SolidCraft: an open-source parametric 3D CAD application built in pure Rust. Desktop, web, and automation through MCP.
Wave 234/509: kernel-cases: #4432–#4829 triaged: 21 cases, 175 skipped
jyviko4c922a19a998
diff --git a/tests/kernel-cases/booleans/4468-box-minus-bore-measures-exact/expected.json b/tests/kernel-cases/booleans/4468-box-minus-bore-measures-exact/expected.jsonnew file mode 100644index 0000000000..e6aa2d035f--- /dev/null+++ b/tests/kernel-cases/booleans/4468-box-minus-bore-measures-exact/expected.json@@ -0,0 +1,14 @@+{+ "sources": [+ "tangency-labs/solidcraft#4468"+ ],+ "what": "a 20x15x5 box minus an r3 through bore: truck's measure read 1.66e-4 of the removed volume too much (1358.6518 for 1358.6283) while the geometry was exact",+ "source": "analytic",+ "method": "V = 20*15*5 - pi*3^2*5 = 1358.628331; A = 2*(300 - 9 pi) + 2*(20+15)*5 + 2*pi*3*5 = 993.226. Graded to 1e-6 relative, below the reported error (1.7e-5 of the result)",+ "body_count": 1,+ "volume_mm3": 1358.628331,+ "area_mm2": 987.699112,+ "tolerance": {+ "rel": 1e-06+ }+}diff --git a/tests/kernel-cases/booleans/4468-box-minus-bore-measures-exact/recipe.json b/tests/kernel-cases/booleans/4468-box-minus-bore-measures-exact/recipe.jsonnew file mode 100644index 0000000000..e7c12513ce--- /dev/null+++ b/tests/kernel-cases/booleans/4468-box-minus-bore-measures-exact/recipe.json@@ -0,0 +1,41 @@+{+ "commands": [+ {+ "command": "solid.box",+ "params": {+ "corner": [+ 0,+ 0,+ 0+ ],+ "length": 20,+ "width": 15,+ "height": 5,+ "body_name": "Box"+ }+ },+ {+ "command": "solid.cylinder",+ "params": {+ "radius": 3,+ "height": 7,+ "base": [+ 10,+ 7.5,+ -1+ ],+ "body_name": "Bore"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "Box",+ "tools": [+ "Bore"+ ],+ "operation": "cut"+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4505-join-coil-through-cylinder-wall/expected.json b/tests/kernel-cases/booleans/4505-join-coil-through-cylinder-wall/expected.jsonnew file mode 100644index 0000000000..2e302fc938--- /dev/null+++ b/tests/kernel-cases/booleans/4505-join-coil-through-cylinder-wall/expected.json@@ -0,0 +1,10 @@+{+ "sources": [+ "tangency-labs/solidcraft#4505",+ "tangency-labs/solidcraft#3636"+ ],+ "what": "a coil (diameter 151, pitch 10, 80 high, 5 mm round section) whose section runs through a diameter-152 cylinder's wall, joined to it: truck ground for 125-296 s, then 'boolean Union: no result'",+ "source": "invariants",+ "method": "the coil's section crosses the wall along its whole length, so the union is one connected solid: one valid closed body. The helical sweep's part outside r 76 has no closed-form volume (the triage's script)",+ "body_count": 1+}diff --git a/tests/kernel-cases/booleans/4505-join-coil-through-cylinder-wall/recipe.json b/tests/kernel-cases/booleans/4505-join-coil-through-cylinder-wall/recipe.jsonnew file mode 100644index 0000000000..241c7ae927--- /dev/null+++ b/tests/kernel-cases/booleans/4505-join-coil-through-cylinder-wall/recipe.json@@ -0,0 +1,38 @@+{+ "commands": [+ {+ "command": "solid.cylinder",+ "params": {+ "diameter": 152,+ "height": 100,+ "body_name": "Cyl"+ }+ },+ {+ "command": "solid.coil",+ "params": {+ "diameter": 151,+ "pitch": 10,+ "height": 80,+ "section_size": 5,+ "base": [+ 0,+ 0,+ 10+ ],+ "operation": "new",+ "body_name": "Coil"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "Cyl",+ "tools": [+ "Coil"+ ],+ "operation": "join"+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4558-join-tool-grown-past-block/expected.json b/tests/kernel-cases/booleans/4558-join-tool-grown-past-block/expected.jsonnew file mode 100644index 0000000000..ad1f0718fa--- /dev/null+++ b/tests/kernel-cases/booleans/4558-join-tool-grown-past-block/expected.json@@ -0,0 +1,12 @@+{+ "sources": [+ "tangency-labs/solidcraft#4558"+ ],+ "what": "a 10 mm join on a block's top face whose sketch is then edited out past the block on every side (60 x 50 on a 40 x 30 top): truck refused the rebuilt join ('join cannot preserve the original faces') and dropped it",+ "source": "analytic",+ "method": "block 40x30x20 = 24000 plus the slab 60x50x10 = 30000 standing on it: V = 54000. Faces: block bottom and 4 sides, the slab's under face (60x50 less 40x30), its 4 sides and top = 11. Area 1200 + 2800 + 1800 + 2200 + 3000 = 11000. The sketch is made without projected face edges, so its rectangle is one region",+ "body_count": 1,+ "volume_mm3": 54000.0,+ "area_mm2": 11000.0,+ "faces": 11+}diff --git a/tests/kernel-cases/booleans/4558-join-tool-grown-past-block/recipe.json b/tests/kernel-cases/booleans/4558-join-tool-grown-past-block/recipe.jsonnew file mode 100644index 0000000000..dc12949884--- /dev/null+++ b/tests/kernel-cases/booleans/4558-join-tool-grown-past-block/recipe.json@@ -0,0 +1,110 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY"+ }+ },+ {+ "command": "sketch.rectangle.two_point",+ "params": {+ "p0": [+ -20,+ -15+ ],+ "p1": [+ 20,+ 15+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "distance": 20+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "face": [+ 0,+ 0,+ 20+ ]+ },+ "project_edges": false+ }+ },+ {+ "command": "sketch.rectangle.two_point",+ "params": {+ "p0": [+ -10,+ -5+ ],+ "p1": [+ 10,+ 5+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "distance": 10,+ "operation": "join",+ "profiles": [+ {+ "curves": [+ "l1",+ "l2",+ "l3",+ "l4"+ ]+ }+ ]+ }+ },+ {+ "command": "sketch.edit",+ "params": {+ "sketch": "Sketch2"+ }+ },+ {+ "command": "sketch.move_point",+ "params": {+ "point": "p3",+ "to": [+ 30,+ 25+ ]+ }+ },+ {+ "command": "sketch.move_point",+ "params": {+ "point": "p1",+ "to": [+ -30,+ -25+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4623-join-crossing-pleated-loft-skins/expected.json b/tests/kernel-cases/booleans/4623-join-crossing-pleated-loft-skins/expected.jsonnew file mode 100644index 0000000000..f44f64de6a--- /dev/null+++ b/tests/kernel-cases/booleans/4623-join-crossing-pleated-loft-skins/expected.json@@ -0,0 +1,11 @@+{+ "sources": [+ "tangency-labs/solidcraft#4623",+ "tangency-labs/solidcraft#4180",+ "tangency-labs/solidcraft#4881"+ ],+ "what": "a join of two pleated skins (lofts between 24-pleat star outlines, less the same loft moved in 1.1 mm) that cross along a ring near their bottoms: truck panicked ('tolerance must be no less than 1e-6') or gave no result",+ "source": "invariants",+ "method": "the narrowing cone skin and the flaring lip skin cross at z = -0.3, so their union is one connected solid: one valid closed body, no panic. The reporter's own script (pleated_union.py, 24 pleats)",+ "body_count": 1+}diff --git a/tests/kernel-cases/booleans/4623-join-crossing-pleated-loft-skins/recipe.json b/tests/kernel-cases/booleans/4623-join-crossing-pleated-loft-skins/recipe.jsonnew file mode 100644index 0000000000..080ca8c3be--- /dev/null+++ b/tests/kernel-cases/booleans/4623-join-crossing-pleated-loft-skins/recipe.json@@ -0,0 +1,1802 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "-1",+ "name": "ConeLo"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 115.7949,+ 0.0+ ],+ [+ 112.5082,+ 14.812+ ],+ [+ 111.8493,+ 29.9699+ ],+ [+ 104.8409,+ 43.4265+ ],+ [+ 100.2813,+ 57.8974+ ],+ [+ 90.0289,+ 69.0816+ ],+ [+ 81.8793,+ 81.8793+ ],+ [+ 69.0816,+ 90.0289+ ],+ [+ 57.8974,+ 100.2813+ ],+ [+ 43.4265,+ 104.8409+ ],+ [+ 29.9699,+ 111.8493+ ],+ [+ 14.812,+ 112.5082+ ],+ [+ 0.0,+ 115.7949+ ],+ [+ -14.812,+ 112.5082+ ],+ [+ -29.9699,+ 111.8493+ ],+ [+ -43.4265,+ 104.8409+ ],+ [+ -57.8974,+ 100.2813+ ],+ [+ -69.0816,+ 90.0289+ ],+ [+ -81.8793,+ 81.8793+ ],+ [+ -90.0289,+ 69.0816+ ],+ [+ -100.2813,+ 57.8974+ ],+ [+ -104.8409,+ 43.4265+ ],+ [+ -111.8493,+ 29.9699+ ],+ [+ -112.5082,+ 14.812+ ],+ [+ -115.7949,+ 0.0+ ],+ [+ -112.5082,+ -14.812+ ],+ [+ -111.8493,+ -29.9699+ ],+ [+ -104.8409,+ -43.4265+ ],+ [+ -100.2813,+ -57.8974+ ],+ [+ -90.0289,+ -69.0816+ ],+ [+ -81.8793,+ -81.8793+ ],+ [+ -69.0816,+ -90.0289+ ],+ [+ -57.8974,+ -100.2813+ ],+ [+ -43.4265,+ -104.8409+ ],+ [+ -29.9699,+ -111.8493+ ],+ [+ -14.812,+ -112.5082+ ],+ [+ -0.0,+ -115.7949+ ],+ [+ 14.812,+ -112.5082+ ],+ [+ 29.9699,+ -111.8493+ ],+ [+ 43.4265,+ -104.8409+ ],+ [+ 57.8974,+ -100.2813+ ],+ [+ 69.0816,+ -90.0289+ ],+ [+ 81.8793,+ -81.8793+ ],+ [+ 90.0289,+ -69.0816+ ],+ [+ 100.2813,+ -57.8974+ ],+ [+ 104.8409,+ -43.4265+ ],+ [+ 111.8493,+ -29.9699+ ],+ [+ 112.5082,+ -14.812+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "88.3",+ "name": "ConeHi"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 14.39,+ 0.0+ ],+ [+ 13.9816,+ 1.8407+ ],+ [+ 13.8997,+ 3.7244+ ],+ [+ 13.0287,+ 5.3967+ ],+ [+ 12.4621,+ 7.195+ ],+ [+ 11.188,+ 8.5849+ ],+ [+ 10.1753,+ 10.1753+ ],+ [+ 8.5849,+ 11.188+ ],+ [+ 7.195,+ 12.4621+ ],+ [+ 5.3967,+ 13.0287+ ],+ [+ 3.7244,+ 13.8997+ ],+ [+ 1.8407,+ 13.9816+ ],+ [+ 0.0,+ 14.39+ ],+ [+ -1.8407,+ 13.9816+ ],+ [+ -3.7244,+ 13.8997+ ],+ [+ -5.3967,+ 13.0287+ ],+ [+ -7.195,+ 12.4621+ ],+ [+ -8.5849,+ 11.188+ ],+ [+ -10.1753,+ 10.1753+ ],+ [+ -11.188,+ 8.5849+ ],+ [+ -12.4621,+ 7.195+ ],+ [+ -13.0287,+ 5.3967+ ],+ [+ -13.8997,+ 3.7244+ ],+ [+ -13.9816,+ 1.8407+ ],+ [+ -14.39,+ 0.0+ ],+ [+ -13.9816,+ -1.8407+ ],+ [+ -13.8997,+ -3.7244+ ],+ [+ -13.0287,+ -5.3967+ ],+ [+ -12.4621,+ -7.195+ ],+ [+ -11.188,+ -8.5849+ ],+ [+ -10.1753,+ -10.1753+ ],+ [+ -8.5849,+ -11.188+ ],+ [+ -7.195,+ -12.4621+ ],+ [+ -5.3967,+ -13.0287+ ],+ [+ -3.7244,+ -13.8997+ ],+ [+ -1.8407,+ -13.9816+ ],+ [+ -0.0,+ -14.39+ ],+ [+ 1.8407,+ -13.9816+ ],+ [+ 3.7244,+ -13.8997+ ],+ [+ 5.3967,+ -13.0287+ ],+ [+ 7.195,+ -12.4621+ ],+ [+ 8.5849,+ -11.188+ ],+ [+ 10.1753,+ -10.1753+ ],+ [+ 11.188,+ -8.5849+ ],+ [+ 12.4621,+ -7.195+ ],+ [+ 13.0287,+ -5.3967+ ],+ [+ 13.8997,+ -3.7244+ ],+ [+ 13.9816,+ -1.8407+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.loft",+ "params": {+ "sections": [+ {+ "sketch": "ConeLo"+ },+ {+ "sketch": "ConeHi"+ }+ ],+ "operation": "new",+ "body_name": "Cone",+ "name": "Cone"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "-2",+ "name": "ConeInLo"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 115.8304,+ 0.0+ ],+ [+ 112.5209,+ 14.8137+ ],+ [+ 111.8836,+ 29.9791+ ],+ [+ 104.8528,+ 43.4314+ ],+ [+ 100.3121,+ 57.9152+ ],+ [+ 90.0391,+ 69.0894+ ],+ [+ 81.9045,+ 81.9045+ ],+ [+ 69.0894,+ 90.0391+ ],+ [+ 57.9152,+ 100.3121+ ],+ [+ 43.4314,+ 104.8528+ ],+ [+ 29.9791,+ 111.8836+ ],+ [+ 14.8137,+ 112.5209+ ],+ [+ 0.0,+ 115.8304+ ],+ [+ -14.8137,+ 112.5209+ ],+ [+ -29.9791,+ 111.8836+ ],+ [+ -43.4314,+ 104.8528+ ],+ [+ -57.9152,+ 100.3121+ ],+ [+ -69.0894,+ 90.0391+ ],+ [+ -81.9045,+ 81.9045+ ],+ [+ -90.0391,+ 69.0894+ ],+ [+ -100.3121,+ 57.9152+ ],+ [+ -104.8528,+ 43.4314+ ],+ [+ -111.8836,+ 29.9791+ ],+ [+ -112.5209,+ 14.8137+ ],+ [+ -115.8304,+ 0.0+ ],+ [+ -112.5209,+ -14.8137+ ],+ [+ -111.8836,+ -29.9791+ ],+ [+ -104.8528,+ -43.4314+ ],+ [+ -100.3121,+ -57.9152+ ],+ [+ -90.0391,+ -69.0894+ ],+ [+ -81.9045,+ -81.9045+ ],+ [+ -69.0894,+ -90.0391+ ],+ [+ -57.9152,+ -100.3121+ ],+ [+ -43.4314,+ -104.8528+ ],+ [+ -29.9791,+ -111.8836+ ],+ [+ -14.8137,+ -112.5209+ ],+ [+ -0.0,+ -115.8304+ ],+ [+ 14.8137,+ -112.5209+ ],+ [+ 29.9791,+ -111.8836+ ],+ [+ 43.4314,+ -104.8528+ ],+ [+ 57.9152,+ -100.3121+ ],+ [+ 69.0894,+ -90.0391+ ],+ [+ 81.9045,+ -81.9045+ ],+ [+ 90.0391,+ -69.0894+ ],+ [+ 100.3121,+ -57.9152+ ],+ [+ 104.8528,+ -43.4314+ ],+ [+ 111.8836,+ -29.9791+ ],+ [+ 112.5209,+ -14.8137+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "89.3",+ "name": "ConeInHi"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 12.1544,+ 0.0+ ],+ [+ 11.7876,+ 1.5519+ ],+ [+ 11.7403,+ 3.1458+ ],+ [+ 10.9843,+ 4.5499+ ],+ [+ 10.5261,+ 6.0772+ ],+ [+ 9.4325,+ 7.2378+ ],+ [+ 8.5945,+ 8.5945+ ],+ [+ 7.2378,+ 9.4325+ ],+ [+ 6.0772,+ 10.5261+ ],+ [+ 4.5499,+ 10.9843+ ],+ [+ 3.1458,+ 11.7403+ ],+ [+ 1.5519,+ 11.7876+ ],+ [+ 0.0,+ 12.1544+ ],+ [+ -1.5519,+ 11.7876+ ],+ [+ -3.1458,+ 11.7403+ ],+ [+ -4.5499,+ 10.9843+ ],+ [+ -6.0772,+ 10.5261+ ],+ [+ -7.2378,+ 9.4325+ ],+ [+ -8.5945,+ 8.5945+ ],+ [+ -9.4325,+ 7.2378+ ],+ [+ -10.5261,+ 6.0772+ ],+ [+ -10.9843,+ 4.5499+ ],+ [+ -11.7403,+ 3.1458+ ],+ [+ -11.7876,+ 1.5519+ ],+ [+ -12.1544,+ 0.0+ ],+ [+ -11.7876,+ -1.5519+ ],+ [+ -11.7403,+ -3.1458+ ],+ [+ -10.9843,+ -4.5499+ ],+ [+ -10.5261,+ -6.0772+ ],+ [+ -9.4325,+ -7.2378+ ],+ [+ -8.5945,+ -8.5945+ ],+ [+ -7.2378,+ -9.4325+ ],+ [+ -6.0772,+ -10.5261+ ],+ [+ -4.5499,+ -10.9843+ ],+ [+ -3.1458,+ -11.7403+ ],+ [+ -1.5519,+ -11.7876+ ],+ [+ -0.0,+ -12.1544+ ],+ [+ 1.5519,+ -11.7876+ ],+ [+ 3.1458,+ -11.7403+ ],+ [+ 4.5499,+ -10.9843+ ],+ [+ 6.0772,+ -10.5261+ ],+ [+ 7.2378,+ -9.4325+ ],+ [+ 8.5945,+ -8.5945+ ],+ [+ 9.4325,+ -7.2378+ ],+ [+ 10.5261,+ -6.0772+ ],+ [+ 10.9843,+ -4.5499+ ],+ [+ 11.7403,+ -3.1458+ ],+ [+ 11.7876,+ -1.5519+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.loft",+ "params": {+ "sections": [+ {+ "sketch": "ConeInLo"+ },+ {+ "sketch": "ConeInHi"+ }+ ],+ "operation": "new",+ "body_name": "ConeIn",+ "name": "ConeIn"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "Cone",+ "tools": [+ "ConeIn"+ ],+ "operation": "cut"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "-1",+ "name": "LipLo"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 114.4444,+ 0.0+ ],+ [+ 111.196,+ 14.6392+ ],+ [+ 110.5448,+ 29.6204+ ],+ [+ 103.6182,+ 42.9201+ ],+ [+ 99.1118,+ 57.2222+ ],+ [+ 88.979,+ 68.276+ ],+ [+ 80.9244,+ 80.9244+ ],+ [+ 68.276,+ 88.979+ ],+ [+ 57.2222,+ 99.1118+ ],+ [+ 42.9201,+ 103.6182+ ],+ [+ 29.6204,+ 110.5448+ ],+ [+ 14.6392,+ 111.196+ ],+ [+ 0.0,+ 114.4444+ ],+ [+ -14.6392,+ 111.196+ ],+ [+ -29.6204,+ 110.5448+ ],+ [+ -42.9201,+ 103.6182+ ],+ [+ -57.2222,+ 99.1118+ ],+ [+ -68.276,+ 88.979+ ],+ [+ -80.9244,+ 80.9244+ ],+ [+ -88.979,+ 68.276+ ],+ [+ -99.1118,+ 57.2222+ ],+ [+ -103.6182,+ 42.9201+ ],+ [+ -110.5448,+ 29.6204+ ],+ [+ -111.196,+ 14.6392+ ],+ [+ -114.4444,+ 0.0+ ],+ [+ -111.196,+ -14.6392+ ],+ [+ -110.5448,+ -29.6204+ ],+ [+ -103.6182,+ -42.9201+ ],+ [+ -99.1118,+ -57.2222+ ],+ [+ -88.979,+ -68.276+ ],+ [+ -80.9244,+ -80.9244+ ],+ [+ -68.276,+ -88.979+ ],+ [+ -57.2222,+ -99.1118+ ],+ [+ -42.9201,+ -103.6182+ ],+ [+ -29.6204,+ -110.5448+ ],+ [+ -14.6392,+ -111.196+ ],+ [+ -0.0,+ -114.4444+ ],+ [+ 14.6392,+ -111.196+ ],+ [+ 29.6204,+ -110.5448+ ],+ [+ 42.9201,+ -103.6182+ ],+ [+ 57.2222,+ -99.1118+ ],+ [+ 68.276,+ -88.979+ ],+ [+ 80.9244,+ -80.9244+ ],+ [+ 88.979,+ -68.276+ ],+ [+ 99.1118,+ -57.2222+ ],+ [+ 103.6182,+ -42.9201+ ],+ [+ 110.5448,+ -29.6204+ ],+ [+ 111.196,+ -14.6392+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "6",+ "name": "LipHi"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 120.0,+ 0.0+ ],+ [+ 116.5939,+ 15.3499+ ],+ [+ 115.9111,+ 31.0583+ ],+ [+ 108.6482,+ 45.0036+ ],+ [+ 103.923,+ 60.0+ ],+ [+ 93.2984,+ 71.5903+ ],+ [+ 84.8528,+ 84.8528+ ],+ [+ 71.5903,+ 93.2984+ ],+ [+ 60.0,+ 103.923+ ],+ [+ 45.0036,+ 108.6482+ ],+ [+ 31.0583,+ 115.9111+ ],+ [+ 15.3499,+ 116.5939+ ],+ [+ 0.0,+ 120.0+ ],+ [+ -15.3499,+ 116.5939+ ],+ [+ -31.0583,+ 115.9111+ ],+ [+ -45.0036,+ 108.6482+ ],+ [+ -60.0,+ 103.923+ ],+ [+ -71.5903,+ 93.2984+ ],+ [+ -84.8528,+ 84.8528+ ],+ [+ -93.2984,+ 71.5903+ ],+ [+ -103.923,+ 60.0+ ],+ [+ -108.6482,+ 45.0036+ ],+ [+ -115.9111,+ 31.0583+ ],+ [+ -116.5939,+ 15.3499+ ],+ [+ -120.0,+ 0.0+ ],+ [+ -116.5939,+ -15.3499+ ],+ [+ -115.9111,+ -31.0583+ ],+ [+ -108.6482,+ -45.0036+ ],+ [+ -103.923,+ -60.0+ ],+ [+ -93.2984,+ -71.5903+ ],+ [+ -84.8528,+ -84.8528+ ],+ [+ -71.5903,+ -93.2984+ ],+ [+ -60.0,+ -103.923+ ],+ [+ -45.0036,+ -108.6482+ ],+ [+ -31.0583,+ -115.9111+ ],+ [+ -15.3499,+ -116.5939+ ],+ [+ -0.0,+ -120.0+ ],+ [+ 15.3499,+ -116.5939+ ],+ [+ 31.0583,+ -115.9111+ ],+ [+ 45.0036,+ -108.6482+ ],+ [+ 60.0,+ -103.923+ ],+ [+ 71.5903,+ -93.2984+ ],+ [+ 84.8528,+ -84.8528+ ],+ [+ 93.2984,+ -71.5903+ ],+ [+ 103.923,+ -60.0+ ],+ [+ 108.6482,+ -45.0036+ ],+ [+ 115.9111,+ -31.0583+ ],+ [+ 116.5939,+ -15.3499+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.loft",+ "params": {+ "sections": [+ {+ "sketch": "LipLo"+ },+ {+ "sketch": "LipHi"+ }+ ],+ "operation": "new",+ "body_name": "Lip",+ "name": "Lip"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "-2",+ "name": "LipInLo"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 112.5508,+ 0.0+ ],+ [+ 109.3343,+ 14.3941+ ],+ [+ 108.7157,+ 29.1303+ ],+ [+ 101.8834,+ 42.2015+ ],+ [+ 97.4718,+ 56.2754+ ],+ [+ 87.4892,+ 67.1329+ ],+ [+ 79.5854,+ 79.5854+ ],+ [+ 67.1329,+ 87.4892+ ],+ [+ 56.2754,+ 97.4718+ ],+ [+ 42.2015,+ 101.8834+ ],+ [+ 29.1303,+ 108.7157+ ],+ [+ 14.3941,+ 109.3343+ ],+ [+ 0.0,+ 112.5508+ ],+ [+ -14.3941,+ 109.3343+ ],+ [+ -29.1303,+ 108.7157+ ],+ [+ -42.2015,+ 101.8834+ ],+ [+ -56.2754,+ 97.4718+ ],+ [+ -67.1329,+ 87.4892+ ],+ [+ -79.5854,+ 79.5854+ ],+ [+ -87.4892,+ 67.1329+ ],+ [+ -97.4718,+ 56.2754+ ],+ [+ -101.8834,+ 42.2015+ ],+ [+ -108.7157,+ 29.1303+ ],+ [+ -109.3343,+ 14.3941+ ],+ [+ -112.5508,+ 0.0+ ],+ [+ -109.3343,+ -14.3941+ ],+ [+ -108.7157,+ -29.1303+ ],+ [+ -101.8834,+ -42.2015+ ],+ [+ -97.4718,+ -56.2754+ ],+ [+ -87.4892,+ -67.1329+ ],+ [+ -79.5854,+ -79.5854+ ],+ [+ -67.1329,+ -87.4892+ ],+ [+ -56.2754,+ -97.4718+ ],+ [+ -42.2015,+ -101.8834+ ],+ [+ -29.1303,+ -108.7157+ ],+ [+ -14.3941,+ -109.3343+ ],+ [+ -0.0,+ -112.5508+ ],+ [+ 14.3941,+ -109.3343+ ],+ [+ 29.1303,+ -108.7157+ ],+ [+ 42.2015,+ -101.8834+ ],+ [+ 56.2754,+ -97.4718+ ],+ [+ 67.1329,+ -87.4892+ ],+ [+ 79.5854,+ -79.5854+ ],+ [+ 87.4892,+ -67.1329+ ],+ [+ 97.4718,+ -56.2754+ ],+ [+ 101.8834,+ -42.2015+ ],+ [+ 108.7157,+ -29.1303+ ],+ [+ 109.3343,+ -14.3941+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "offset": "7",+ "name": "LipInHi"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 119.6937,+ 0.0+ ],+ [+ 116.2745,+ 15.3078+ ],+ [+ 115.6152,+ 30.979+ ],+ [+ 108.3505,+ 44.8803+ ],+ [+ 103.6577,+ 59.8468+ ],+ [+ 93.0427,+ 71.3942+ ],+ [+ 84.6362,+ 84.6362+ ],+ [+ 71.3942,+ 93.0427+ ],+ [+ 59.8468,+ 103.6577+ ],+ [+ 44.8803,+ 108.3505+ ],+ [+ 30.979,+ 115.6152+ ],+ [+ 15.3078,+ 116.2745+ ],+ [+ 0.0,+ 119.6937+ ],+ [+ -15.3078,+ 116.2745+ ],+ [+ -30.979,+ 115.6152+ ],+ [+ -44.8803,+ 108.3505+ ],+ [+ -59.8468,+ 103.6577+ ],+ [+ -71.3942,+ 93.0427+ ],+ [+ -84.6362,+ 84.6362+ ],+ [+ -93.0427,+ 71.3942+ ],+ [+ -103.6577,+ 59.8468+ ],+ [+ -108.3505,+ 44.8803+ ],+ [+ -115.6152,+ 30.979+ ],+ [+ -116.2745,+ 15.3078+ ],+ [+ -119.6937,+ 0.0+ ],+ [+ -116.2745,+ -15.3078+ ],+ [+ -115.6152,+ -30.979+ ],+ [+ -108.3505,+ -44.8803+ ],+ [+ -103.6577,+ -59.8468+ ],+ [+ -93.0427,+ -71.3942+ ],+ [+ -84.6362,+ -84.6362+ ],+ [+ -71.3942,+ -93.0427+ ],+ [+ -59.8468,+ -103.6577+ ],+ [+ -44.8803,+ -108.3505+ ],+ [+ -30.979,+ -115.6152+ ],+ [+ -15.3078,+ -116.2745+ ],+ [+ -0.0,+ -119.6937+ ],+ [+ 15.3078,+ -116.2745+ ],+ [+ 30.979,+ -115.6152+ ],+ [+ 44.8803,+ -108.3505+ ],+ [+ 59.8468,+ -103.6577+ ],+ [+ 71.3942,+ -93.0427+ ],+ [+ 84.6362,+ -84.6362+ ],+ [+ 93.0427,+ -71.3942+ ],+ [+ 103.6577,+ -59.8468+ ],+ [+ 108.3505,+ -44.8803+ ],+ [+ 115.6152,+ -30.979+ ],+ [+ 116.2745,+ -15.3078+ ]+ ],+ "closed": true,+ "infer": false+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.loft",+ "params": {+ "sections": [+ {+ "sketch": "LipInLo"+ },+ {+ "sketch": "LipInHi"+ }+ ],+ "operation": "new",+ "body_name": "LipIn",+ "name": "LipIn"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "Lip",+ "tools": [+ "LipIn"+ ],+ "operation": "cut"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "Cone",+ "tools": [+ "Lip"+ ],+ "operation": "join"+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4654-split-body-by-its-own-face-extended/expected.json b/tests/kernel-cases/booleans/4654-split-body-by-its-own-face-extended/expected.jsonnew file mode 100644index 0000000000..038bb0c901--- /dev/null+++ b/tests/kernel-cases/booleans/4654-split-body-by-its-own-face-extended/expected.json@@ -0,0 +1,10 @@+{+ "sources": [+ "tangency-labs/solidcraft#4654"+ ],+ "what": "Split Body of an L-shaped body with one of its own faces as the tool (the column's side x = 15, its surface extended through the base): truck panicked ('split body: Option::unwrap() on None')",+ "source": "analytic",+ "method": "the plane x = 15 cuts the base under the column: the column with the base's left part (15*20*30 = 9000) and the base's right part (25*20*10 = 5000). Two bodies, V = 14000",+ "body_count": 2,+ "volume_mm3": 14000.0+}diff --git a/tests/kernel-cases/booleans/4654-split-body-by-its-own-face-extended/recipe.json b/tests/kernel-cases/booleans/4654-split-body-by-its-own-face-extended/recipe.jsonnew file mode 100644index 0000000000..aec4e90b5d--- /dev/null+++ b/tests/kernel-cases/booleans/4654-split-body-by-its-own-face-extended/recipe.json@@ -0,0 +1,49 @@+{+ "commands": [+ {+ "command": "solid.box",+ "params": {+ "corner": [+ 0,+ 0,+ 0+ ],+ "length": 40,+ "width": 20,+ "height": 10,+ "body_name": "L"+ }+ },+ {+ "command": "solid.box",+ "params": {+ "corner": [+ 0,+ 0,+ 10+ ],+ "length": 15,+ "width": 20,+ "height": 20,+ "operation": "join",+ "targets": [+ "L"+ ]+ }+ },+ {+ "command": "solid.split_body",+ "params": {+ "body": "L",+ "tool": {+ "body": "L",+ "point": [+ 15,+ 10,+ 20+ ]+ }+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4701-join-disc-on-tapered-ring/expected.json b/tests/kernel-cases/booleans/4701-join-disc-on-tapered-ring/expected.jsonnew file mode 100644index 0000000000..afedef8af0--- /dev/null+++ b/tests/kernel-cases/booleans/4701-join-disc-on-tapered-ring/expected.json@@ -0,0 +1,10 @@+{+ "sources": [+ "tangency-labs/solidcraft#4701"+ ],+ "what": "a 3 mm disc (r23) joined on the top face of a ring extruded 14 mm with a 10 deg outward taper (r 18.5 growing, bore 13.75 shrinking): 202 s in truck before the right result",+ "source": "analytic",+ "method": "the ring: frustum r 18.5 -> 18.5 + 14 tan10 less frustum r 13.75 -> 13.75 - 14 tan10, both 14 high (pi h/3 (a^2+ab+b^2)); the cap pi 23^2 3 covers the ring's top (r 11.28..20.97) and its bore",+ "body_count": 1,+ "volume_mm3": 15224.7481+}diff --git a/tests/kernel-cases/booleans/4701-join-disc-on-tapered-ring/recipe.json b/tests/kernel-cases/booleans/4701-join-disc-on-tapered-ring/recipe.jsonnew file mode 100644index 0000000000..2395e00a05--- /dev/null+++ b/tests/kernel-cases/booleans/4701-join-disc-on-tapered-ring/recipe.json@@ -0,0 +1,106 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "name": "Outer"+ }+ },+ {+ "command": "sketch.circle.center",+ "params": {+ "center": [+ 0,+ 0+ ],+ "radius": 18.5+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Outer",+ "distance": 14,+ "taper": "10 deg",+ "body_name": "Ring"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "name": "Inner"+ }+ },+ {+ "command": "sketch.circle.center",+ "params": {+ "center": [+ 0,+ 0+ ],+ "radius": 13.75+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Inner",+ "distance": 14,+ "taper": "-10 deg",+ "operation": "cut",+ "targets": [+ "Ring"+ ]+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "face": [+ 16,+ 0,+ 14+ ]+ },+ "name": "Cap",+ "project_edges": false+ }+ },+ {+ "command": "sketch.circle.center",+ "params": {+ "center": [+ 0,+ 0+ ],+ "radius": 23+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Cap",+ "distance": 3,+ "operation": "join",+ "targets": [+ "Ring"+ ]+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4825-tapered-pocket-with-small-corner-radius/expected.json b/tests/kernel-cases/booleans/4825-tapered-pocket-with-small-corner-radius/expected.jsonnew file mode 100644index 0000000000..a85917352f--- /dev/null+++ b/tests/kernel-cases/booleans/4825-tapered-pocket-with-small-corner-radius/expected.json@@ -0,0 +1,11 @@+{+ "sources": [+ "tangency-labs/solidcraft#4825"+ ],+ "what": "a 5 mm pocket cut from a hull's top face with a 30 deg taper (growing with depth) from a 282x176 outline with r2 corners: truck refused it ('the taper closes the profile'), as its run-on behind the start face narrowed past the corner radius",+ "source": "analytic",+ "method": "hull 318x212 r8 corners, z 46..156: (318*212 - (4-pi)*64)*110. The pocket at depth t is the outline offset by s = t*tan30: area (282+2s)(176+2s) - (4-pi)(2+s)^2, integrated over t 0..5 = 254772.3456. Faces: hull 4 sides + 4 corner cylinders + top + bottom, pocket 4 sloped planes + 4 cones + floor = 19",+ "body_count": 1,+ "faces": 19,+ "volume_mm3": 7154944.467+}diff --git a/tests/kernel-cases/booleans/4825-tapered-pocket-with-small-corner-radius/recipe.json b/tests/kernel-cases/booleans/4825-tapered-pocket-with-small-corner-radius/recipe.jsonnew file mode 100644index 0000000000..34eaa751a9--- /dev/null+++ b/tests/kernel-cases/booleans/4825-tapered-pocket-with-small-corner-radius/recipe.json@@ -0,0 +1,87 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "name": "Outline",+ "offset": 46,+ "project_edges": false+ }+ },+ {+ "command": "sketch.rectangle.rounded",+ "params": {+ "p0": [+ -159,+ -106+ ],+ "p1": [+ 159,+ 106+ ],+ "radius": 8+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Outline",+ "distance": 110,+ "body_name": "Hull"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "name": "Ledge",+ "offset": 156,+ "project_edges": false+ }+ },+ {+ "command": "sketch.rectangle.rounded",+ "params": {+ "p0": [+ -141,+ -88+ ],+ "p1": [+ 141,+ 88+ ],+ "radius": 2+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Ledge",+ "distance": 5,+ "direction": "negative",+ "taper": "30 deg",+ "profiles": [+ {+ "point": [+ 0,+ 0+ ]+ }+ ],+ "operation": "cut",+ "targets": [+ "Hull"+ ]+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/4829-cut-from-flat-top-bounded-by-fillet-edge/expected.json b/tests/kernel-cases/booleans/4829-cut-from-flat-top-bounded-by-fillet-edge/expected.jsonnew file mode 100644index 0000000000..3a1d106a6f--- /dev/null+++ b/tests/kernel-cases/booleans/4829-cut-from-flat-top-bounded-by-fillet-edge/expected.json@@ -0,0 +1,11 @@+{+ "sources": [+ "tangency-labs/solidcraft#4829"+ ],+ "what": "a cylinder r10 x 40 with its top edge filleted r2, cut 14 mm down from its flat top face (the R8 disc, bounded by the fillet's edge): ~30 s, then 'boolean Cut: no result'",+ "source": "analytic",+ "method": "the round removes the corner region (1-pi/4) 2^2 at radius 10 - (2 - (2/6)/(1-pi/4)) (Pappus); the cut removes the R8 disc x 14: V = pi 100 40 - removed - pi 64 14. The top face is used up: faces side, bottom, round, pocket wall, pocket floor = 5",+ "body_count": 1,+ "faces": 5,+ "volume_mm3": 9699.9778+}diff --git a/tests/kernel-cases/booleans/4829-cut-from-flat-top-bounded-by-fillet-edge/recipe.json b/tests/kernel-cases/booleans/4829-cut-from-flat-top-bounded-by-fillet-edge/recipe.jsonnew file mode 100644index 0000000000..e1218cc80d--- /dev/null+++ b/tests/kernel-cases/booleans/4829-cut-from-flat-top-bounded-by-fillet-edge/recipe.json@@ -0,0 +1,39 @@+{+ "commands": [+ {+ "command": "solid.cylinder",+ "params": {+ "radius": 10,+ "height": 40,+ "body_name": "Body1"+ }+ },+ {+ "command": "solid.fillet",+ "params": {+ "edges": [+ [+ 10,+ 0,+ 40+ ]+ ],+ "radius": 2+ }+ },+ {+ "command": "solid.extrude",+ "params": {+ "face": [+ 1.77,+ 1.39,+ 40+ ],+ "face_body": "Body1",+ "direction": "negative",+ "distance": 14,+ "operation": "cut"+ }+ }+ ]+}diff --git a/tests/kernel-cases/booleans/skipped-4161.json b/tests/kernel-cases/booleans/skipped-4161.jsonindex 2cd3dd4439..b6e886ec7f 100644--- a/tests/kernel-cases/booleans/skipped-4161.json+++ b/tests/kernel-cases/booleans/skipped-4161.json@@ -142,5 +142,253 @@{"source": "tangency-labs/solidcraft#4424","why": "no geometry: a cut in a component other than the active one (document, dup of #4639)"+ },+ {+ "source": "tangency-labs/solidcraft#4433",+ "why": "no geometry: a sheet-metal hole the flat pattern can't keep is refused by design"+ },+ {+ "source": "tangency-labs/solidcraft#4434",+ "why": "duplicate of the rig's join-that-meets-nothing case (#2896): a join apart from the body keeps it as a lump, without a warning"+ },+ {+ "source": "tangency-labs/solidcraft#4435",+ "why": "no geometry: a sketch pattern's count parameter link not kept (sketch)"+ },+ {+ "source": "tangency-labs/solidcraft#4437",+ "why": "no reproduction: a screenshot of an unknown part, no message"+ },+ {+ "source": "tangency-labs/solidcraft#4443",+ "why": "no geometry: a saved model cache refused after a boolean retry (document)"+ },+ {+ "source": "tangency-labs/solidcraft#4448",+ "why": "no reproduction: a body patterned about a tilted axis, the body and the wrong result not described"+ },+ {+ "source": "tangency-labs/solidcraft#4458",+ "why": "no reproduction: a mirror redefined on an unknown part, the result not described"+ },+ {+ "source": "tangency-labs/solidcraft#4477",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4481",+ "why": "no reproduction: last command only (a hole), the unexpected result not described"+ },+ {+ "source": "tangency-labs/solidcraft#4488",+ "why": "no kernel geometry: Emboss refuses a concave cylinder face (the emboss command's stated limit)"+ },+ {+ "source": "tangency-labs/solidcraft#4489",+ "why": "UI only: Move point-to-point takes the rim point of a picked circle"+ },+ {+ "source": "tangency-labs/solidcraft#4502",+ "why": "render: the sketch viewport turns blue on old Intel graphics"+ },+ {+ "source": "tangency-labs/solidcraft#4509",+ "why": "no geometry: an offset plane can't attach to a face whose history is ambiguous (document, dup of #4325)"+ },+ {+ "source": "tangency-labs/solidcraft#4516",+ "why": "no reproduction: a sketch loop past the profile curve budget; 400- and 600-segment loops extrude, the sketch is not given"+ },+ {+ "source": "tangency-labs/solidcraft#4523",+ "why": "no geometry: a join onto a mesh body is refused by design (dup of #3038)"+ },+ {+ "source": "tangency-labs/solidcraft#4530",+ "why": "no reproduction: last command only (a join of two bodies), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4532",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4534",+ "why": "no reproduction: \"profile loop is not closed\" on an unknown sketch"+ },+ {+ "source": "tangency-labs/solidcraft#4544",+ "why": "UI only: a Norwegian translation"+ },+ {+ "source": "tangency-labs/solidcraft#4551",+ "why": "no reproduction: last command and a screenshot of an unknown part"+ },+ {+ "source": "tangency-labs/solidcraft#4557",+ "why": "no reproduction: STL export T-junctions on a user's STEP-imported part (the file is the reporter's)"+ },+ {+ "source": "tangency-labs/solidcraft#4563",+ "why": "UI only: a section hatch option"+ },+ {+ "source": "tangency-labs/solidcraft#4572",+ "why": "no kernel geometry: a join from a sketch on a face defaults to that face's body (target choice)"+ },+ {+ "source": "tangency-labs/solidcraft#4582",+ "why": "UI only: shortcut names"+ },+ {+ "source": "tangency-labs/solidcraft#4584",+ "why": "no geometry: an offset plane can't attach to a face whose history is ambiguous (document, dup of #4325)"+ },+ {+ "source": "tangency-labs/solidcraft#4589",+ "why": "UI only: expression suggestions over a slider"+ },+ {+ "source": "tangency-labs/solidcraft#4593",+ "why": "no geometry: a Rib can't be patterned yet (a stated limit)"+ },+ {+ "source": "tangency-labs/solidcraft#4594",+ "why": "no reproduction: a projected-face warning in a sketch, no steps or design"+ },+ {+ "source": "tangency-labs/solidcraft#4597",+ "why": "no reproduction: last command only (a 20 mm cut), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4600",+ "why": "no reproduction: last command only (a 20 mm cut), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4619",+ "why": "no kernel geometry: Emboss on a cylinder takes lines square to the axis only (the emboss command's stated limit)"+ },+ {+ "source": "tangency-labs/solidcraft#4621",+ "why": "render: section caps of touching bodies drawn in patches"+ },+ {+ "source": "tangency-labs/solidcraft#4624",+ "why": "no reproduction: last command only (a two-sided join), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4636",+ "why": "UI only: 3D mouse navigation"+ },+ {+ "source": "tangency-labs/solidcraft#4639",+ "why": "no geometry: a cut in a component other than the active one (document)"+ },+ {+ "source": "tangency-labs/solidcraft#4643",+ "why": "UI only: extrude dialog keyboard focus after a profile click"+ },+ {+ "source": "tangency-labs/solidcraft#4658",+ "why": "UI only: ribbon recomputes its panels every frame"+ },+ {+ "source": "tangency-labs/solidcraft#4685",+ "why": "needs the user design: a 20-feature shelled part cut by a 2.7 mm3 body; no small stand-in"+ },+ {+ "source": "tangency-labs/solidcraft#4706",+ "why": "needs the user design: a housing of tangent arcs with cut pockets; no small stand-in shows the same geometry"+ },+ {+ "source": "tangency-labs/solidcraft#4714",+ "why": "no reproduction: Snap Fit on one half of a split user part, the position not on the named body"+ },+ {+ "source": "tangency-labs/solidcraft#4723",+ "why": "no geometry: holes on an unfolded sheet-metal flat pattern are refused by design"+ },+ {+ "source": "tangency-labs/solidcraft#4728",+ "why": "no reproduction: a test hinge of two bodies from one sketch, screenshots only"+ },+ {+ "source": "tangency-labs/solidcraft#4731",+ "why": "no geometry: a sheet-metal cut the flat pattern can't keep is refused by design"+ },+ {+ "source": "tangency-labs/solidcraft#4733",+ "why": "no reproduction: last command only (a face cut on an unknown part)"+ },+ {+ "source": "tangency-labs/solidcraft#4741",+ "why": "no geometry: a construction axis as the pattern axis (command parameters, dup of #2885)"+ },+ {+ "source": "tangency-labs/solidcraft#4750",+ "why": "no geometry: a two-curve sketch extend (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4753",+ "why": "no geometry: five text profiles were picked where one was meant (user selection)"+ },+ {+ "source": "tangency-labs/solidcraft#4755",+ "why": "no reproduction: last command only (a fender cut on an unknown part)"+ },+ {+ "source": "tangency-labs/solidcraft#4756",+ "why": "no reproduction: a DXF logo cut from a user's curved face (105 freeform faces), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4760",+ "why": "no geometry: a sketch weld tool (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4761",+ "why": "no kernel geometry: Emboss refuses a conical face (the emboss command's stated limit)"+ },+ {+ "source": "tangency-labs/solidcraft#4763",+ "why": "no kernel geometry: path pattern copies placed in the wrong frame (pattern placement, engine)"+ },+ {+ "source": "tangency-labs/solidcraft#4783",+ "why": "no geometry: material name and density looked up apart (document)"+ },+ {+ "source": "tangency-labs/solidcraft#4798",+ "why": "no geometry: an edge-midpoint rectangle (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4800",+ "why": "no reproduction: a cut not updating after a sketch edit, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4803",+ "why": "no reproduction: the second defect is shown only by screenshots of the user's part"+ },+ {+ "source": "tangency-labs/solidcraft#4805",+ "why": "no geometry: an offset plane can't attach to a face whose history is ambiguous (document, dup of #4325)"+ },+ {+ "source": "tangency-labs/solidcraft#4807",+ "why": "UI only: a placed hole shows a drag cursor"+ },+ {+ "source": "tangency-labs/solidcraft#4810",+ "why": "no geometry: no circle-to-circle sketch dimension (dup of #4064)"+ },+ {+ "source": "tangency-labs/solidcraft#4818",+ "why": "UI only: first-run setup (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4826",+ "why": "no geometry: user error (a line not horizontal), withdrawn"+ },+ {+ "source": "tangency-labs/solidcraft#4827",+ "why": "UI only: draft corner rules in the dialog (feature request)"}]diff --git a/tests/kernel-cases/crashes/4542-join-fluted-wall-on-revolved-base/expected.json b/tests/kernel-cases/crashes/4542-join-fluted-wall-on-revolved-base/expected.jsonnew file mode 100644index 0000000000..810c21b84c--- /dev/null+++ b/tests/kernel-cases/crashes/4542-join-fluted-wall-on-revolved-base/expected.json@@ -0,0 +1,9 @@+{+ "sources": [+ "tangency-labs/solidcraft#4542"+ ],+ "what": "a fluted cup wall (a 72-point periodic fit spline round r 31.5..32.5 outside, a circle r 25 inside) extruded 90 mm as a join onto the top face of a revolved base disc of r 32: the app hung in the boolean",+ "source": "invariants",+ "method": "the wall's ring stands on the base's top face (z = 7), overlapping it between r 25 and the disc's rim and overhanging it where the flutes pass r 32, so the join is one connected solid: one valid closed body. The spline's area is not closed-form, so the volume is not graded",+ "body_count": 1+}diff --git a/tests/kernel-cases/crashes/4542-join-fluted-wall-on-revolved-base/recipe.json b/tests/kernel-cases/crashes/4542-join-fluted-wall-on-revolved-base/recipe.jsonnew file mode 100644index 0000000000..2fdac1356d--- /dev/null+++ b/tests/kernel-cases/crashes/4542-join-fluted-wall-on-revolved-base/recipe.json@@ -0,0 +1,419 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "origin": [+ 0,+ 0,+ 0+ ],+ "x_dir": [+ 1,+ 0,+ 0+ ],+ "y_dir": [+ 0,+ 0,+ 1+ ]+ },+ "name": "Base"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 0,+ 0+ ],+ [+ 25,+ 0+ ]+ ]+ }+ },+ {+ "command": "sketch.arc.three_point",+ "params": {+ "start": [+ 25,+ 0+ ],+ "through": [+ 29.5,+ 1.5+ ],+ "end": [+ 32,+ 7+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 32,+ 7+ ],+ [+ 0,+ 7+ ],+ [+ 0,+ 0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.revolve",+ "params": {+ "sketch": "Base",+ "axis": "y",+ "body_name": "Cup"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY",+ "name": "Wall",+ "offset": 7+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 32.5,+ 0.0+ ],+ [+ 32.127,+ 2.811+ ],+ [+ 31.268,+ 5.513+ ],+ [+ 30.427,+ 8.153+ ],+ [+ 29.835,+ 10.859+ ],+ [+ 29.228,+ 13.629+ ],+ [+ 28.146,+ 16.25+ ],+ [+ 26.418,+ 18.498+ ],+ [+ 24.322,+ 20.409+ ],+ [+ 22.274,+ 22.274+ ],+ [+ 20.409,+ 24.322+ ],+ [+ 18.498,+ 26.418+ ],+ [+ 16.25,+ 28.146+ ],+ [+ 13.629,+ 29.228+ ],+ [+ 10.859,+ 29.835+ ],+ [+ 8.153,+ 30.427+ ],+ [+ 5.513,+ 31.268+ ],+ [+ 2.811,+ 32.127+ ],+ [+ 0.0,+ 32.5+ ],+ [+ -2.811,+ 32.127+ ],+ [+ -5.513,+ 31.268+ ],+ [+ -8.153,+ 30.427+ ],+ [+ -10.859,+ 29.835+ ],+ [+ -13.629,+ 29.228+ ],+ [+ -16.25,+ 28.146+ ],+ [+ -18.498,+ 26.418+ ],+ [+ -20.409,+ 24.322+ ],+ [+ -22.274,+ 22.274+ ],+ [+ -24.322,+ 20.409+ ],+ [+ -26.418,+ 18.498+ ],+ [+ -28.146,+ 16.25+ ],+ [+ -29.228,+ 13.629+ ],+ [+ -29.835,+ 10.859+ ],+ [+ -30.427,+ 8.153+ ],+ [+ -31.268,+ 5.513+ ],+ [+ -32.127,+ 2.811+ ],+ [+ -32.5,+ 0.0+ ],+ [+ -32.127,+ -2.811+ ],+ [+ -31.268,+ -5.513+ ],+ [+ -30.427,+ -8.153+ ],+ [+ -29.835,+ -10.859+ ],+ [+ -29.228,+ -13.629+ ],+ [+ -28.146,+ -16.25+ ],+ [+ -26.418,+ -18.498+ ],+ [+ -24.322,+ -20.409+ ],+ [+ -22.274,+ -22.274+ ],+ [+ -20.409,+ -24.322+ ],+ [+ -18.498,+ -26.418+ ],+ [+ -16.25,+ -28.146+ ],+ [+ -13.629,+ -29.228+ ],+ [+ -10.859,+ -29.835+ ],+ [+ -8.153,+ -30.427+ ],+ [+ -5.513,+ -31.268+ ],+ [+ -2.811,+ -32.127+ ],+ [+ -0.0,+ -32.5+ ],+ [+ 2.811,+ -32.127+ ],+ [+ 5.513,+ -31.268+ ],+ [+ 8.153,+ -30.427+ ],+ [+ 10.859,+ -29.835+ ],+ [+ 13.629,+ -29.228+ ],+ [+ 16.25,+ -28.146+ ],+ [+ 18.498,+ -26.418+ ],+ [+ 20.409,+ -24.322+ ],+ [+ 22.274,+ -22.274+ ],+ [+ 24.322,+ -20.409+ ],+ [+ 26.418,+ -18.498+ ],+ [+ 28.146,+ -16.25+ ],+ [+ 29.228,+ -13.629+ ],+ [+ 29.835,+ -10.859+ ],+ [+ 30.427,+ -8.153+ ],+ [+ 31.268,+ -5.513+ ],+ [+ 32.127,+ -2.811+ ]+ ],+ "periodic": true+ }+ },+ {+ "command": "sketch.circle.center",+ "params": {+ "center": [+ 0,+ 0+ ],+ "radius": 25+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Wall",+ "distance": 90,+ "operation": "join",+ "targets": [+ "Cup"+ ]+ }+ }+ ]+}diff --git a/tests/kernel-cases/crashes/4547-join-revolved-rings-touching-along-a-circle/expected.json b/tests/kernel-cases/crashes/4547-join-revolved-rings-touching-along-a-circle/expected.jsonnew file mode 100644index 0000000000..c9a7c62ea5--- /dev/null+++ b/tests/kernel-cases/crashes/4547-join-revolved-rings-touching-along-a-circle/expected.json@@ -0,0 +1,12 @@+{+ "sources": [+ "tangency-labs/solidcraft#4547",+ "tangency-labs/solidcraft#4542"+ ],+ "what": "a join of two revolved rings that touch only along a circle (r 20.5 at z 4: the corner of one ring on the corner of the other): the app hung in the boolean",+ "source": "analytic",+ "method": "ring A r 20..20.5, z 0..4: pi*(20.5^2-20^2)*4 = 254.469; ring B r 20.5..28, z 4..18: pi*(28^2-20.5^2)*14 = 15997.83. They share only the circle r 20.5, z 4, so the join keeps them as two bodies (touching: separate, the default) or refuses cleanly; never a hang",+ "outcome": "solid_or_refused",+ "body_count": 2,+ "volume_mm3": 16253.0296+}diff --git a/tests/kernel-cases/crashes/4547-join-revolved-rings-touching-along-a-circle/recipe.json b/tests/kernel-cases/crashes/4547-join-revolved-rings-touching-along-a-circle/recipe.jsonnew file mode 100644index 0000000000..9ad46f4423--- /dev/null+++ b/tests/kernel-cases/crashes/4547-join-revolved-rings-touching-along-a-circle/recipe.json@@ -0,0 +1,110 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "origin": [+ 0,+ 0,+ 0+ ],+ "x_dir": [+ 1,+ 0,+ 0+ ],+ "y_dir": [+ 0,+ 0,+ 1+ ]+ },+ "name": "A"+ }+ },+ {+ "command": "sketch.rectangle.two_point",+ "params": {+ "p0": [+ 20,+ 0+ ],+ "p1": [+ 20.5,+ 4+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.revolve",+ "params": {+ "sketch": "A",+ "axis": "y",+ "body_name": "RingA"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "origin": [+ 0,+ 0,+ 0+ ],+ "x_dir": [+ 1,+ 0,+ 0+ ],+ "y_dir": [+ 0,+ 0,+ 1+ ]+ },+ "name": "B"+ }+ },+ {+ "command": "sketch.rectangle.two_point",+ "params": {+ "p0": [+ 20.5,+ 4+ ],+ "p1": [+ 28,+ 18+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.revolve",+ "params": {+ "sketch": "B",+ "axis": "y",+ "body_name": "RingB"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "RingB",+ "tools": [+ "RingA"+ ],+ "operation": "join"+ }+ }+ ]+}diff --git a/tests/kernel-cases/crashes/skipped-4161.json b/tests/kernel-cases/crashes/skipped-4161.jsonindex 762e91b76a..c5e6296ddb 100644--- a/tests/kernel-cases/crashes/skipped-4161.json+++ b/tests/kernel-cases/crashes/skipped-4161.json@@ -78,5 +78,53 @@{"source": "tangency-labs/solidcraft#4422","why": "render: wgpu surface not configured, no geometry"+ },+ {+ "source": "tangency-labs/solidcraft#4469",+ "why": "the recipe needs sketch.offset of a free-form chain (PR #4156), refused on this branch before the kernel is reached; the two-distance chamfer of a spline rim is fillets/4332-two-distance-chamfer-of-spline-rim"+ },+ {+ "source": "tangency-labs/solidcraft#4476",+ "why": "no geometry: unclean exit in timeline.dependents (document), the design is not given"+ },+ {+ "source": "tangency-labs/solidcraft#4478",+ "why": "no reproduction: the display triangulation library's assertion, title only"+ },+ {+ "source": "tangency-labs/solidcraft#4491",+ "why": "render: blank or corrupted offscreen captures, no geometry"+ },+ {+ "source": "tangency-labs/solidcraft#4559",+ "why": "no geometry: unclean exit with no command running (an agent driving the app)"+ },+ {+ "source": "tangency-labs/solidcraft#4599",+ "why": "render: a GPU hang (Intel/Mesa); the replay rebuilds cleanly"+ },+ {+ "source": "tangency-labs/solidcraft#4604",+ "why": "no geometry: measuring a large assembly runs on the window thread (document/UI)"+ },+ {+ "source": "tangency-labs/solidcraft#4605",+ "why": "render: startup failure creating the graphics device on macOS"+ },+ {+ "source": "tangency-labs/solidcraft#4627",+ "why": "render: crash inside the NVIDIA driver, no command"+ },+ {+ "source": "tangency-labs/solidcraft#4709",+ "why": "no reproduction: a slow extrude shown by screenshot only"+ },+ {+ "source": "tangency-labs/solidcraft#4777",+ "why": "no geometry: unclean exit with no command and no replay"+ },+ {+ "source": "tangency-labs/solidcraft#4791",+ "why": "render: capture buffer and GPU hang on Intel/Mesa, no geometry"}]diff --git a/tests/kernel-cases/fillets/4702-chamfer-slot-wall-edge-on-outer-cylinder/expected.json b/tests/kernel-cases/fillets/4702-chamfer-slot-wall-edge-on-outer-cylinder/expected.jsonnew file mode 100644index 0000000000..c5d2318aa7--- /dev/null+++ b/tests/kernel-cases/fillets/4702-chamfer-slot-wall-edge-on-outer-cylinder/expected.json@@ -0,0 +1,14 @@+{+ "sources": [+ "tangency-labs/solidcraft#4702"+ ],+ "what": "a disc (r16 x 5) with a radial slot cut 3.2 down (65..115 deg, r 10 out through the rim): the vertical edge where a slot wall meets the outer cylinder chamfered 0.4: refused ('both faces next to the edge must be planar')",+ "source": "analytic",+ "method": "disc pi 256 5 less the slot sector (50/360) pi (16^2 - 10^2) 3.2. The chamfer cuts the corner between the radial wall and the cylinder: from 0.4 in along the wall to 0.4 round the cylinder, i.e. the triangle (corner, the two points) plus the circular segment r^2/2 (d - sin d), d = 0.4/16, over the 3.2 mm edge. Faces: top, bottom, outer cylinder, slot floor, two walls, inner wall, chamfer = 8. Graded to 1e-5 relative: the chamfer is 7e-5 of the volume, and how a distance is measured round the cylinder (along it, or to the offset surfaces' intersection) moves it by up to 4% of itself",+ "body_count": 1,+ "faces": 8,+ "volume_mm3": 3803.164466,+ "tolerance": {+ "rel": 1e-05+ }+}diff --git a/tests/kernel-cases/fillets/4702-chamfer-slot-wall-edge-on-outer-cylinder/recipe.json b/tests/kernel-cases/fillets/4702-chamfer-slot-wall-edge-on-outer-cylinder/recipe.jsonnew file mode 100644index 0000000000..0acda3f44b--- /dev/null+++ b/tests/kernel-cases/fillets/4702-chamfer-slot-wall-edge-on-outer-cylinder/recipe.json@@ -0,0 +1,119 @@+{+ "commands": [+ {+ "command": "solid.cylinder",+ "params": {+ "radius": 16,+ "height": 5,+ "body_name": "Adapter"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "face": [+ 0,+ 0,+ 5+ ]+ },+ "name": "Slot",+ "project_edges": false+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 4.226183,+ 9.063078+ ],+ [+ 8.452365,+ 18.126156+ ]+ ]+ }+ },+ {+ "command": "sketch.arc.three_point",+ "params": {+ "start": [+ 8.452365,+ 18.126156+ ],+ "through": [+ 0.0,+ 20.0+ ],+ "end": [+ -8.452365,+ 18.126156+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -8.452365,+ 18.126156+ ],+ [+ -4.226183,+ 9.063078+ ]+ ]+ }+ },+ {+ "command": "sketch.arc.three_point",+ "params": {+ "start": [+ -4.226183,+ 9.063078+ ],+ "through": [+ 0.0,+ 10.0+ ],+ "end": [+ 4.226183,+ 9.063078+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.extrude",+ "params": {+ "sketch": "Slot",+ "distance": 3.2,+ "direction": "negative",+ "operation": "cut",+ "targets": [+ "Adapter"+ ]+ }+ },+ {+ "command": "solid.chamfer",+ "params": {+ "edges": [+ [+ 6.761892,+ 14.500925,+ 3.4+ ]+ ],+ "distance": 0.4+ }+ }+ ]+}diff --git a/tests/kernel-cases/fillets/skipped-4161.json b/tests/kernel-cases/fillets/skipped-4161.jsonindex 7c6ec87728..f8193b5e09 100644--- a/tests/kernel-cases/fillets/skipped-4161.json+++ b/tests/kernel-cases/fillets/skipped-4161.json@@ -54,5 +54,97 @@{"source": "tangency-labs/solidcraft#4429","why": "needs the user design: a damper of joined extrudes with six chamfers; the failing chain is not reproducible from the report"+ },+ {+ "source": "tangency-labs/solidcraft#4444",+ "why": "no reproduction: a variable-radius fillet on an unknown part with curved faces, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4472",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4474",+ "why": "no geometry: a sketch fillet at a zero-length line (sketch command)"+ },+ {+ "source": "tangency-labs/solidcraft#4495",+ "why": "needs the user design: a drafted boss whose corner runs onto a 17 deg face; not reproducible from the screenshot"+ },+ {+ "source": "tangency-labs/solidcraft#4496",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4498",+ "why": "no geometry: distance-and-angle chamfer exists (UI question)"+ },+ {+ "source": "tangency-labs/solidcraft#4499",+ "why": "needs the user design: a battery caddy with 40 features; the 8-edge outline is not reproducible alone"+ },+ {+ "source": "tangency-labs/solidcraft#4518",+ "why": "no single right answer: a second concave fillet ending on an earlier one's round (how they meet is the method's choice)"+ },+ {+ "source": "tangency-labs/solidcraft#4543",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4550",+ "why": "no reproduction: one edge on an unknown large part, screenshot only"+ },+ {+ "source": "tangency-labs/solidcraft#4569",+ "why": "no reproduction: an unequal chamfer round a loop on an unknown part (a stated limit)"+ },+ {+ "source": "tangency-labs/solidcraft#4575",+ "why": "no geometry: the reporter withdrew it (chamfer preview works)"+ },+ {+ "source": "tangency-labs/solidcraft#4661",+ "why": "no reproduction: vertical-edge fillets meeting earlier top fillets on an unknown part, no message or design"+ },+ {+ "source": "tangency-labs/solidcraft#4681",+ "why": "no geometry: sketch fillet radius rejects an expression (sketch)"+ },+ {+ "source": "tangency-labs/solidcraft#4690",+ "why": "needs the user design: a 19-feature, 2-body mount; the two edges are not reproducible from the report"+ },+ {+ "source": "tangency-labs/solidcraft#4703",+ "why": "UI only: a hole edge counts as \"2 selected\" (a seam-split circle)"+ },+ {+ "source": "tangency-labs/solidcraft#4716",+ "why": "no reproduction: a 10 mm chamfer beside a circle cuts the far side too, unknown part (0.18.3), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4744",+ "why": "no reproduction: a curved 8-edge chain on an unknown part (0.18.4), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4772",+ "why": "needs the user design: a 26-feature handle (poignee.json) with a fillet along a curve; no small stand-in"+ },+ {+ "source": "tangency-labs/solidcraft#4782",+ "why": "no geometry: a fillet rolling over onto the next face (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4793",+ "why": "no reproduction: a 9 mm chamfer of one curved edge on an unknown part (0.18.4)"+ },+ {+ "source": "tangency-labs/solidcraft#4795",+ "why": "needs the user design: a hook of filleted extrudes; the refusal depends on one earlier distance (11+3 vs 12.7+3)"+ },+ {+ "source": "tangency-labs/solidcraft#4806",+ "why": "no reproduction: a 0.2 mm chamfer chain on an unknown part, no design"}]diff --git a/tests/kernel-cases/import/4438-step-whole-torus-round-trip/expected.json b/tests/kernel-cases/import/4438-step-whole-torus-round-trip/expected.jsonnew file mode 100644index 0000000000..e739fe7aa2--- /dev/null+++ b/tests/kernel-cases/import/4438-step-whole-torus-round-trip/expected.json@@ -0,0 +1,11 @@+{+ "sources": [+ "tangency-labs/solidcraft#4438"+ ],+ "what": "a whole torus (R 15, r 5) exported to STEP and read back: truck wrote it as two faces on one shared loop with no seam edges (V-E+F = 2), which other readers took as a sphere-like shell of volume 0",+ "source": "analytic",+ "method": "V = 2*pi^2*R*r^2 = 7402.203, A = 4*pi^2*R*r = 2960.881. The re-imported body is graded, not the exported one (the design holds only the import)",+ "body_count": 1,+ "volume_mm3": 7402.2033,+ "area_mm2": 2960.8813+}diff --git a/tests/kernel-cases/import/4438-step-whole-torus-round-trip/recipe.json b/tests/kernel-cases/import/4438-step-whole-torus-round-trip/recipe.jsonnew file mode 100644index 0000000000..c56486310b--- /dev/null+++ b/tests/kernel-cases/import/4438-step-whole-torus-round-trip/recipe.json@@ -0,0 +1,31 @@+{+ "commands": [+ {+ "command": "solid.torus",+ "params": {+ "major": 15,+ "minor": 5,+ "body_name": "Torus"+ }+ },+ {+ "command": "file.export",+ "params": {+ "path": "$OUT/kernel-case-4438.step",+ "format": "step"+ }+ },+ {+ "command": "file.new",+ "params": {+ "name": "Reimported"+ }+ },+ {+ "command": "file.insert_step",+ "params": {+ "path": "$OUT/kernel-case-4438.step"+ }+ }+ ]+}diff --git a/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/box-degenerate.stl b/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/box-degenerate.stlnew file mode 100644index 0000000000..367e6292c7--- /dev/null+++ b/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/box-degenerate.stl@@ -0,0 +1,93 @@+solid box_degenerate+ facet normal 0 0 -1+ outer loop+ vertex 0 0 0+ vertex 20 10 0+ vertex 20 0 0+ endloop+ endfacet+ facet normal 0 0 -1+ outer loop+ vertex 0 0 0+ vertex 0 10 0+ vertex 20 10 0+ endloop+ endfacet+ facet normal 0 0 1+ outer loop+ vertex 0 0 5+ vertex 20 0 5+ vertex 20 10 5+ endloop+ endfacet+ facet normal 0 0 1+ outer loop+ vertex 0 0 5+ vertex 20 10 5+ vertex 0 10 5+ endloop+ endfacet+ facet normal 0 -1 0+ outer loop+ vertex 0 0 0+ vertex 20 0 0+ vertex 20 0 5+ endloop+ endfacet+ facet normal 0 -1 0+ outer loop+ vertex 0 0 0+ vertex 20 0 5+ vertex 0 0 5+ endloop+ endfacet+ facet normal 1 0 0+ outer loop+ vertex 20 0 0+ vertex 20 10 0+ vertex 20 10 5+ endloop+ endfacet+ facet normal 1 0 0+ outer loop+ vertex 20 0 0+ vertex 20 10 5+ vertex 20 0 5+ endloop+ endfacet+ facet normal 0 1 0+ outer loop+ vertex 20 10 0+ vertex 0 10 0+ vertex 0 10 5+ endloop+ endfacet+ facet normal 0 1 0+ outer loop+ vertex 20 10 0+ vertex 0 10 5+ vertex 20 10 5+ endloop+ endfacet+ facet normal -1 0 0+ outer loop+ vertex 0 10 0+ vertex 0 0 0+ vertex 0 0 5+ endloop+ endfacet+ facet normal -1 0 0+ outer loop+ vertex 0 10 0+ vertex 0 0 5+ vertex 0 10 5+ endloop+ endfacet+ facet normal 0 0 0+ outer loop+ vertex 0 0 0+ vertex 10 0 0+ vertex 20 0 0+ endloop+ endfacet+endsolid box_degeneratediff --git a/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/expected.json b/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/expected.jsonnew file mode 100644index 0000000000..acce4788bc--- /dev/null+++ b/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/expected.json@@ -0,0 +1,11 @@+{+ "sources": [+ "tangency-labs/solidcraft#4561"+ ],+ "what": "Convert Mesh of a 20x10x5 box STL (12 triangles) with one extra zero-area triangle lying on an edge ((0,0,0) (10,0,0) (20,0,0)): refused with 'mesh conversion: degenerate triangle'",+ "source": "analytic",+ "method": "the zero-area triangle adds no surface; the mesh is the closed box, a constant-section prism, so it converts: V = 20*10*5 = 1000, 6 faces. The STL is written by hand (box-degenerate.stl, the triage's mesh)",+ "body_count": 1,+ "faces": 6,+ "volume_mm3": 1000.0+}diff --git a/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/recipe.json b/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/recipe.jsonnew file mode 100644index 0000000000..c949bebf4d--- /dev/null+++ b/tests/kernel-cases/import/4561-convert-box-mesh-with-a-zero-area-triangle/recipe.json@@ -0,0 +1,22 @@+{+ "commands": [+ {+ "command": "file.insert_mesh",+ "params": {+ "path": "$CASE/box-degenerate.stl"+ }+ },+ {+ "command": "component.activate",+ "params": {+ "component": "box-degenerate"+ }+ },+ {+ "command": "mesh.convert",+ "params": {+ "body": "box-degenerate"+ }+ }+ ]+}diff --git a/tests/kernel-cases/import/4598-step-moved-cross-bored-rod-round-trip/expected.json b/tests/kernel-cases/import/4598-step-moved-cross-bored-rod-round-trip/expected.jsonnew file mode 100644index 0000000000..76cbcea4b8--- /dev/null+++ b/tests/kernel-cases/import/4598-step-moved-cross-bored-rod-round-trip/expected.json@@ -0,0 +1,23 @@+{+ "sources": [+ "tangency-labs/solidcraft#4598"+ ],+ "what": "an O40 x 60 rod with a blind O8 cross bore from its side (x 10..25 at mid height), moved 100 mm, exported to STEP and read back: the body came in empty with no warning (truck's exported edges had 1399 control points)",+ "source": "analytic",+ "method": "the bore runs from the wall (x = sqrt(400 - y^2)) in to its flat end at x = 10: removed = Int_-4^4 2 sqrt(16-y^2) (sqrt(400-y^2) - 10) dy (python quadrature) = 497.6028. V = pi*20^2*60 - removed. Faces: top, bottom, side, bore wall, bore end = 5. Moved 100 in x: bbox x 80..120",+ "body_count": 1,+ "faces": 5,+ "volume_mm3": 74900.6209,+ "bbox": {+ "min": [+ 80.0,+ -20.0,+ 0.0+ ],+ "max": [+ 120.0,+ 20.0,+ 60.0+ ]+ }+}diff --git a/tests/kernel-cases/import/4598-step-moved-cross-bored-rod-round-trip/recipe.json b/tests/kernel-cases/import/4598-step-moved-cross-bored-rod-round-trip/recipe.jsonnew file mode 100644index 0000000000..8ffc67465c--- /dev/null+++ b/tests/kernel-cases/import/4598-step-moved-cross-bored-rod-round-trip/recipe.json@@ -0,0 +1,64 @@+{+ "commands": [+ {+ "command": "solid.cylinder",+ "params": {+ "diameter": 40,+ "height": 60,+ "body_name": "Rod"+ }+ },+ {+ "command": "solid.cylinder",+ "params": {+ "diameter": 8,+ "height": 15,+ "base": [+ 10,+ 0,+ 30+ ],+ "axis": "X",+ "operation": "cut",+ "targets": [+ "Rod"+ ]+ }+ },+ {+ "command": "solid.move",+ "params": {+ "bodies": [+ "Rod"+ ],+ "translate": [+ 100,+ 0,+ 0+ ]+ }+ },+ {+ "command": "file.export",+ "params": {+ "path": "$OUT/kernel-case-4598.step",+ "format": "step",+ "bodies": [+ "Rod"+ ]+ }+ },+ {+ "command": "file.new",+ "params": {+ "name": "Reimported"+ }+ },+ {+ "command": "file.insert_step",+ "params": {+ "path": "$OUT/kernel-case-4598.step"+ }+ }+ ]+}diff --git a/tests/kernel-cases/import/skipped-4161.json b/tests/kernel-cases/import/skipped-4161.jsonindex c9161a42be..e37cc35eb4 100644--- a/tests/kernel-cases/import/skipped-4161.json+++ b/tests/kernel-cases/import/skipped-4161.json@@ -6,5 +6,109 @@{"source": "tangency-labs/solidcraft#4274","why": "UI only: image canvas in sketches (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4451",+ "why": "no kernel geometry: OBJ export writes unshared vertices (file export)"+ },+ {+ "source": "tangency-labs/solidcraft#4483",+ "why": "no reproduction: operations on a user's 51-body STEP assembly (mostly working on 0.20.0)"+ },+ {+ "source": "tangency-labs/solidcraft#4485",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4500",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4552",+ "why": "no reproduction: a user's STEP wheels import with holes (the STEP is the reporter's)"+ },+ {+ "source": "tangency-labs/solidcraft#4553",+ "why": "no geometry: FreeCAD history import (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4554",+ "why": "no geometry: History hover stalls on large assemblies (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4560",+ "why": "no geometry: Convert Mesh's 50 000 triangle limit, as designed (dup of #346)"+ },+ {+ "source": "tangency-labs/solidcraft#4564",+ "why": "no geometry: Convert Mesh takes constant-section prisms only, as designed (dup of #358)"+ },+ {+ "source": "tangency-labs/solidcraft#4586",+ "why": "no geometry: Convert Mesh takes constant-section prisms only, as designed (dup of #358)"+ },+ {+ "source": "tangency-labs/solidcraft#4609",+ "why": "no geometry: Convert Mesh needs the mesh's component active (document)"+ },+ {+ "source": "tangency-labs/solidcraft#4616",+ "why": "no geometry: viewport memory for repeated placements (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4632",+ "why": "no geometry: Convert Mesh takes constant-section prisms only, as designed (dup of #358)"+ },+ {+ "source": "tangency-labs/solidcraft#4633",+ "why": "no geometry: Convert Mesh run without a mesh body selected (user error)"+ },+ {+ "source": "tangency-labs/solidcraft#4637",+ "why": "no geometry: viewport mesh indexing (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4646",+ "why": "no geometry: viewport culling of instanced placements (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4662",+ "why": "no geometry: mesh body size measured every frame (performance)"+ },+ {+ "source": "tangency-labs/solidcraft#4668",+ "why": "no geometry: hover highlight rebuilt per pointer move (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4673",+ "why": "no geometry: undo history copies imported meshes (memory)"+ },+ {+ "source": "tangency-labs/solidcraft#4676",+ "why": "no kernel geometry: Insert STEP ignores its matrix parameter (placement)"+ },+ {+ "source": "tangency-labs/solidcraft#4679",+ "why": "no geometry: welding a large mesh for display stalls a frame (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4700",+ "why": "no geometry: Convert Mesh takes constant-section prisms only, as designed (dup of #358)"+ },+ {+ "source": "tangency-labs/solidcraft#4722",+ "why": "no geometry: a freeform STL refused by Convert Mesh, as designed (dup of #358 and #4609)"+ },+ {+ "source": "tangency-labs/solidcraft#4724",+ "why": "no geometry: display levels of detail (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4768",+ "why": "no kernel geometry: moving repeated STEP placements moves the shared definition (placement)"+ },+ {+ "source": "tangency-labs/solidcraft#4814",+ "why": "no geometry: Convert Mesh needs the mesh's component active (dup of #4609)"}]diff --git a/tests/kernel-cases/sheet-metal/skipped-4161.json b/tests/kernel-cases/sheet-metal/skipped-4161.jsonindex 4dec330a23..971ca1b163 100644--- a/tests/kernel-cases/sheet-metal/skipped-4161.json+++ b/tests/kernel-cases/sheet-metal/skipped-4161.json@@ -14,5 +14,21 @@{"source": "tangency-labs/solidcraft#4301","why": "no geometry: Flange on a body that isn't sheet metal (dup of #2987)"+ },+ {+ "source": "tangency-labs/solidcraft#4440",+ "why": "UI only: the flat pattern view doesn't draw perforations"+ },+ {+ "source": "tangency-labs/solidcraft#4514",+ "why": "no geometry: Flange on a body that isn't sheet metal (dup of #2987)"+ },+ {+ "source": "tangency-labs/solidcraft#4713",+ "why": "no reproduction: Press Pull on a user's sheet-metal part runs a solid extrude (tool choice)"+ },+ {+ "source": "tangency-labs/solidcraft#4720",+ "why": "no geometry: two sheet-metal bodies combined lose their flat pattern, as warned (feature request)"}]diff --git a/tests/kernel-cases/shell/4492-offset-top-face-of-block-with-rounded-top-edges/expected.json b/tests/kernel-cases/shell/4492-offset-top-face-of-block-with-rounded-top-edges/expected.jsonnew file mode 100644index 0000000000..7e05fa4e64--- /dev/null+++ b/tests/kernel-cases/shell/4492-offset-top-face-of-block-with-rounded-top-edges/expected.json@@ -0,0 +1,9 @@+{+ "sources": [+ "tangency-labs/solidcraft#4492"+ ],+ "what": "the top face of a 40x30x10 block whose four top edges are rounded r3, offset 19 mm up: truck refused it ('a corner whose faces don't meet the same way after the move')",+ "source": "invariants",+ "method": "the top face's neighbours are the rounds, tangent to it, which cannot extend to meet a plane 19 mm higher; how the gap closes (the rounds carried up with the face, or walls standing on the old face) is the method's choice, so only the outcome is graded: the offset succeeds with one valid closed body",+ "body_count": 1+}diff --git a/tests/kernel-cases/shell/4492-offset-top-face-of-block-with-rounded-top-edges/recipe.json b/tests/kernel-cases/shell/4492-offset-top-face-of-block-with-rounded-top-edges/recipe.jsonnew file mode 100644index 0000000000..6a4fcc5825--- /dev/null+++ b/tests/kernel-cases/shell/4492-offset-top-face-of-block-with-rounded-top-edges/recipe.json@@ -0,0 +1,59 @@+{+ "commands": [+ {+ "command": "solid.box",+ "params": {+ "corner": [+ 0,+ 0,+ 0+ ],+ "length": 40,+ "width": 30,+ "height": 10,+ "body_name": "Block"+ }+ },+ {+ "command": "solid.fillet",+ "params": {+ "edges": [+ [+ 20,+ 0,+ 10+ ],+ [+ 20,+ 30,+ 10+ ],+ [+ 0,+ 15,+ 10+ ],+ [+ 40,+ 15,+ 10+ ]+ ],+ "radius": 3+ }+ },+ {+ "command": "solid.offset_face",+ "params": {+ "faces": [+ [+ 20,+ 15,+ 10+ ]+ ],+ "distance": 19+ }+ }+ ]+}diff --git a/tests/kernel-cases/shell/4567-shell-spline-revolved-vase/expected.json b/tests/kernel-cases/shell/4567-shell-spline-revolved-vase/expected.jsonnew file mode 100644index 0000000000..a0c8f5d8fb--- /dev/null+++ b/tests/kernel-cases/shell/4567-shell-spline-revolved-vase/expected.json@@ -0,0 +1,12 @@+{+ "sources": [+ "tangency-labs/solidcraft#4567",+ "tangency-labs/solidcraft#5076",+ "tangency-labs/solidcraft#5050",+ "tangency-labs/solidcraft#4743"+ ],+ "what": "a vase revolved from a fit-point spline wall, shelled 2 mm from its flat top: truck refused any free-form wall ('offset: only bodies with planes, cylinders, cones, spheres and tori')",+ "source": "invariants",+ "method": "the spline wall's curvature radius stays well above 2 mm, so the inward 2 mm offset exists: one valid closed body, open at the top. The offset of a spline surface has no closed-form volume, so only the outcome is graded (the reporter's 7-command repro; the removed face is the flat top at y = 46)",+ "body_count": 1+}diff --git a/tests/kernel-cases/shell/4567-shell-spline-revolved-vase/recipe.json b/tests/kernel-cases/shell/4567-shell-spline-revolved-vase/recipe.jsonnew file mode 100644index 0000000000..476b309612--- /dev/null+++ b/tests/kernel-cases/shell/4567-shell-spline-revolved-vase/recipe.json@@ -0,0 +1,99 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": "XY"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 0,+ 0+ ],+ [+ 14,+ 3+ ],+ [+ 22,+ 14+ ],+ [+ 22,+ 26+ ],+ [+ 14,+ 36+ ],+ [+ 6,+ 40+ ],+ [+ 6,+ 46+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 6,+ 46+ ],+ [+ 0,+ 46+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 0,+ 46+ ],+ [+ 0,+ 0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.revolve",+ "params": {+ "axis": "y",+ "angle": "360 deg"+ }+ },+ {+ "command": "solid.shell",+ "params": {+ "faces": [+ [+ 0,+ 46,+ 3+ ]+ ],+ "thickness": "2 mm"+ }+ }+ ]+}diff --git a/tests/kernel-cases/shell/4711-shell-block-with-hole-clipped-by-notch/expected.json b/tests/kernel-cases/shell/4711-shell-block-with-hole-clipped-by-notch/expected.jsonnew file mode 100644index 0000000000..b24bdcebb0--- /dev/null+++ b/tests/kernel-cases/shell/4711-shell-block-with-hole-clipped-by-notch/expected.json@@ -0,0 +1,10 @@+{+ "sources": [+ "tangency-labs/solidcraft#4711"+ ],+ "what": "a 2 mm shell, open at the bottom, of a 60x40x10 block whose r3 through hole breaks out into a 10x10 notch at its edge: truck took 75 s and failed ('boolean Cut: no result')",+ "source": "invariants",+ "method": "every wall has room for 2 mm (the thinnest, between the hole and the block's side, is 4 mm), so the shell exists: one valid closed body with one shell, open at the bottom. The cavity's corners at the hole's break-out follow the offset surfaces, so the volume is not closed-form (the reporter's script)",+ "body_count": 1,+ "shells": 1+}diff --git a/tests/kernel-cases/shell/4711-shell-block-with-hole-clipped-by-notch/recipe.json b/tests/kernel-cases/shell/4711-shell-block-with-hole-clipped-by-notch/recipe.jsonnew file mode 100644index 0000000000..48090ed9c1--- /dev/null+++ b/tests/kernel-cases/shell/4711-shell-block-with-hole-clipped-by-notch/recipe.json@@ -0,0 +1,52 @@+{+ "commands": [+ {+ "command": "solid.box",+ "params": {+ "length": 60,+ "width": 40,+ "height": 10+ }+ },+ {+ "command": "solid.cylinder",+ "params": {+ "radius": 3,+ "height": 20,+ "base": [+ 22.5,+ 7,+ -5+ ],+ "operation": "cut"+ }+ },+ {+ "command": "solid.box",+ "params": {+ "length": 10,+ "width": 10,+ "height": 20,+ "corner": [+ 25,+ -5,+ -5+ ],+ "operation": "cut"+ }+ },+ {+ "command": "solid.shell",+ "params": {+ "faces": [+ [+ 50,+ 30,+ 0+ ]+ ],+ "thickness": 2+ }+ }+ ]+}diff --git a/tests/kernel-cases/shell/skipped-4161.json b/tests/kernel-cases/shell/skipped-4161.jsonindex 724cf71019..9ca6533e72 100644--- a/tests/kernel-cases/shell/skipped-4161.json+++ b/tests/kernel-cases/shell/skipped-4161.json@@ -30,5 +30,61 @@{"source": "tangency-labs/solidcraft#4385","why": "UI only: sketch offset's second distance dimension"+ },+ {+ "source": "tangency-labs/solidcraft#4464",+ "why": "no geometry: sketch offset removes degrees of freedom (sketch solver)"+ },+ {+ "source": "tangency-labs/solidcraft#4467",+ "why": "no reproduction: shell removing six faces of a user's 4-feature part, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4484",+ "why": "duplicate of #4879: the thicken now builds; the cut into it is #4879's case"+ },+ {+ "source": "tangency-labs/solidcraft#4503",+ "why": "no reproduction: shell of a user's twisted swept slot (free-form, dup of #2432), screenshots only"+ },+ {+ "source": "tangency-labs/solidcraft#4510",+ "why": "no geometry: delete face in the surface workspace heals instead of opening (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4522",+ "why": "no geometry: the report arrived empty"+ },+ {+ "source": "tangency-labs/solidcraft#4555",+ "why": "no kernel geometry: a face given by a point resolves to the other body's coplanar face (engine face lookup)"+ },+ {+ "source": "tangency-labs/solidcraft#4573",+ "why": "no kernel geometry: \"select at least one face to remove\" on a picked face (dup of #4555, engine face lookup)"+ },+ {+ "source": "tangency-labs/solidcraft#4574",+ "why": "no reproduction: shell beside a tangent face of an unknown part, screenshot only"+ },+ {+ "source": "tangency-labs/solidcraft#4583",+ "why": "no geometry: sketch offset with unsolved constraints (sketch)"+ },+ {+ "source": "tangency-labs/solidcraft#4742",+ "why": "no reproduction: a 0.1 mm shell after a draft and fillets on an unknown part, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4743",+ "why": "duplicate of the free-form shell case from #4567 (a loft's walls instead of a revolve's)"+ },+ {+ "source": "tangency-labs/solidcraft#4775",+ "why": "no geometry: Offset Face run with no faces picked (user error)"+ },+ {+ "source": "tangency-labs/solidcraft#4822",+ "why": "no reproduction: a screenshot only"}]diff --git a/tests/kernel-cases/sources.json b/tests/kernel-cases/sources.jsonindex 929683a3df..3fd402bdcc 100644--- a/tests/kernel-cases/sources.json+++ b/tests/kernel-cases/sources.json@@ -1683,5 +1683,201 @@"4424": "issue, open","4428": "issue, open","4429": "issue, open",- "4431": "issue, open"+ "4431": "issue, open",+ "4433": "issue, closed",+ "4434": "issue, closed",+ "4435": "issue, closed",+ "4437": "issue, open",+ "4438": "issue, open",+ "4440": "issue, closed",+ "4443": "issue, open",+ "4444": "issue, open",+ "4448": "issue, open",+ "4451": "issue, open",+ "4454": "issue, open",+ "4458": "issue, open",+ "4464": "issue, closed",+ "4465": "issue, open",+ "4467": "issue, open",+ "4468": "issue, open",+ "4469": "issue, open",+ "4472": "issue, open",+ "4474": "issue, open",+ "4476": "issue, open",+ "4477": "issue, open",+ "4478": "issue, closed",+ "4481": "issue, open",+ "4483": "issue, open",+ "4484": "issue, open",+ "4485": "issue, open",+ "4488": "issue, open",+ "4489": "issue, open",+ "4491": "issue, open",+ "4492": "issue, open",+ "4494": "issue, open",+ "4495": "issue, open",+ "4496": "issue, open",+ "4498": "issue, open",+ "4499": "issue, open",+ "4500": "issue, open",+ "4502": "issue, open",+ "4503": "issue, open",+ "4505": "issue, open",+ "4506": "issue, closed",+ "4509": "issue, open",+ "4510": "issue, open",+ "4514": "issue, closed",+ "4516": "issue, open",+ "4518": "issue, open",+ "4521": "issue, open",+ "4522": "issue, open",+ "4523": "issue, open",+ "4524": "issue, open",+ "4525": "issue, open",+ "4528": "issue, open",+ "4530": "issue, open",+ "4532": "issue, open",+ "4534": "issue, closed",+ "4537": "issue, open",+ "4542": "issue, open",+ "4543": "issue, open",+ "4544": "issue, open",+ "4547": "issue, open",+ "4550": "issue, open",+ "4551": "issue, open",+ "4552": "issue, open",+ "4553": "issue, open",+ "4554": "issue, open",+ "4555": "issue, closed",+ "4557": "issue, open",+ "4558": "issue, closed",+ "4559": "issue, open",+ "4560": "issue, open",+ "4561": "issue, open",+ "4563": "issue, closed",+ "4564": "issue, closed",+ "4567": "issue, open",+ "4569": "issue, open",+ "4572": "issue, open",+ "4573": "issue, open",+ "4574": "issue, open",+ "4575": "issue, closed",+ "4576": "issue, closed",+ "4577": "issue, open",+ "4579": "issue, open",+ "4582": "issue, closed",+ "4583": "issue, open",+ "4584": "issue, open",+ "4586": "issue, open",+ "4589": "issue, closed",+ "4593": "issue, closed",+ "4594": "issue, open",+ "4597": "issue, open",+ "4598": "issue, open",+ "4599": "issue, closed",+ "4600": "issue, open",+ "4604": "issue, closed",+ "4605": "issue, open",+ "4606": "issue, open",+ "4609": "issue, closed",+ "4616": "issue, open",+ "4619": "issue, open",+ "4621": "issue, open",+ "4623": "issue, closed",+ "4624": "issue, open",+ "4627": "issue, open",+ "4631": "issue, open",+ "4632": "issue, open",+ "4633": "issue, open",+ "4636": "issue, open",+ "4637": "issue, open",+ "4639": "issue, open",+ "4643": "issue, open",+ "4644": "issue, open",+ "4646": "issue, closed",+ "4654": "issue, open",+ "4658": "issue, closed",+ "4661": "issue, open",+ "4662": "issue, closed",+ "4665": "issue, closed",+ "4668": "issue, closed",+ "4672": "issue, open",+ "4673": "issue, closed",+ "4676": "issue, closed",+ "4679": "issue, closed",+ "4681": "issue, closed",+ "4683": "issue, open",+ "4684": "issue, open",+ "4685": "issue, open",+ "4689": "issue, open",+ "4690": "issue, open",+ "4694": "issue, open",+ "4696": "issue, open",+ "4697": "issue, open",+ "4699": "issue, open",+ "4700": "issue, open",+ "4701": "issue, closed",+ "4702": "issue, open",+ "4703": "issue, open",+ "4704": "issue, open",+ "4706": "issue, open",+ "4708": "issue, open",+ "4709": "issue, open",+ "4711": "issue, open",+ "4713": "issue, open",+ "4714": "issue, open",+ "4715": "issue, open",+ "4716": "issue, open",+ "4720": "issue, open",+ "4722": "issue, closed",+ "4723": "issue, open",+ "4724": "issue, closed",+ "4726": "issue, open",+ "4727": "issue, open",+ "4728": "issue, open",+ "4729": "issue, open",+ "4730": "issue, open",+ "4731": "issue, open",+ "4733": "issue, open",+ "4734": "issue, closed",+ "4735": "issue, open",+ "4736": "issue, open",+ "4737": "issue, open",+ "4738": "issue, closed",+ "4741": "issue, closed",+ "4742": "issue, open",+ "4743": "issue, open",+ "4744": "issue, open",+ "4750": "issue, open",+ "4753": "issue, open",+ "4755": "issue, open",+ "4756": "issue, open",+ "4760": "issue, open",+ "4761": "issue, open",+ "4763": "issue, open",+ "4768": "issue, open",+ "4772": "issue, open",+ "4775": "issue, open",+ "4777": "issue, open",+ "4782": "issue, open",+ "4783": "issue, closed",+ "4791": "issue, open",+ "4793": "issue, open",+ "4795": "issue, open",+ "4798": "issue, open",+ "4799": "issue, open",+ "4800": "issue, closed",+ "4803": "issue, open",+ "4805": "issue, open",+ "4806": "issue, open",+ "4807": "issue, open",+ "4810": "issue, open",+ "4814": "issue, closed",+ "4818": "issue, open",+ "4822": "issue, open",+ "4825": "issue, closed",+ "4826": "issue, open",+ "4827": "issue, open",+ "4828": "issue, open",+ "4829": "issue, open"}diff --git a/tests/kernel-cases/sweeps/4683-cut-mirrored-loft-with-tilted-last-section/expected.json b/tests/kernel-cases/sweeps/4683-cut-mirrored-loft-with-tilted-last-section/expected.jsonnew file mode 100644index 0000000000..78f08b94b4--- /dev/null+++ b/tests/kernel-cases/sweeps/4683-cut-mirrored-loft-with-tilted-last-section/expected.json@@ -0,0 +1,9 @@+{+ "sources": [+ "tangency-labs/solidcraft#4683"+ ],+ "what": "a box cut from a 6-section loft (spline crown and a flat bottom at z = -1) whose last section lies on a plane tilted 2 deg off its neighbours', mirrored into one body; the box crosses the tilted end and reaches below the bottom face: truck's result shell was missing a face ('no result')",+ "source": "invariants",+ "method": "the mirrored loft is one solid symmetric about YZ, x -149..149; the box (x 91..240, y 90..210, z -2..118) cuts through its tilted end and out of its flat bottom, so the cut leaves one valid closed body. The loft's free-form volume is not closed-form. Synthetic sections of the report's shape (a crowned spline over a flat base, narrowing along x), not its numbers",+ "body_count": 1+}diff --git a/tests/kernel-cases/sweeps/4683-cut-mirrored-loft-with-tilted-last-section/recipe.json b/tests/kernel-cases/sweeps/4683-cut-mirrored-loft-with-tilted-last-section/recipe.jsonnew file mode 100644index 0000000000..2cf9fbbc40--- /dev/null+++ b/tests/kernel-cases/sweeps/4683-cut-mirrored-loft-with-tilted-last-section/recipe.json@@ -0,0 +1,584 @@+{+ "commands": [+ {+ "command": "construct.plane.offset",+ "params": {+ "base": "YZ",+ "offset": "0 mm",+ "name": "P0"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "P0",+ "name": "S0"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 300.0,+ 2.0+ ],+ [+ 225.0,+ 41.375+ ],+ [+ 150.0,+ 69.5+ ],+ [+ 75.0,+ 86.375+ ],+ [+ 0.0,+ 92.0+ ],+ [+ -75.0,+ 86.375+ ],+ [+ -150.0,+ 69.5+ ],+ [+ -225.0,+ 41.375+ ],+ [+ -300.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -300.0,+ 2.0+ ],+ [+ -303.0,+ -1+ ],+ [+ 303.0,+ -1+ ],+ [+ 300.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "construct.plane.offset",+ "params": {+ "base": "YZ",+ "offset": "30 mm",+ "name": "P30"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "P30",+ "name": "S30"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 282.0,+ 2.0+ ],+ [+ 211.5,+ 36.7812+ ],+ [+ 141.0,+ 61.625+ ],+ [+ 70.5,+ 76.5312+ ],+ [+ 0.0,+ 81.5+ ],+ [+ -70.5,+ 76.5312+ ],+ [+ -141.0,+ 61.625+ ],+ [+ -211.5,+ 36.7812+ ],+ [+ -282.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -282.0,+ 2.0+ ],+ [+ -285.0,+ -1+ ],+ [+ 285.0,+ -1+ ],+ [+ 282.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "construct.plane.offset",+ "params": {+ "base": "YZ",+ "offset": "60 mm",+ "name": "P60"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "P60",+ "name": "S60"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 264.0,+ 2.0+ ],+ [+ 198.0,+ 32.1875+ ],+ [+ 132.0,+ 53.75+ ],+ [+ 66.0,+ 66.6875+ ],+ [+ 0.0,+ 71.0+ ],+ [+ -66.0,+ 66.6875+ ],+ [+ -132.0,+ 53.75+ ],+ [+ -198.0,+ 32.1875+ ],+ [+ -264.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -264.0,+ 2.0+ ],+ [+ -267.0,+ -1+ ],+ [+ 267.0,+ -1+ ],+ [+ 264.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "construct.plane.offset",+ "params": {+ "base": "YZ",+ "offset": "100 mm",+ "name": "P100"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "P100",+ "name": "S100"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 240.0,+ 2.0+ ],+ [+ 180.0,+ 26.0625+ ],+ [+ 120.0,+ 43.25+ ],+ [+ 60.0,+ 53.5625+ ],+ [+ 0.0,+ 57.0+ ],+ [+ -60.0,+ 53.5625+ ],+ [+ -120.0,+ 43.25+ ],+ [+ -180.0,+ 26.0625+ ],+ [+ -240.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -240.0,+ 2.0+ ],+ [+ -243.0,+ -1+ ],+ [+ 243.0,+ -1+ ],+ [+ 240.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "construct.plane.offset",+ "params": {+ "base": "YZ",+ "offset": "130 mm",+ "name": "P130"+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": "P130",+ "name": "S130"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 222.0,+ 2.0+ ],+ [+ 166.5,+ 21.4688+ ],+ [+ 111.0,+ 35.375+ ],+ [+ 55.5,+ 43.7188+ ],+ [+ 0.0,+ 46.5+ ],+ [+ -55.5,+ 43.7188+ ],+ [+ -111.0,+ 35.375+ ],+ [+ -166.5,+ 21.4688+ ],+ [+ -222.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -222.0,+ 2.0+ ],+ [+ -225.0,+ -1+ ],+ [+ 225.0,+ -1+ ],+ [+ 222.0,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "origin": [+ 149.0,+ 0.0,+ 0.0+ ],+ "x_dir": [+ 0.0,+ 1.0,+ 0.0+ ],+ "y_dir": [+ -0.034899,+ 0.0,+ 0.999391+ ]+ },+ "name": "S149"+ }+ },+ {+ "command": "sketch.spline.fit_point",+ "params": {+ "points": [+ [+ 210.6,+ 2.0+ ],+ [+ 157.95,+ 18.5594+ ],+ [+ 105.3,+ 30.3875+ ],+ [+ 52.65,+ 37.4844+ ],+ [+ 0.0,+ 39.85+ ],+ [+ -52.65,+ 37.4844+ ],+ [+ -105.3,+ 30.3875+ ],+ [+ -157.95,+ 18.5594+ ],+ [+ -210.6,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ -210.6,+ 2.0+ ],+ [+ -213.6,+ -1+ ],+ [+ 213.6,+ -1+ ],+ [+ 210.6,+ 2.0+ ]+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.loft",+ "params": {+ "sections": [+ {+ "sketch": "S0"+ },+ {+ "sketch": "S30"+ },+ {+ "sketch": "S60"+ },+ {+ "sketch": "S100"+ },+ {+ "sketch": "S130"+ },+ {+ "sketch": "S149"+ }+ ],+ "body_name": "Top",+ "name": "Top"+ }+ },+ {+ "command": "solid.mirror",+ "params": {+ "bodies": [+ "Top"+ ],+ "plane": "YZ",+ "combine": true+ }+ },+ {+ "command": "solid.box",+ "params": {+ "length": 149,+ "width": 120,+ "height": 120,+ "center": [+ 165.5,+ 150.0,+ 58.0+ ],+ "operation": "new",+ "body_name": "K"+ }+ },+ {+ "command": "solid.combine",+ "params": {+ "target": "Top",+ "tools": [+ "K"+ ],+ "operation": "cut"+ }+ }+ ]+}diff --git a/tests/kernel-cases/sweeps/4689-revolve-profile-with-edge-on-axis-keeps-flat-faces-whole/expected.json b/tests/kernel-cases/sweeps/4689-revolve-profile-with-edge-on-axis-keeps-flat-faces-whole/expected.jsonnew file mode 100644index 0000000000..2281cc61f3--- /dev/null+++ b/tests/kernel-cases/sweeps/4689-revolve-profile-with-edge-on-axis-keeps-flat-faces-whole/expected.json@@ -0,0 +1,13 @@+{+ "sources": [+ "tangency-labs/solidcraft#4689",+ "tangency-labs/solidcraft#5317",+ "tangency-labs/solidcraft#4521"+ ],+ "what": "an L profile whose long leg lies on the revolve axis (the axis is the profile's own line), revolved 360 deg: the flat faces came out split into three 120 deg sectors",+ "source": "analytic",+ "method": "a disc r20 x 5 under a post r5 x 25: V = pi 400 5 + pi 25 25 = 8246.681. Faces: bottom, disc side, the ring on its top, post side, post top = 5 (each flat face one face)",+ "body_count": 1,+ "faces": 5,+ "volume_mm3": 8246.6807+}diff --git a/tests/kernel-cases/sweeps/4689-revolve-profile-with-edge-on-axis-keeps-flat-faces-whole/recipe.json b/tests/kernel-cases/sweeps/4689-revolve-profile-with-edge-on-axis-keeps-flat-faces-whole/recipe.jsonnew file mode 100644index 0000000000..c9c73af1f2--- /dev/null+++ b/tests/kernel-cases/sweeps/4689-revolve-profile-with-edge-on-axis-keeps-flat-faces-whole/recipe.json@@ -0,0 +1,71 @@+{+ "commands": [+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "origin": [+ 0,+ 0,+ 0+ ],+ "x_dir": [+ 1,+ 0,+ 0+ ],+ "y_dir": [+ 0,+ 0,+ 1+ ]+ },+ "name": "Profile"+ }+ },+ {+ "command": "sketch.line",+ "params": {+ "points": [+ [+ 0,+ 0+ ],+ [+ 20,+ 0+ ],+ [+ 20,+ 5+ ],+ [+ 5,+ 5+ ],+ [+ 5,+ 30+ ],+ [+ 0,+ 30+ ]+ ],+ "closed": true+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.revolve",+ "params": {+ "sketch": "Profile",+ "axis": "l6",+ "angle": "360 deg"+ }+ }+ ]+}diff --git a/tests/kernel-cases/sweeps/4708-revolve-cut-slot-through-shelled-cup-wall/expected.json b/tests/kernel-cases/sweeps/4708-revolve-cut-slot-through-shelled-cup-wall/expected.jsonnew file mode 100644index 0000000000..b48a16e396--- /dev/null+++ b/tests/kernel-cases/sweeps/4708-revolve-cut-slot-through-shelled-cup-wall/expected.json@@ -0,0 +1,10 @@+{+ "sources": [+ "tangency-labs/solidcraft#4708"+ ],+ "what": "a slot revolve-cut through the wall of a shelled cup (r 22.5, 2 mm walls) over 30 deg: the revolve cut (and the same cut as a combine) did nothing (synthetic: the report's cup also had a chamfer and a fillet)",+ "source": "analytic",+ "method": "cup pi 22.5^2 10 - pi 20.5^2 8; the slot's section (r 19..24, z 5..8) crosses the wall r 20.5..22.5: it removes (30/360) pi (22.5^2 - 20.5^2) 3",+ "body_count": 1,+ "volume_mm3": 5274.7341+}diff --git a/tests/kernel-cases/sweeps/4708-revolve-cut-slot-through-shelled-cup-wall/recipe.json b/tests/kernel-cases/sweeps/4708-revolve-cut-slot-through-shelled-cup-wall/recipe.jsonnew file mode 100644index 0000000000..8f2577da26--- /dev/null+++ b/tests/kernel-cases/sweeps/4708-revolve-cut-slot-through-shelled-cup-wall/recipe.json@@ -0,0 +1,78 @@+{+ "commands": [+ {+ "command": "solid.cylinder",+ "params": {+ "radius": 22.5,+ "height": 10,+ "body_name": "Cup"+ }+ },+ {+ "command": "solid.shell",+ "params": {+ "faces": [+ [+ 0,+ 0,+ 10+ ]+ ],+ "thickness": 2+ }+ },+ {+ "command": "sketch.create",+ "params": {+ "plane": {+ "origin": [+ 0,+ 0,+ 0+ ],+ "x_dir": [+ 1,+ 0,+ 0+ ],+ "y_dir": [+ 0,+ 0,+ 1+ ]+ },+ "name": "Slot",+ "project_edges": false+ }+ },+ {+ "command": "sketch.rectangle.two_point",+ "params": {+ "p0": [+ 19,+ 5+ ],+ "p1": [+ 24,+ 8+ ]+ }+ },+ {+ "command": "sketch.finish",+ "params": {}+ },+ {+ "command": "solid.revolve",+ "params": {+ "sketch": "Slot",+ "axis": "y",+ "angle": "30 deg",+ "operation": "cut",+ "targets": [+ "Cup"+ ]+ }+ }+ ]+}diff --git a/tests/kernel-cases/sweeps/skipped-4161.json b/tests/kernel-cases/sweeps/skipped-4161.jsonindex e896ee9745..07e6753a04 100644--- a/tests/kernel-cases/sweeps/skipped-4161.json+++ b/tests/kernel-cases/sweeps/skipped-4161.json@@ -18,5 +18,97 @@{"source": "tangency-labs/solidcraft#4358","why": "no kernel geometry: surface loft picks lost between copied sketches with the same curve ids (selection)"+ },+ {+ "source": "tangency-labs/solidcraft#4454",+ "why": "no geometry: a profile that crosses the revolve axis is refused by design (bisecting it at the axis works)"+ },+ {+ "source": "tangency-labs/solidcraft#4465",+ "why": "no kernel geometry: a surface pick kept by curve id resolves to the newest sketch (selection, dup of #4579)"+ },+ {+ "source": "tangency-labs/solidcraft#4506",+ "why": "no geometry: Revolve about a construction axis is not looked up (\"unknown sketch line\", command parameters)"+ },+ {+ "source": "tangency-labs/solidcraft#4521",+ "why": "duplicate of #4689: a profile edge on the revolve axis splits the flat faces"+ },+ {+ "source": "tangency-labs/solidcraft#4524",+ "why": "no reproduction: last command only (a loft join, 0.18.3), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4525",+ "why": "no kernel geometry: boundary surface picks a curve by id from the wrong place (selection)"+ },+ {+ "source": "tangency-labs/solidcraft#4528",+ "why": "no reproduction: a join of two user lofts, no message or design"+ },+ {+ "source": "tangency-labs/solidcraft#4576",+ "why": "no geometry: Revolve about a construction axis (dup of #4506)"+ },+ {+ "source": "tangency-labs/solidcraft#4579",+ "why": "no kernel geometry: surface loft picks by curve id resolve to the wrong sketch (selection; the loft itself builds)"+ },+ {+ "source": "tangency-labs/solidcraft#4606",+ "why": "needs the user design: a swept body of 594 faces (512 cones, 64 spheres) revolve-cut"+ },+ {+ "source": "tangency-labs/solidcraft#4631",+ "why": "duplicate of tessellation/466-revolved-cone-tip-stays-smooth: a cone revolved from a triangle drawn wrong at its tip"+ },+ {+ "source": "tangency-labs/solidcraft#4644",+ "why": "UI only: Fair and Match Surface open no dialog"+ },+ {+ "source": "tangency-labs/solidcraft#4694",+ "why": "no reproduction: last command only (a revolve join), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4696",+ "why": "no reproduction: a revolve join between cone and sphere faces of an unknown part, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4697",+ "why": "no reproduction: last command only (a revolve join), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4699",+ "why": "no reproduction: last command only (a revolve join), no design"+ },+ {+ "source": "tangency-labs/solidcraft#4704",+ "why": "no reproduction: a revolve join between cone and sphere faces of an unknown part, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4715",+ "why": "no single right answer: a railed loft's shape between sections follows the rails' fitted spline (3D sketch fitting)"+ },+ {+ "source": "tangency-labs/solidcraft#4729",+ "why": "no geometry: surface extrude has no To Object extent (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4730",+ "why": "no reproduction: a loft join hangs on a user's part, no design"+ },+ {+ "source": "tangency-labs/solidcraft#4737",+ "why": "no kernel geometry: surface extrude takes the newest sketch's curve of the same id (selection, dup of #4465)"+ },+ {+ "source": "tangency-labs/solidcraft#4738",+ "why": "no geometry: Revolve about a construction axis (dup of #4506)"+ },+ {+ "source": "tangency-labs/solidcraft#4828",+ "why": "needs the author's real duct part (STEP operands of a user design); a performance case"}]diff --git a/tests/kernel-cases/threads/4726-fine-pitch-m48x0.75-thread-25-mm/expected.json b/tests/kernel-cases/threads/4726-fine-pitch-m48x0.75-thread-25-mm/expected.jsonnew file mode 100644index 0000000000..ac10c94219--- /dev/null+++ b/tests/kernel-cases/threads/4726-fine-pitch-m48x0.75-thread-25-mm/expected.json@@ -0,0 +1,10 @@+{+ "sources": [+ "tangency-labs/solidcraft#4726"+ ],+ "what": "a modelled M48x0.75 thread over the whole 25 mm of a O48 bolt (33 turns): the browser build froze; coarse pitches and 4 mm of it worked, slowly",+ "source": "invariants",+ "method": "a modelled external thread on its own nominal shaft: one valid closed body within the case's timeout (slow by nature: 600 s); the helical faces have no closed-form volume",+ "body_count": 1,+ "timeout_s": 600+}diff --git a/tests/kernel-cases/threads/4726-fine-pitch-m48x0.75-thread-25-mm/recipe.json b/tests/kernel-cases/threads/4726-fine-pitch-m48x0.75-thread-25-mm/recipe.jsonnew file mode 100644index 0000000000..53ae79aac4--- /dev/null+++ b/tests/kernel-cases/threads/4726-fine-pitch-m48x0.75-thread-25-mm/recipe.json@@ -0,0 +1,25 @@+{+ "commands": [+ {+ "command": "solid.cylinder",+ "params": {+ "diameter": 48,+ "height": 25,+ "body_name": "Bolt"+ }+ },+ {+ "command": "solid.thread",+ "params": {+ "face": [+ 24,+ 0,+ 12.5+ ],+ "designation": "M48x0.75",+ "length": 25,+ "modeled": true+ }+ }+ ]+}diff --git a/tests/kernel-cases/threads/skipped-4161.json b/tests/kernel-cases/threads/skipped-4161.jsonindex f3b29538ae..dc82ef3239 100644--- a/tests/kernel-cases/threads/skipped-4161.json+++ b/tests/kernel-cases/threads/skipped-4161.json@@ -14,5 +14,49 @@{"source": "tangency-labs/solidcraft#4414","why": "no geometry: left-handed threads (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4494",+ "why": "duplicate of threads/3311-two-tapped-holes-both-modelled-threaded: a modelled thread re-faceting the body's other faces (a fillet here)"+ },+ {+ "source": "tangency-labs/solidcraft#4537",+ "why": "duplicate of threads/3311-two-tapped-holes-both-modelled-threaded: a second modelled thread on the same body finds no cylinder"+ },+ {+ "source": "tangency-labs/solidcraft#4577",+ "why": "no geometry: custom thread designations exist (M33.25x1.25 works)"+ },+ {+ "source": "tangency-labs/solidcraft#4665",+ "why": "no geometry: the GPU pick buffer (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4672",+ "why": "duplicate of threads/3311-two-tapped-holes-both-modelled-threaded: a modelled thread facets the other round faces; no sizes"+ },+ {+ "source": "tangency-labs/solidcraft#4684",+ "why": "no geometry: gear generator and offsettable threads (feature requests)"+ },+ {+ "source": "tangency-labs/solidcraft#4727",+ "why": "duplicate of threads/3311-two-tapped-holes-both-modelled-threaded: modelled threads are faceted; no sizes"+ },+ {+ "source": "tangency-labs/solidcraft#4734",+ "why": "no geometry: see-through bodies sorted per triangle (render)"+ },+ {+ "source": "tangency-labs/solidcraft#4735",+ "why": "no geometry: a tapered coil (feature request)"+ },+ {+ "source": "tangency-labs/solidcraft#4736",+ "why": "duplicate of threads/3311-two-tapped-holes-both-modelled-threaded: a modelled thread facets the body; no sizes"+ },+ {+ "source": "tangency-labs/solidcraft#4799",+ "why": "no geometry: cosmetic threads don't cut the model, by design"}]