The ultimate harness for coding agents and beyond. All your agents. All your machines. One command center. Start with code, then follow your curiosity and build across disciplines: CAD, circuits, robots, games and music.
TypeScript 3d-modelingagent-frameworkagent-harnessai-agentscadclaude-codecodexcoding-agentsdeveloper-toolsesp32game-developmentmcp-servermulti-agentopen-hardwareopencodeopenharnesspcbroboticsterminaltmux
Add full product BOM and assembly/PCB photos
Hardware00142ad7ec41442
diff --git a/devices/harness-device/hardware/BOM.csv b/devices/harness-device/hardware/BOM.csvnew file mode 100644index 000000000..df425864a--- /dev/null+++ b/devices/harness-device/hardware/BOM.csv@@ -0,0 +1,12 @@+#,Component,Qty,Link+1,Speaker 2415 8Ω 1W (2-pin SH1.0 connector),1,https://www.aliexpress.us/item/3256813022741238.html+2,MX1.25 4-pin connector cable,1,https://www.aliexpress.us/item/3256812670096395.html+3,1.75" 466x466 round AMOLED display (DXQ0175Y003AMT003),1,https://www.alibaba.com/product-detail/DXQ-1-75-Inch-466-466_1601834013691.html+4,USB Type-C female PCB,1,https://www.aliexpress.us/item/3256809703885548.html+5,PCBA - Harness_1.75_AMOLED (main board, assembled),1,https://jlcpcb.com/+6,Self-adhesive rubber foot pad (round),1,https://www.aliexpress.us/item/3256806493767498.html+7,M2x5 screw,4,https://www.aliexpress.us/item/3256808488953951.html+8,Housing (3D printed),1,see hardware/3d/step/Housing.step+9,Button (3D printed),1,see hardware/3d/step/Button.step+10,USB clamp (3D printed),1,see hardware/3d/step/USB_clamp.step+11,Iron base (laser-cut from 3mm steel),1,see hardware/3d/step/Iron_base.stepdiff --git a/devices/harness-device/hardware/README.md b/devices/harness-device/hardware/README.mdindex 59ba8ee08..f9800edd7 100644--- a/devices/harness-device/hardware/README.md+++ b/devices/harness-device/hardware/README.md@@ -1,6 +1,43 @@# Harness device hardware-Mechanical and electrical design files for the harness-device.+Mechanical and electrical design files for the harness-device: a round USB companion with a+466×466 AMOLED touchscreen, dual microphones, and a speaker, built around a Waveshare+ESP32-S3-Touch-AMOLED-1.75C-compatible display module.++## Photos++| | |+|---|---|+|  **Assembled device — front**<br>The round AMOLED display sits flush in the housing; the side button is visible on the right edge. |  **Assembled device — rear (cutaway)**<br>Looking into the base: the USB-C clamp holds the port PCB in place, exposing the USB power/data pads (`V`, `-D`, `+D`, `G`). |+|  **Housing — empty shell**<br>The 3D-printed housing on its own, before the board is installed: mounting bosses, screw holes, and the USB-C cutout. |  **Housing — with PCB installed**<br>The main board seated in the housing: USB-C connector, display FPC connector, ESP32-S3 module, and supporting components. |+|  **PCB — front (top layer)**<br>Rev 2.0 board render: display FPC connector, dual microphones (green outlines), USB-C connector, and the ESP32-S3 and audio codec ICs. |  **PCB — back (bottom layer)**<br>ESP32-S3-WROOM module (with printed antenna trace), speaker connector (`SPK`), USB connector (`USB`), and the expansion FPC connector (`EXP`). |++## Bill of Materials++[`BOM.csv`](BOM.csv) lists every part needed to build one complete device — bought components and+3D/laser-cut parts alike — each with a sourcing link or a pointer to the design file that makes it.+This is the **full product BOM**; for just the PCB's own SMD components, see+`pcb/production/BOM_Harness_1.75_AMOLED_PCB_Harness_1.75.xlsx` below.++| # | Component | Qty | Source |+|---|---|---|---|+| 1 | Speaker, 2415 8Ω 1W (2-pin SH1.0 connector) | 1 | [AliExpress](https://www.aliexpress.us/item/3256813022741238.html) |+| 2 | MX1.25 4-pin connector cable | 1 | [AliExpress](https://www.aliexpress.us/item/3256812670096395.html) |+| 3 | 1.75″ 466×466 round AMOLED display (DXQ0175Y003AMT003) | 1 | [Alibaba](https://www.alibaba.com/product-detail/DXQ-1-75-Inch-466-466_1601834013691.html) |+| 4 | USB Type-C female PCB connector | 1 | [AliExpress](https://www.aliexpress.us/item/3256809703885548.html) |+| 5 | PCBA — Harness_1.75_AMOLED (main board, assembled) | 1 | [JLCPCB](https://jlcpcb.com/) — build from `pcb/` |+| 6 | Self-adhesive rubber foot pad (round) | 1 | [AliExpress](https://www.aliexpress.us/item/3256806493767498.html) |+| 7 | M2×5 screw | 4 | [AliExpress](https://www.aliexpress.us/item/3256808488953951.html) |+| 8 | Housing — 3D printed | 1 | `3d/step/Housing.step` |+| 9 | Button — 3D printed | 1 | `3d/step/Button.step` |+| 10 | USB clamp — 3D printed | 1 | `3d/step/USB_clamp.step` |+| 11 | Iron base — laser-cut, 3 mm steel | 1 | `3d/step/Iron_base.step` |++> The display module's silkscreen/BOM calls out a CST9217 touch controller, but the units actually+> sourced under this listing carry a CST816S instead (same footprint/form factor, different+> touch IC). The firmware auto-detects both — see the variant table in+> [`../firmware/README.md`](../firmware/README.md#supported-hardware) if you're bringing up a new+> board and the touchscreen doesn't respond.## PCB (`pcb/`)@@ -11,7 +48,7 @@ Designed in EasyEDA Pro.| `ProPrj_Harness_1.75_AMOLED.epro2` | EasyEDA Pro project (schematic + PCB layout source) || `SCH_SCH_Harness_1.75.pdf` | Schematic export (PDF) || `production/Gerber_PCB_Harness/` | Gerbers + drill files for fabrication (RS-274X / Excellon) |-| `production/BOM_Harness_1.75_AMOLED_PCB_Harness_1.75.xlsx` | Bill of materials |+| `production/BOM_Harness_1.75_AMOLED_PCB_Harness_1.75.xlsx` | PCB assembly BOM (SMD components only) || `production/PickAndPlace_PCB_Harness.xlsx` | Pick-and-place (CPL) data for assembly |Open the `.epro2` project in [EasyEDA Pro](https://pro.easyeda.com/) to edit the schematic/layout.@@ -28,6 +65,6 @@ Each part is provided in two formats, one per subfolder:|---|---|---|| Full assembled harness | `step/Harness_assembly.step` | `stl/Harness_assembly.stl` || Main enclosure housing | `step/Housing.step` | `stl/Housing.stl` |-| Iron counterweight block (keeps the device from tipping/sliding on a desk) | `step/Iron_base.step` | `stl/Iron_base.stl` |+| Iron counterweight block (keeps the device from tipping/sliding on a desk) — laser-cut from 3 mm iron sheet | `step/Iron_base.step` | `stl/Iron_base.stl` || Clamp that holds the USB-C port PCB in place | `step/USB_clamp.step` | `stl/USB_clamp.stl` || Physical button cap/actuator | `step/Button.step` | `stl/Button.stl` |diff --git a/devices/harness-device/hardware/images/Harness-assembled-1.png b/devices/harness-device/hardware/images/Harness-assembled-1.pngnew file mode 100644index 000000000..45912e72bBinary files /dev/null and b/devices/harness-device/hardware/images/Harness-assembled-1.png differdiff --git a/devices/harness-device/hardware/images/Harness-assembled-2.png b/devices/harness-device/hardware/images/Harness-assembled-2.pngnew file mode 100644index 000000000..e750d0b5aBinary files /dev/null and b/devices/harness-device/hardware/images/Harness-assembled-2.png differdiff --git a/devices/harness-device/hardware/images/Housing-3D-print.png b/devices/harness-device/hardware/images/Housing-3D-print.pngnew file mode 100644index 000000000..101add07cBinary files /dev/null and b/devices/harness-device/hardware/images/Housing-3D-print.png differdiff --git a/devices/harness-device/hardware/images/Housing-with-PCB.png b/devices/harness-device/hardware/images/Housing-with-PCB.pngnew file mode 100644index 000000000..9c441afb9Binary files /dev/null and b/devices/harness-device/hardware/images/Housing-with-PCB.png differdiff --git a/devices/harness-device/hardware/images/PCB-1.png b/devices/harness-device/hardware/images/PCB-1.pngnew file mode 100644index 000000000..ff89e34dfBinary files /dev/null and b/devices/harness-device/hardware/images/PCB-1.png differdiff --git a/devices/harness-device/hardware/images/PCB-2.png b/devices/harness-device/hardware/images/PCB-2.pngnew file mode 100644index 000000000..ca54eb69aBinary files /dev/null and b/devices/harness-device/hardware/images/PCB-2.png differ