterieur",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Flanc_exterieur_R8.stl",- "print_job": "03 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Ventilation",- "part": "Entree air sous carter - chicane demontable",- "quantity": 1,- "material": "Black PETG",- "source_file": "Entree_air_sous_carter_-_chicane_demontable_R8.stl",- "print_job": "03 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Ventilation",- "part": "Extraction air sous carter - chicane demontable",- "quantity": 1,- "material": "Black PETG",- "source_file": "Extraction_air_sous_carter_-_chicane_demontable_R8.stl",- "print_job": "03 — P1S 0.8",- "status": "printed",- "note": ""- },- {- "group": "Motor mounts",- "part": "Corrected motor bracket G V2-01",- "quantity": 1,- "material": "Black PETG",- "source_file": "MOSS_support_moteur_G_V2_01.stl",- "print_job": "Standalone correction — P1S 0.4",- "status": "printed",- "note": "Replaces the original plate-02 bracket; count once in the current build. Corrected Ø31 mm / M3 pattern; screw depth to check at assembly."- },- {- "group": "Motor mounts",- "part": "Corrected motor bracket D V2-01",- "quantity": 1,- "material": "Black PETG",- "source_file": "MOSS_support_moteur_D_V2_01.stl",- "print_job": "Standalone correction — P1S 0.4",- "status": "printed",- "note": "Replaces the original plate-02 bracket; count once in the current build. Corrected Ø31 mm / M3 pattern; screw depth to check at assembly."- },- {- "group": "Wheels and rollers",- "part": "R8_D_Roue_tendeuse_22d_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Roue_tendeuse_22d_demi-exterieure_R8.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Roue_tendeuse_22d_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Roue_tendeuse_22d_demi-interieure_R8.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Roue_tendeuse_22d_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Roue_tendeuse_22d_demi-exterieure_R8.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Roue_tendeuse_22d_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Roue_tendeuse_22d_demi-interieure_R8.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8H_D_Roue_motrice_HEX12_demi_exterieure",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8H_D_Roue_motrice_HEX12_demi_exterieure.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8H_D_Roue_motrice_HEX12_demi_interieure",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8H_D_Roue_motrice_HEX12_demi_interieure.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8H_G_Roue_motrice_HEX12_demi_exterieure",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8H_G_Roue_motrice_HEX12_demi_exterieure.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8H_G_Roue_motrice_HEX12_demi_interieure",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8H_G_Roue_motrice_HEX12_demi_interieure.stl",- "print_job": "04A — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Galet625_-70_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Galet625_-70_demi-exterieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Galet625_-70_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Galet625_-70_demi-interieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Galet625_0_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Galet625_0_demi-exterieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Galet625_0_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Galet625_0_demi-interieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Galet625_70_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Galet625_70_demi-exterieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_D_Galet625_70_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Galet625_70_demi-interieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Galet625_-70_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Galet625_-70_demi-exterieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Galet625_-70_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Galet625_-70_demi-interieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Galet625_0_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Galet625_0_demi-exterieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Galet625_0_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Galet625_0_demi-interieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Galet625_70_demi-exterieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Galet625_70_demi-exterieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Wheels and rollers",- "part": "R8_G_Galet625_70_demi-interieure_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Galet625_70_demi-interieure_R8.stl",- "print_job": "04B — P1S 0.4; replaces 04 H2S",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_D_Couvercle_tendeur_exterieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Couvercle_tendeur_exterieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_D_Couvercle_tendeur_interieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Couvercle_tendeur_interieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_G_Couvercle_tendeur_exterieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Couvercle_tendeur_exterieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_G_Couvercle_tendeur_interieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Couvercle_tendeur_interieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_D_Coulisseau_exterieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Coulisseau_exterieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_D_Coulisseau_interieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Coulisseau_interieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_G_Coulisseau_exterieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Coulisseau_exterieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_G_Coulisseau_interieur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Coulisseau_interieur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_D_Couvercle_palier_moteur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Couvercle_palier_moteur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "R8_G_Couvercle_palier_moteur_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Couvercle_palier_moteur_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "Retenue_interieure_roulement_-1_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "Retenue_interieure_roulement_-1_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Tensioners and bearing retainers",- "part": "Retenue_interieure_roulement_1_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "Retenue_interieure_roulement_1_R8.stl",- "print_job": "05 — H2S 0.4",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_-70_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_-70_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_-70_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_-70_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_-70_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_-70_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_0_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_0_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_0_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_0_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_0_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_0_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_70_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_70_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_70_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_70_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_galet_70_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_galet_70_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_tendeur_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_tendeur_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_tendeur_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_tendeur_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_tendeur_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_tendeur_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_tendeur_retenue_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_tendeur_retenue_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_tendeur_retenue_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_tendeur_retenue_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_-70_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_-70_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_-70_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_-70_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_-70_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_-70_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_0_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_0_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_0_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_0_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_0_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_0_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_70_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_70_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_70_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_70_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_galet_70_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_galet_70_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_tendeur_centrale_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_tendeur_centrale_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_tendeur_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_tendeur_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_tendeur_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_tendeur_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_tendeur_retenue_externe_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_tendeur_retenue_externe_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_tendeur_retenue_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_tendeur_retenue_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_D_Entretoise_motrice_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_D_Entretoise_motrice_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8_G_Entretoise_motrice_interne_R8",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8_G_Entretoise_motrice_interne_R8.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8H_D_Entretoise_motrice_externe_HEX12_L15_6",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8H_D_Entretoise_motrice_externe_HEX12_L15_6.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Drivetrain spacers",- "part": "R8H_G_Entretoise_motrice_externe_HEX12_L15_6",- "quantity": 1,- "material": "Black PETG",- "source_file": "R8H_G_Entretoise_motrice_externe_HEX12_L15_6.stl",- "print_job": "06 — P1S 0.4; replaces 06 H2S",- "status": "printed",- "note": ""- },- {- "group": "Gaskets",- "part": "Joint_trappe_moteurs_R8",- "quantity": 1,- "material": "TPU 95A",- "source_file": "Joint_trappe_moteurs_R8.stl",- "print_job": "07 joints — H2S 0.4",- "status": "printed",- "note": "R8 gasket source; fit to assembled interfaces remains to be checked."- },- {- "group": "Gaskets",- "part": "Joint_sous_platine_-_appui_continu_R8",- "quantity": 1,- "material": "TPU 95A",- "source_file": "Joint_sous_platine_-_appui_continu_R8.stl",- "print_job": "07 joints — H2S 0.4",- "status": "printed",- "note": "R8 gasket source; fit to assembled interfaces remains to be checked."- },- {- "group": "Gaskets",- "part": "R8_CAMERA_Joint_facade_D455_R8",- "quantity": 1,- "material": "TPU 95A",- "source_file": "R8_CAMERA_Joint_facade_D455_R8.stl",- "print_job": "07 joints — H2S 0.4",- "status": "printed",- "note": "R8 gasket source; fit to assembled interfaces remains to be checked."- },- {- "group": "Interior supports",- "part": "Berceau_electronique_R11",- "quantity": 1,- "material": "Black PLA",- "source_file": "Berceau_electronique_R11.stl",- "print_job": "07A_berceau_PLA_noir",- "status": "printed",- "note": ""- },- {- "group": "Interior supports",- "part": "Support_porte_fusible_R9",- "quantity": 1,- "material": "Black PLA",- "source_file": "Support_porte_fusible_R9.stl",- "print_job": "07A_berceau_PLA_noir",- "status": "printed",- "note": ""- },- {- "group": "Interior supports",- "part": "Platine_bras_R11",- "quantity": 1,- "material": "Black PLA",- "source_file": "Platine_bras_R11.stl",- "print_job": "07B_platine_PLA_noir",- "status": "printed",- "note": "Replacement arm plate, not an additional plate stacked on top of R8/R9."- },- {- "group": "Interior supports",- "part": "Retenue_socle_Jetson_R11",- "quantity": 4,- "material": "Black PLA",- "source_file": "Retenue_socle_Jetson_R11.stl",- "print_job": "07B_platine_PLA_noir",- "status": "printed",- "note": ""- },- {- "group": "Interior supports",- "part": "Plateau_Jetson_R11",- "quantity": 1,- "material": "Black PLA",- "source_file": "Plateau_Jetson_R11.stl",- "print_job": "07C_Jetson_PLA_noir",- "status": "printed",- "note": ""- },- {- "group": "SO-101 arm",- "part": "SO101_Bras_superieur_clip",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Bras_superieur_clip.stl",- "print_job": "08_bras_PLA_saumon_01",- "status": "printed",- "note": "Four cable clips are integrated into arm parts; no additional printed clip count."- },- {- "group": "SO-101 arm",- "part": "SO101_Avant_bras_clip",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Avant_bras_clip.stl",- "print_job": "08_bras_PLA_saumon_01",- "status": "printed",- "note": "Four cable clips are integrated into arm parts; no additional printed clip count."- },- {- "group": "SO-101 arm",- "part": "SO101_Base",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Base.stl",- "print_job": "08_bras_PLA_saumon_01",- "status": "printed",- "note": ""- },- {- "group": "SO-101 arm",- "part": "SO101_Rotation_epaule",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Rotation_epaule.stl",- "print_job": "08_bras_PLA_saumon_01",- "status": "printed",- "note": ""- },- {- "group": "SO-101 arm",- "part": "SO101_Support_epaule_clip",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Support_epaule_clip.stl",- "print_job": "08_bras_PLA_saumon_01",- "status": "printed",- "note": "Four cable clips are integrated into arm parts; no additional printed clip count."- },- {- "group": "SO-101 arm",- "part": "SO101_Base_motor_holder",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Base_motor_holder.stl",- "print_job": "08_bras_PLA_saumon_02",- "status": "printed",- "note": ""- },- {- "group": "SO-101 arm",- "part": "SO101_Poignet_clip",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Poignet_clip.stl",- "print_job": "08_bras_PLA_saumon_02",- "status": "printed",- "note": "Four cable clips are integrated into arm parts; no additional printed clip count."- },- {- "group": "SO-101 arm",- "part": "SO101_Support_poignet",- "quantity": 1,- "material": "PLA — salmon in print plan",- "source_file": "SO101_Support_poignet.stl",- "print_job": "08_bras_PLA_saumon_02",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Corps_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Corps_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Machoire_gauche_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Machoire_gauche_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Machoire_droite_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Machoire_droite_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Support_camera_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Support_camera_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Flasque_1_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Flasque_1_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Flasque_2_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Flasque_2_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Pignon_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Pignon_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "NormaCore gripper",- "part": "Guide_cable_NC90",- "quantity": 1,- "material": "PLA — turquoise in print plan",- "source_file": "Guide_cable_NC90.stl",- "print_job": "09_pince_PLA_turquoise",- "status": "printed",- "note": ""- },- {- "group": "Gripper pads",- "part": "Patin_TPU_gauche",- "quantity": 1,- "material": "TPU 95A",- "source_file": "Patin_TPU_gauche.stl",- "print_job": "10_patins_TPU95A",- "status": "printed",- "note": ""- },- {- "group": "Gripper pads",- "part": "Patin_TPU_droit",- "quantity": 1,- "material": "TPU 95A",- "source_file": "Patin_TPU_droit.stl",- "print_job": "10_patins_TPU95A",- "status": "printed",- "note": ""- },- {- "group": "Camera brackets",- "part": "D455 camera mounting bracket -1",- "quantity": 1,- "material": "PETG",- "source_file": "R8_CAMERA_Equerre_D455_-1_R8.stl",- "print_job": "Standalone",- "status": "printed",- "note": "RealSense D455 mounting bracket."- },- {- "group": "Camera brackets",- "part": "D455 camera mounting bracket 1",- "quantity": 1,- "material": "PETG",- "source_file": "R8_CAMERA_Equerre_D455_1_R8.stl",- "print_job": "Standalone",- "status": "printed",- "note": "RealSense D455 mounting bracket."- }- ],- "scope": "Prototype inventory only. No CAD/STL release approval or physical fit certification. Duplicate formats, superseded plates and failed/rejected designs excluded.",- "prototype_version": "V0.3",- "printed_units": 113-}diff --git a/docs/printed_parts.md b/docs/printed_parts.mddeleted file mode 100644index f7563f2..0000000--- a/docs/printed_parts.md+++ /dev/null@@ -1,256 +0,0 @@-# MOSS V0.3 — prototype printed-parts inventory--Updated: **20 September 2026**.--The V0.3 print set is complete: **113 pieces**, reconciled from the final print plans. Quantities are assembly requirements, not the cumulative number of prints, failed attempts or spares.--`printed` means the part exists; fit and load checks happen at assembly and are logged in [assembly_feedback.md](assembly_feedback.md).--## Current print feedback--- Tracks in TPU 95A: the 0.4 mm-nozzle print has good flexibility and floor grip in a manual test. A print made with a 0.8 mm nozzle came out too stiff and is not used.-- Preserve the successful 0.4 mm print profile as the reference. Record nozzle, extrusion width, walls, layer height, infill and material together; the two prints do not isolate nozzle diameter as the only cause.-- The prototype front cover remains unfinished around the offset arm plate. The complete-cover redesign is parked for the next hardware revision and is excluded below.--## Reconciled quantities--| Assembly | Printed pieces |-|---|---:|-| Body | 4 |-| Tracks | 2 |-| Side structure | 8 |-| Ventilation | 2 |-| Motor mounts | 2 |-| Wheels and rollers | 20 |-| Tensioners and bearing retainers | 12 |-| Drivetrain spacers | 32 |-| Gaskets | 3 |-| Interior supports | 8 |-| SO-101 arm | 8 |-| NormaCore gripper | 8 |-| Gripper pads | 2 |-| **Total in the print plan** | **111** |--This includes 2 drive wheels made from 4 halves, 2 idler wheels made from 4 halves, 6 road rollers made from 12 halves, 32 small drivetrain spacers and 4 cross spacers. Metal hubs, bearings, shaft collars, servo horns and fasteners are not printed parts.--## Detailed inventory--G/D and −1/+1 retain the CAD naming so parts can be matched to their source files. Colour is taken from the print plan unless directly reported; no exact spool brand is inferred. Source filenames identify workshop revisions and are not download links or approved public releases.--### Body--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `Carter_PETG_continu_-_revision_mecanique_R8.stl` | 1 | Black PETG | Standalone H2S chassis | printed |-| `Trappe_inferieure_acces_moteurs_R8.stl` | 1 | Black PETG | Standalone hatch | printed |-| `MOSS_bac_corrige.stl` | 1 | Blue PLA | Standalone H2S bin | printed |-| `MOSS_capot_monobloc_H2S_R5.stl` | 1 | Blue PLA | Standalone H2S cover | printed |--- R8 export reference; the precise revision of the physical hatch is not recorded.-- Keep the printed prototype cover. The unfinished front interface remains as-is; full-cover redesign is parked.--### Tracks--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `MOSS_chenille_TPU95A_P1S_R2.stl` | 2 | TPU 95A | Standalone P1S tracks, 0.4 mm nozzle | printed |--- A track printed with a 0.8 mm nozzle came out too stiff and is not used; the 0.4 mm profile is the reference.--### Side structure--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `R8_G_Entretoise_traverse_-40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |-| `R8_G_Entretoise_traverse_40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |-| `R8_G_Flanc_interieur_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |-| `R8_D_Entretoise_traverse_-40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |-| `R8_D_Entretoise_traverse_40_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |-| `R8_D_Flanc_interieur_R8.stl` | 1 | Black PETG | 01 — P1S 0.8 | printed |-| `R8_G_Flanc_exterieur_R8.stl` | 1 | Black PETG | 02 — P1S 0.8 | printed |-| `R8_D_Flanc_exterieur_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | printed |--### Ventilation--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `Entree_air_sous_carter_-_chicane_demontable_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | printed |-| `Extraction_air_sous_carter_-_chicane_demontable_R8.stl` | 1 | Black PETG | 03 — P1S 0.8 | printed |--### Motor mounts--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `MOSS_support_moteur_G_V2_01.stl` | 1 | Black PETG | Standalone correction — P1S 0.4 | printed |-| `MOSS_support_moteur_D_V2_01.stl` | 1 | Black PETG | Standalone correction — P1S 0.4 | printed |--- Replaces the original plate-02 bracket; count once in the current build. Corrected Ø31 mm / M3 pattern; screw depth to check at assembly.--### Wheels and rollers--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `R8_D_Roue_tendeuse_22d_demi-exterieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Roue_tendeuse_22d_demi-interieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Roue_tendeuse_22d_demi-exterieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Roue_tendeuse_22d_demi-interieure_R8.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8H_D_Roue_motrice_HEX12_demi_exterieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8H_D_Roue_motrice_HEX12_demi_interieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8H_G_Roue_motrice_HEX12_demi_exterieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8H_G_Roue_motrice_HEX12_demi_interieure.stl` | 1 | Black PETG | 04A — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Galet625_-70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Galet625_-70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Galet625_0_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Galet625_0_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Galet625_70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_D_Galet625_70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Galet625_-70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Galet625_-70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Galet625_0_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Galet625_0_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Galet625_70_demi-exterieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |-| `R8_G_Galet625_70_demi-interieure_R8.stl` | 1 | Black PETG | 04B — P1S 0.4; replaces 04 H2S | printed |--### Tensioners and bearing retainers--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `R8_D_Couvercle_tendeur_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_D_Couvercle_tendeur_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_G_Couvercle_tendeur_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_G_Couvercle_tendeur_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_D_Coulisseau_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_D_Coulisseau_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_G_Coulisseau_exterieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_G_Coulisseau_interieur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_D_Couvercle_palier_moteur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `R8_G_Couvercle_palier_moteur_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `Retenue_interieure_roulement_-1_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |-| `Retenue_interieure_roulement_1_R8.stl` | 1 | Black PETG | 05 — H2S 0.4 | printed |--### Drivetrain spacers--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `R8_D_Entretoise_galet_-70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_-70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_-70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_0_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_0_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_0_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_galet_70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_tendeur_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_tendeur_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_tendeur_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_tendeur_retenue_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_tendeur_retenue_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_-70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_-70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_-70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_0_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_0_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_0_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_70_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_70_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_galet_70_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_tendeur_centrale_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_tendeur_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_tendeur_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_tendeur_retenue_externe_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_tendeur_retenue_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_D_Entretoise_motrice_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8_G_Entretoise_motrice_interne_R8.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8H_D_Entretoise_motrice_externe_HEX12_L15_6.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |-| `R8H_G_Entretoise_motrice_externe_HEX12_L15_6.stl` | 1 | Black PETG | 06 — P1S 0.4; replaces 06 H2S | printed |--### Gaskets--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `Joint_trappe_moteurs_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | printed |-| `Joint_sous_platine_-_appui_continu_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | printed |-| `R8_CAMERA_Joint_facade_D455_R8.stl` | 1 | TPU 95A | 07 joints — H2S 0.4 | printed |--- R8 gasket source; fit to assembled interfaces remains to be checked.--### Interior supports--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `Berceau_electronique_R11.stl` | 1 | Black PLA | 07A_berceau_PLA_noir | printed |-| `Support_porte_fusible_R9.stl` | 1 | Black PLA | 07A_berceau_PLA_noir | printed |-| `Platine_bras_R11.stl` | 1 | Black PLA | 07B_platine_PLA_noir | printed |-| `Retenue_socle_Jetson_R11.stl` | 4 | Black PLA | 07B_platine_PLA_noir | printed |-| `Plateau_Jetson_R11.stl` | 1 | Black PLA | 07C_Jetson_PLA_noir | printed |--- Replacement arm plate, not an additional plate stacked on top of R8/R9.--### SO-101 arm--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `SO101_Bras_superieur_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |-| `SO101_Avant_bras_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |-| `SO101_Base.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |-| `SO101_Rotation_epaule.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |-| `SO101_Support_epaule_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_01 | printed |-| `SO101_Base_motor_holder.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | printed |-| `SO101_Poignet_clip.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | printed |-| `SO101_Support_poignet.stl` | 1 | PLA — salmon in print plan | 08_bras_PLA_saumon_02 | printed |--- Four cable clips are integrated into arm parts; no additional printed clip count.--### NormaCore gripper--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `Corps_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Machoire_gauche_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Machoire_droite_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Support_camera_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Flasque_1_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Flasque_2_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Pignon_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |-| `Guide_cable_NC90.stl` | 1 | PLA — turquoise in print plan | 09_pince_PLA_turquoise | printed |--### Gripper pads--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `Patin_TPU_gauche.stl` | 1 | TPU 95A | 10_patins_TPU95A | printed |-| `Patin_TPU_droit.stl` | 1 | TPU 95A | 10_patins_TPU95A | printed |--### Camera brackets--| Part / source STL | Qty | Material | Plate / job | Status |-|---|---:|---|---|---|-| `R8_CAMERA_Equerre_D455_-1_R8.stl` | 1 | PETG | Standalone | printed |-| `R8_CAMERA_Equerre_D455_1_R8.stl` | 1 | PETG | Standalone | printed |--## Superseded or excluded--- Original R8 motor brackets from plate 02: replaced by V2-01. Do not count both pairs as current parts.-- Original drive-wheel interfaces: use R8H HEX12 wheel halves and the corresponding external 15.6 mm spacers. The motor-to-shaft couplings are separate metal hardware.-- H2S wheel plate 04: superseded by P1S plates 04A and 04B. H2S spacer plate 06: superseded by P1S plate 06.-- Old R8/R9 arm plate and Jetson support: use the R11 print set; four Jetson-base retainers are included.-- The four arm cable clips are integrated into SO-101 printed pieces. Servo horns and idler horns are hardware supplied with the servos.-- The standard SO-101 gripper is replaced by the NC90 parallel gripper; do not count both.-- XT60 front extension, rejected cover extensions, parked complete-cover study, fit coupons and demonstration cable geometry are excluded.-- No dedicated battery cradle is in the final printed set.--## Naming and release status--The current physical prototype is **V0.3**. R8, R8H, R10, R11 and V2-01 inside filenames are historical component identifiers; retain them for traceability and do not treat them as the current robot version. The next hardware revision is V0.4; its in-progress changes are tracked separately in `hardware_v04.md`. This inventory remains the V0.3 reference. A successful print and an assembled, validated part are separate milestones.--## Source records--- `MOSS_lots_impression_20260917/MANIFESTE.json` and plate-02/03 contents.-- `MOSS_suite_fabrication_20260917/*/Contenu.md` for wheels, tensioners, spacers and gaskets.-- `MOSS_P1S_04_PETG_noir/LIRE.md` and `LIRE_06.md` for replacement P1S plates.-- `MOSS_PLA_suite_20260918/plaques.json` for interior supports, arm, gripper and pads.-- `MOSS_supports_moteurs_V2_01/LIRE_AVANT_MONTAGE.md` for the corrected bracket pair.-- Latest builder report on completion and track stiffness.--The accompanying [machine-readable inventory](printed_parts.json) carries the same quantities and status distinctions.diff --git a/docs/roadmap.md b/docs/roadmap.mddeleted file mode 100644index d41407d..0000000--- a/docs/roadmap.md+++ /dev/null@@ -1,11 +0,0 @@-# Roadmap--- **Now (V0.3 prototype)**: the print set is complete and the rover rolled for the first time on 22 September. Fix the track tension (second tensioner per track), measure ticks per revolution, write the Jetson–ESP32 interface then speed control; fit the arm. What turns out wrong is logged in [assembly_feedback.md](assembly_feedback.md); some fixes go on the prototype, the others into V0.4, which also gets mounts for the ESP32-S3, the servo adapter and the real power distribution. Manufacturing files are published part by part once their validation is decided.-- **Next**: first roadside run, teleoperated with a gamepad through dimOS; first recordings.-- **Then**: mount the arm and gripper; collect pick-up demonstrations; publish the first pooled dataset.-- **Later**: first policy; first autonomous pick on video; kits so the first hundred builders do not have to source parts themselves.--No dates. Each step is posted when it is real.-- **Lower-cost Pi build (experimental)**: Raspberry Pi 5 8 GB with either Mighty Camera or STEVAL-VL53L9 3D ToF, plus a colour camera. Start with teleop and data collection, then evaluate navigation and detection with dimOS on the Pi. Next: mount and test both sensors with dimOS, teleop and data collection first, then navigation and detection. Nothing is validated until it runs on the rover.--- **V0.4 hull and wiring**: current CAD includes the revised electronics arrangement, Jetson cable route, battery envelope and exterior-access motor fasteners. QT Py, screw-terminal BFF and INA219 STEMMA QT replace the DevKitC and the bare INA module. Reconcile the new INA footprint and real USB connectors, port the controller pin map and validate the printed assembly before release. [Detailed status](hardware_v04.md).diff --git a/docs/software.md b/docs/software.mddeleted file mode 100644index 4676e44..0000000--- a/docs/software.md+++ /dev/null@@ -1,34 +0,0 @@-# Software notes--MOSS runs on dimOS. The software here starts as a scaffold derived from vector-dimos, the external dimOS blueprint written for VECTOR (a mecanum rover on the same Jetson Orin Nano 8 GB).--What carries over: the idea of a gamepad module publishing a Twist behind a deadman, the rig/onboard split over zenoh, the recording tooling.--What is written for MOSS: `moss_dimos/teleop_logic.py` (pure: two stick axes only, forward and yaw, no lateral input exists; deadzone; deadman with a brake window of zeros; every value validated) and `moss_dimos/diffdrive.py` (differential-drive kinematics, scaling instead of clipping, invalid configs and non-finite commands refused). `moss_dimos/gamepad.py` is the thin dimOS wrapper around them. The motor layer on the microcontroller side exists: [`firmware/`](../firmware/README.md), an ESP32-S3 commissioning firmware (newline-terminated serial commands over USB-UART at 115200 baud: `arm`, `drive LEFT RIGHT`, `test left|right PERCENT`, `stop`, `status`, `zero`; disarmed at boot; a 300 ms command watchdog stops and disarms; 25 % commissioning limit; JSON telemetry every 200 ms with raw encoder ticks and battery voltage). Its command set is the Jetson–ESP32 contract for now. The Jetson-side driver that speaks it, speed control and odometry are not written yet.--Everything in `moss_dimos/` is cold-tested only until the base runs.--## Driving from a Raspberry Pi 5 (`moss_pi/`, no dimOS)--`moss_pi/` drives MOSS from a Raspberry Pi 5 through the same ESP32-S3 firmware and its serial commands, without dimOS. It reuses the pure pad logic in `moss_dimos/teleop_logic.py` (forward and yaw only, deadzone, brake window) and needs only the Python standard library plus pyserial, and pygame for a gamepad.--- `serial_bridge.py` writes `status`, `arm`, `stop`, `zero` and `drive LEFT RIGHT` (integers, -25..+25) and parses the JSON telemetry. It refuses to drive before `arm` and sends `stop` when 300 ms pass without a drive command. It also disarms on any `ERR` reply and reopens a lost port every second, sending `stop` first. `test` is left out: it is a bench command.-- `teleop.py`, keyboard or gamepad. Nothing moves until you press arm with the deadman released. Hold the deadman to drive. On release it sends `drive 0 0` for 0.5 s, then `stop`, which disarms, so each new drive needs a new arm. The stick is mapped open loop: `max_track_speed_mps` (0.6 by default) becomes 25 % PWM duty. The speed MOSS actually reaches at 25 % has not been measured.-- `telemetry_log.py` appends each telemetry line to a JSONL file as `{"wall_time_s": ..., "telemetry": {...}}`. On its own it only listens.--On the Pi, from a clone of this repository:--```-python3 -m venv .venv && . .venv/bin/activate-pip install -e '.[pi,test]'-python -m pytest tests # cold tests, no robot needed-sudo usermod -aG dialout "$USER" # once, then log in again-ls /dev/serial/by-id/ # find the ESP32 USB-UART adapter-python -m moss_pi.telemetry_log --port /dev/ttyUSB0 --out telemetry.jsonl-python -m moss_pi.teleop --port /dev/ttyUSB0 --keyboard # r arm, hold w/s/a/d, space stop, q quit-python -m moss_pi.teleop --port /dev/ttyUSB0 --gamepad --log drive.jsonl # A arm, hold L1, R1 boost-```--Use the DevKitC port wired to the USB-to-UART bridge (see [`firmware/`](../firmware/README.md)). It shows up as `/dev/ttyUSB0` or `/dev/ttyACM0`, depending on the bridge chip. A terminal reports key presses but not key releases, so with the keyboard a key counts as held for 0.6 s after its last repeat, and the rover brakes later than with a pad. Put the rover on blocks for the first run.--State: cold-tested only, against a fake serial port that replays the 20 September 2026 bench telemetry and against a Linux pseudo-terminal through pyserial. Nothing in `moss_pi/` has run on a Pi or on the rover yet.diff --git a/hardware/README.md b/hardware/README.mdindex 40d52f9..970cc1f 100644--- a/hardware/README.md+++ b/hardware/README.md@@ -1,7 +1,7 @@# Hardware-Design in Fusion 360. The current prototype is **V0.3**, being assembled from its first print set (113 pieces, see `docs/printed_parts.md`). Fit problems are logged in `docs/assembly_feedback.md`: some are fixed on the prototype, the others wait for V0.4. The current hull CAD and ordered electronics are described in [the V0.4 update](../docs/hardware_v04.md); this is not yet a tested replacement for the prototype.+Designed in Fusion 360. The STL (one file per part) and STEP files land here at the design freeze, with the fastener list and the sources they derive from (SO-101 arm, NormaCore NC90 gripper) with exact revisions and local changes. The freeze happens after one test on the real robot: a full battery emptied over 3 km on the beach, tracks still on, no bolt lost.-Manufacturing files (STL/STEP) are published here part by part once their validation is decided, with the fastener list (type, thread, length, head, quantity, what goes into PETG with inserts) and the sources they derive from (SO-101 arm, NormaCore gripper) with exact revisions and local changes. Until then, the photos in `media/`, the inventory and the BOM are the reference.+Until then: the [parts list](../3DPrinting.md), the [BOM](../BOM.md) and the photos in `media/` are the reference.-`bench/` holds the raw traces of the bench tests, one folder per date. Each trace is only what the build log says it is: the 20 September INA219 file is explicitly not a motor-current measurement.+`bench/` holds the raw traces of the bench tests, one folder per date. The 20 September INA219 trace is not a motor-current measurement.diff --git a/media/MOSS_cost_comparison_20260921_credits.md b/media/MOSS_cost_comparison_20260921_credits.mddeleted file mode 100644index 023cd3c..0000000--- a/media/MOSS_cost_comparison_20260921_credits.md+++ /dev/null@@ -1,12 +0,0 @@-# MOSS hardware cost comparison — 21 September 2026--Video: `video/MOSS_cost_comparison_20260921.mp4` (45 seconds, 1920 × 1080, 30 fps). Poster: `images/MOSS_cost_comparison_20260921.jpg`.--MOSS prototype footage and CAD animation: Show Robotics / Laurent Genoud. Music: newly synthesised instrumental, with no third-party samples or original camera audio. Typography: Space Grotesk. Budget figures and assumptions: [itemized BOM](../docs/bom-costs.md).--Product photography shown for identification and comparison:--- Mighty Camera: [manufacturer story](https://mightycamera.com/story), [source photograph](https://mightycamera.com/logs-media/2067991167195857008-1-2067805782247440384.jpg).-- STMicroelectronics STEVAL-VL53L9: [manufacturer product page](https://www.st.com/en/evaluation-tools/steval-vl53l9.html); photograph retrieved from [publicly shared product image](https://pbs.twimg.com/media/HLroGirXQAAHw0V.jpg).--Third-party product photographs and trademarks retain their respective owners' rights and are not offered under the repository's CC BY 4.0 licence. No separate permission or open licence for those photographs has been established. Original phone footage and standalone manufacturer image files are not part of this update.diff --git a/media/images/moss_exploded_turntable.gif b/media/images/moss_exploded_turntable.gifdeleted file mode 100644index 261f5f1..0000000Binary files a/media/images/moss_exploded_turntable.gif and /dev/null differdiff --git a/media/images/moss_pickup_loop.gif b/media/images/moss_pickup_loop.gifdeleted file mode 100644index 4d3caae..0000000Binary files a/media/images/moss_pickup_loop.gif and /dev/null differdiff --git a/media/images/moss_tracks_turn.gif b/media/images/moss_tracks_turn.gifdeleted file mode 100644index cd2298a..0000000Binary files a/media/images/moss_tracks_turn.gif and /dev/null differdiff --git a/media/images/moss_v04_hardware_tour.gif b/media/images/moss_v04_hardware_tour.gifdeleted file mode 100644index 2ab49aa..0000000Binary files a/media/images/moss_v04_hardware_tour.gif and /dev/null differdiff --git a/media/images/moss_v05_rover.jpg b/media/images/moss_v05_rover.jpgnew file mode 100644index 0000000..a4ee1d1Binary files /dev/null and b/media/images/moss_v05_rover.jpg differdiff --git a/media/images/moss_v06_modular.jpg b/media/images/moss_v06_modular.jpgnew file mode 100644index 0000000..9ea6d61Binary files /dev/null and b/media/images/moss_v06_modular.jpg differdiff --git a/media/images/moss_v06_parts.jpg b/media/images/moss_v06_parts.jpgnew file mode 100644index 0000000..6061865Binary files /dev/null and b/media/images/moss_v06_parts.jpg differdiff --git a/media/video/MOSS_V04_Inside_and_Action_20260924.mp4 b/media/video/MOSS_V04_Inside_and_Action_20260924.mp4deleted file mode 100644index 8748f9c..0000000Binary files a/media/video/MOSS_V04_Inside_and_Action_20260924.mp4 and /dev/null differdiff --git a/media/video/MOSS_V2_3_1_20260915.mp4 b/media/video/MOSS_V2_3_1_20260915.mp4deleted file mode 100644index 84cf6ed..0000000Binary files a/media/video/MOSS_V2_3_1_20260915.mp4 and /dev/null differdiff --git a/media/video/MOSS_build_log_02_20260918.mp4 b/media/video/MOSS_build_log_02_20260918.mp4deleted file mode 100644index b69a564..0000000Binary files a/media/video/MOSS_build_log_02_20260918.mp4 and /dev/null differdiff --git a/media/video/MOSS_build_update_20260917.mp4 b/media/video/MOSS_build_update_20260917.mp4deleted file mode 100644index cbca7ed..0000000Binary files a/media/video/MOSS_build_update_20260917.mp4 and /dev/null differdiff --git a/media/video/MOSS_cost_comparison_20260921.mp4 b/media/video/MOSS_cost_comparison_20260921.mp4deleted file mode 100644index 780ab83..0000000Binary files a/media/video/MOSS_cost_comparison_20260921.mp4 and /dev/null differdiff --git a/media/video/MOSS_exploded_turntable_20260918.mp4 b/media/video/MOSS_exploded_turntable_20260918.mp4deleted file mode 100644index b0a58e3..0000000Binary files a/media/video/MOSS_exploded_turntable_20260918.mp4 and /dev/null differdiff --git a/media/video/MOSS_first_assembly_20260920.mp4 b/media/video/MOSS_first_assembly_20260920.mp4deleted file mode 100644index 696d567..0000000Binary files a/media/video/MOSS_first_assembly_20260920.mp4 and /dev/null differdiff --git a/media/video/MOSS_first_drive_20260922.mp4 b/media/video/MOSS_first_drive_20260922.mp4deleted file mode 100644index 82e53b3..0000000Binary files a/media/video/MOSS_first_drive_20260922.mp4 and /dev/null differdiff --git a/media/video/MOSS_motor_encoder_bench_20260920.mp4 b/media/video/MOSS_motor_encoder_bench_20260920.mp4deleted file mode 100644index ec87296..0000000Binary files a/media/video/MOSS_motor_encoder_bench_20260920.mp4 and /dev/null differdiff --git a/media/video/MOSS_print_set_bench_20260919.mp4 b/media/video/MOSS_print_set_bench_20260919.mp4deleted file mode 100644index 4b19c69..0000000Binary files a/media/video/MOSS_print_set_bench_20260919.mp4 and /dev/null differ