Skip to content

armgit / moss

Public Imported from GitHub
0

MOSS: a small, mostly 3D-printed litter-picking rover. Cleaner streets, one maker at a time.

Python

Pages for the reader: prices without commentary, no process words; one line of state per page

metroxcb4ccb7fa3b8
diff --git a/3DPrinting.md b/3DPrinting.md
index e048589..954e20e 100644
--- a/3DPrinting.md
+++ b/3DPrinting.md
@@ -1,6 +1,6 @@
# 3D printing
-**107 printed parts** on the assembled rover: 82 in PETG, 19 in PLA, 6 in TPU 95A. Counted on the V0.5 CAD on 1 October 2026. The STL files, one per part, land in [`hardware/`](hardware/) at the design freeze; this page is the list to plan against.
+**107 printed parts**: 82 in PETG, 19 in PLA, 6 in TPU 95A. The STL files, one per part, come with the release in [`hardware/`](hardware/).
| Material | Where |
|---|---|
@@ -65,4 +65,4 @@ The SO-101 parts are the upstream files with cable clips added. The gripper is N
## Filament
-Sliced so far, supports included: 1.15 kg of PETG and 1.1 kg of PLA for the hull, cover (465 g), bin (549 g), arm plate and brackets. The drivetrain, arm and tracks add to it. Plan on 2 kg of PETG, 2 kg of PLA and a roll of TPU.
+Plan on 2 kg of PETG, 2 kg of PLA and a roll of TPU.
diff --git a/Assembly.md b/Assembly.md
index 36eebbc..dc60813 100644
--- a/Assembly.md
+++ b/Assembly.md
@@ -1,6 +1,6 @@
# Assembly
-**Photos from the first prototype, V0.3, September 2026.** The step-by-step with the V0.6 parts is shot during the rebuild and replaces this page when the files come out. Read [docs/lessons.md](docs/lessons.md) before you start: it is short, and it is everything that bit us.
+Photos from the first prototype. The step-by-step with the final parts comes with the files. Read [docs/lessons.md](docs/lessons.md) first; it is short.
## 1. Lay out the print set
diff --git a/BOM.md b/BOM.md
index 6b02613..04d8ceb 100644
--- a/BOM.md
+++ b/BOM.md
@@ -1,6 +1,6 @@
# Bill of materials
-**Estimates, retail, one rover.** Checked against the V0.5 CAD on 1 October 2026. Prices in USD; a line marked *paid* is what we actually paid, the others are listings or allowances. A kit will cost less: filament by the gram instead of the spool, servos and bearings in volume.
+Retail prices in USD, one rover. A kit will cost less.
## Totals
@@ -14,21 +14,21 @@
| 2D lidar | | 72 | 72 | 72 |
| **Total** | **about $480** | **about $1,540** | **about $1,260** | **about $890** |
-The Jetson configuration is the prototype. The two Pi configurations are drawn, not yet run.
-
## Computer and perception
-| Item | Qty | USD | Note |
-|---|---:|---:|---|
-| NVIDIA Jetson Orin Nano Super 8 GB | 1 | 480 | boots from a microSD card, 15 |
-| Intel RealSense D455 | 1 | 466 | *paid*. Depth from 0.12 m with the current close-range software |
-| USB 3.1 C to A cable, 90° plug with locking screws, 0.3 m | 1 | 7 | *paid*. The straight plug does not fit in the hull |
-| Raspberry Pi 5 8 GB | 1 | 175 | with active cooler 8, 5 V supply 20, microSD 15 |
-| Raspberry Pi AI HAT+ 2 (Hailo-10H, 40 TOPS) | 1 | 232 | *paid*; list price about 200 |
-| Orbbec Gemini 2 | 1 | 234 | listing. Depth from 0.15 m, 91° × 66° |
-| Mighty Camera, visual-inertial tracking, onboard IMU | 1 | 92 | *paid*. Pose estimation on the camera itself, no accelerator needed |
-| Wrist camera, innomaker 1080p USB module, 32 × 32 mm | 1 | 19 | listing |
-| SLAMTEC RPLIDAR C1 | 1 | 72 | listing (RobotShop, DFRobot). Mount printed; position on the cover still being settled |
+| Item | Qty | USD |
+|---|---:|---:|
+| NVIDIA Jetson Orin Nano Super 8 GB | 1 | 480 |
+| microSD card (Jetson) | 1 | 15 |
+| Raspberry Pi 5 8 GB | 1 | 175 |
+| Pi active cooler, 5 V supply, microSD | 1 | 43 |
+| Raspberry Pi AI HAT+ 2 (Hailo-10H, 40 TOPS) | 1 | 232 |
+| Intel RealSense D455 | 1 | 466 |
+| USB 3.1 C to A cable, 90° plug with locking screws, 0.3 m | 1 | 7 |
+| Orbbec Gemini 2 | 1 | 234 |
+| Mighty Camera | 1 | 92 |
+| Wrist camera, innomaker 1080p USB module, 32 × 32 mm | 1 | 19 |
+| SLAMTEC RPLIDAR C1 | 1 | 72 |
## Kit base, about $482
@@ -44,70 +44,68 @@ The Jetson configuration is the prototype. The two Pi configurations are drawn,
### Control electronics
-| Item | Qty | Unit | Line | Note |
-|---|---:|---:|---:|---|
-| Adafruit QT Py ESP32-S3, 8 MB flash, no PSRAM (5426) | 1 | 12.50 | 12.50 | *paid* |
-| Adafruit Terminal Block BFF (6495) | 1 | 10.95 | 10.95 | *paid*. Screw terminals instead of jumper wires |
-| Adafruit INA219 STEMMA QT (904) | 1 | 9.95 | 9.95 | *paid*. Battery voltage only |
-| STEMMA QT cable, 300 mm (5384) | 1 | 1.25 | 1.25 | *paid* |
-| Cytron MDD3A dual motor driver, 4–16 V, 3 A per channel | 1 | 9.53 | 9.53 | listing |
-| Waveshare Bus Servo Adapter (A) | 1 | 5 | 5 | estimate |
+| Item | Qty | Unit | Line |
+|---|---:|---:|---:|
+| Adafruit QT Py ESP32-S3, 8 MB flash, no PSRAM (5426) | 1 | 12.50 | 12.50 |
+| Adafruit Terminal Block BFF (6495) | 1 | 10.95 | 10.95 |
+| Adafruit INA219 STEMMA QT (904) | 1 | 9.95 | 9.95 |
+| STEMMA QT cable, 300 mm (5384) | 1 | 1.25 | 1.25 |
+| Cytron MDD3A dual motor driver, 4–16 V, 3 A per channel | 1 | 9.53 | 9.53 |
+| Waveshare Bus Servo Adapter (A) | 1 | 5 | 5 |
### Drive
-| Item | Qty | Unit | Line | Note |
-|---|---:|---:|---:|---|
-| 12 V geared DC motor with quadrature encoder | 2 | 15 | 30 | estimate; exact reference to pin with the files |
+| Item | Qty | Unit | Line |
+|---|---:|---:|---:|
+| 12 V geared DC motor with quadrature encoder | 2 | 15 | 30 |
### Arm and gripper
-| Item | Qty | Unit | Line | Note |
-|---|---:|---:|---:|---|
-| ST3215 12 V bus servo | 5 | 22 | 110 | arm joints |
-| CF35-12 constant-force servo | 1 | 50 | 50 | gripper |
-
-The camera in the hand is counted with the sensors above.
+| Item | Qty | Unit | Line |
+|---|---:|---:|---:|
+| ST3215 12 V bus servo | 5 | 22 | 110 |
+| CF35-12 constant-force servo (gripper) | 1 | 50 | 50 |
### Power and wiring
-| Item | Qty | Unit | Line | Note |
-|---|---:|---:|---:|---|
-| 3S lithium pack with BMS | 1 | 35 | 35 | allowance; pack not specified yet |
-| 12.6 V CC/CV charger | 1 | 12 | 12 | estimate |
-| Emergency stop (16 mm, LA16-11ZS/A), fuse holder, fuses, distribution | lot | 18 | 18 | e-stop *paid* 2.23 |
-| Wiring, ferrules, heat-shrink, 2 × DC 5.5 × 2.1 mm panel sockets | lot | 15 | 15 | sockets *paid* 1.51 each |
-| XT30 pairs: one input, four outputs (arm, computer, driver, fans) | 5 | | | not priced yet; printed housing |
-| USB cables for the controller and the servo adapter | lot | 10 | 10 | estimate |
-
-### Mechanical hardware
+| Item | Qty | Unit | Line |
+|---|---:|---:|---:|
+| 3S lithium pack with BMS | 1 | 35 | 35 |
+| 12.6 V CC/CV charger | 1 | 12 | 12 |
+| Emergency stop (16 mm), fuse holder, fuses, distribution | lot | 18 | 18 |
+| Wiring, ferrules, heat-shrink, 2 × DC 5.5 × 2.1 mm panel sockets | lot | 15 | 15 |
+| XT30 pairs: one input, four outputs (arm, computer, driver, fans) | 5 | | |
+| USB cables for the controller and the servo adapter | lot | 10 | 10 |
-| Item | Qty | Note |
-|---|---:|---|
-| Bearings 625 | 12 | two per roller |
-| Bearings 608 | 4 | two per idler wheel |
-| Bearings 626 | 4 | motor side and outer |
-| Shaft collars Ø5, Ø6, Ø8 bore | 12, 2, 4 | Ø8 *paid* 2.14 each |
-| Shafts: Ø5 × 80 (6), Ø6 × 90 (2), Ø8 × 100 (2) mm | 10 | cut from Ø5 × 500, Ø6 × 250, Ø8 × 250 mm bars |
-| Rigid motor-to-shaft couplings, Ø6 bores | 2 | |
-| HEX12 metal wheel hubs, Ø6 bore, 18 mm | 2 | drop if supplied with the motors |
+### Mechanical hardware, about $61
-Bearings about 12, collars 18, bars 8, couplings 5, hubs 3, screws 15: about $61.
-
-Screws in the drivetrain: M3 × 16 (22), M3 × 20 (6), M3 × 25 (6), M3 × 35 (18), M4 × 16 (6), M4 × 40 (4), M4 × 60 (4), M2.5 × 10 (4); 52 M3 nuts, 18 M4 nuts (4 lock nuts), 8 M4 washers. The hull hatch and the arm add M3 positions whose lengths are fixed with the files.
+| Item | Qty |
+|---|---:|
+| Bearings 625 | 12 |
+| Bearings 608 | 4 |
+| Bearings 626 | 4 |
+| Shaft collars, Ø5 bore | 12 |
+| Shaft collars, Ø6 bore | 2 |
+| Shaft collars, Ø8 bore | 4 |
+| Shafts Ø5 × 80 mm | 6 |
+| Shafts Ø6 × 90 mm | 2 |
+| Shafts Ø8 × 100 mm | 2 |
+| Rigid motor-to-shaft couplings, Ø6 bores | 2 |
+| HEX12 metal wheel hubs, Ø6 bore, 18 mm | 2 |
+
+Screws: M3 × 16 (22), M3 × 20 (6), M3 × 25 (6), M3 × 35 (18), M4 × 16 (6), M4 × 40 (4), M4 × 60 (4), M2.5 × 10 (4); 52 M3 nuts, 18 M4 nuts (4 lock nuts), 8 M4 washers.
### Filament
-| Filament | Qty | Unit | Line | Note |
-|---|---:|---:|---:|---|
-| PETG, black | 2 kg | 10.39 | 20.79 | *paid* |
-| PLA, matte | 2 kg | 20.64 | 41.27 | *paid* |
-| TPU 95A | 1 kg | 25 | 25 | tracks and pads |
-
-The sliced hull, cover, bin and brackets alone use 1.15 kg of PETG and 1.1 kg of PLA. See [3D printing](3DPrinting.md).
+| Filament | Qty | Unit | Line |
+|---|---:|---:|---:|
+| PETG, black | 2 kg | 10.39 | 20.79 |
+| PLA, matte | 2 kg | 20.64 | 41.27 |
+| TPU 95A | 1 kg | 25 | 25 |
### Fans and magnets
-| Item | Qty | Unit | Line | Note |
-|---|---:|---:|---:|---|
-| 3010 fan, 12 V | 2 | 1.68 | 3.35 | *paid*. Rear extraction |
-| Magnet 20 × 10 × 2 mm | 4 | 0.43 | 1.73 | *paid*. Two in the cover, two in the bin |
+| Item | Qty | Unit | Line |
+|---|---:|---:|---:|
+| 3010 fan, 12 V | 2 | 1.68 | 3.35 |
+| Magnet 20 × 10 × 2 mm | 4 | 0.43 | 1.73 |
diff --git a/CHANGELOG.md b/CHANGELOG.md
index 304ad18..7b0bfd2 100644
--- a/CHANGELOG.md
+++ b/CHANGELOG.md
@@ -2,7 +2,7 @@
Hardware revisions. Dates are when it was real, not when it was planned.
-- **V0.6** (October 2026, prototype being assembled): modular compute and perception plates (Jetson or Raspberry Pi; RealSense or Orbbec Gemini), XT30 power block, 12 V to 5 V converter for the Pi, hull R7, tracks 70 teeth at 10 mm pitch.
-- **V0.5** (1 October 2026): redrawn on the real V0.3 robot; one-piece hull, two tensioners per track, mounts for every board, magnets for the bin. Release candidate for the open source CAD. 107 printed parts.
-- **V0.4** (24 September 2026, drawn, parts printed): revised hull, screw-terminal controller, one dual motor driver.
+- **V0.6** (October 2026): modular compute and perception plates (Jetson or Raspberry Pi; RealSense or Orbbec Gemini), XT30 power block, 12 V to 5 V converter for the Pi, hull R7, tracks 70 teeth at 10 mm pitch.
+- **V0.5** (1 October 2026): redrawn on the real robot; one-piece hull, two tensioners per track, mounts for every board, magnets for the bin. 107 printed parts.
+- **V0.4** (24 September 2026): revised hull, screw-terminal controller, one dual motor driver.
- **V0.3** (22 September 2026): first prototype. First drive on 22 September, arm and gripper on 26 September.
diff --git a/README.md b/README.md
index f492669..badb17e 100644
--- a/README.md
+++ b/README.md
@@ -24,7 +24,7 @@ Retail estimates for one rover, parts only. A kit will be cheaper.
| + Raspberry Pi 5, Hailo AI HAT, Orbbec Gemini 2, wrist camera, 2D lidar | about $1,260 |
| + Raspberry Pi 5, Mighty camera, wrist camera, 2D lidar | about $890 |
-The Jetson configuration is the one on the bench. The Pi configurations are drawn, not yet run. Every line is in the [BOM](BOM.md).
+The Jetson configuration is the one on the bench. Every line is in the [BOM](BOM.md).
![Your hardware, your MOSS: Pi or Jetson, RealSense or Gemini](media/images/moss_v06_modular.jpg)
@@ -63,4 +63,4 @@ This is a prototype with a lithium battery and no certified protection. Put it o
## License
-Code under Apache-2.0. Hardware files and documentation under CC BY 4.0 until the first file release, which will carry the hardware license named in `NOTICE`.
+Code under Apache-2.0. Hardware files and documentation under CC BY 4.0. See `NOTICE`.
diff --git a/Software.md b/Software.md
index d147ac4..9ec522f 100644
--- a/Software.md
+++ b/Software.md
@@ -2,7 +2,7 @@
Three layers. The microcontroller drives the motors. The computer on top sends it speeds and reads its telemetry. The policies come later, from pooled data.
-**State: the motor firmware ran on the bench and on the first drives. Everything on the computer side is tested against a fake serial port only; nothing has driven the rover from a Jetson or a Pi yet.**
+**The motor firmware drove the prototype. The computer side is tested against a fake serial port only.**
## Motor firmware, ESP32-S3