Skip to content

SolidCraft: an open-source parametric 3D CAD application built in pure Rust. Desktop, web, and automation through MCP.

Wave 432/509: SMLib import: an extruded circle past a turn stays its exact spline

jyvikob9237538e435
diff --git a/crates/engine/src/tests.rs b/crates/engine/src/tests.rs
index 8d86118c1b..9cb46a158d 100644
--- a/crates/engine/src/tests.rs
+++ b/crates/engine/src/tests.rs
@@ -427,6 +427,72 @@ fn fillet_the_edges_between_two_overlapping_cylinders() {
assert!(rel(v, expect) < 2e-4, "{v} vs {expect}");
}
+/// A bar 40 long, 16 wide and 10 tall whose far end is a half disc of radius 8 about (40, 8),
+/// with a disc of radius 8 about the same centre sketched on its top (the top's outline
+/// projected) and extruded 10 up, joined: the bar's sides run tangent into the cylinder.
+/// V0 = 40·16·10 + π·8²·10/2 + π·8²·10.
+fn peg(s: &mut Session) -> f64 {
+ run(s, "sketch.create", json!({"plane": "XY", "name": "Peg"}));
+ run(s, "sketch.line", json!({"points": [[0, 0], [40, 0]]}));
+ run(s, "sketch.arc.center_point", json!({"center": [40, 8], "start": [40, 0], "end": [40, 16]}));
+ run(s, "sketch.line", json!({"points": [[40, 16], [0, 16]]}));
+ run(s, "sketch.line", json!({"points": [[0, 16], [0, 0]]}));
+ run(s, "sketch.finish", json!({}));
+ run(s, "solid.extrude", json!({"sketch": "Peg", "distance": 10, "body_name": "Peg"}));
+ run(s, "sketch.create", json!({"plane": {"origin": [0, 0, 10], "x_dir": [1, 0, 0], "y_dir": [0, 1, 0]}, "name": "Top"}));
+ run(s, "sketch.project", json!({"refs": [{"face": [2, 8, 10]}]}));
+ run(s, "sketch.circle.center", json!({"center": [40, 8], "radius": 8}));
+ run(s, "sketch.finish", json!({}));
+ run(
+ s,
+ "solid.extrude",
+ json!({"sketch": "Top", "distance": 10, "operation": "join", "targets": ["Peg"], "profiles": [{"point": [40, 8]}], "exact_regions": true}),
+ );
+ 6400.0 + 960.0 * PI
+}
+
+/// Simpson's rule over [a, b] with `n` (even) intervals.
+fn simpson(f: impl Fn(f64) -> f64, a: f64, b: f64, n: usize) -> f64 {
+ let h = (b - a) / n as f64;
+ let inner: f64 = (1..n).map(|i| if i % 2 == 1 { 4.0 } else { 2.0 } * f(a + h * i as f64)).sum();
+ (f(a) + f(b) + inner) * h / 3.0
+}
+
+/// The material an r2 round of the peg's front top edge (y = 0, z = 10) takes off: the spandrel
+/// (height 2 - sqrt(4 - (2 - y)²) above the round at y) from x = `from` to where the cylinder's
+/// wall, x = 40 - sqrt(64 - (8 - y)²), takes over (the round runs into the wall there).
+fn peg_front_round(from: f64) -> f64 {
+ let spandrel = |y: f64| 2.0 - (4.0 - (2.0 - y) * (2.0 - y)).max(0.0).sqrt();
+ let wall = |y: f64| 40.0 - (64.0 - (8.0 - y) * (8.0 - y)).max(0.0).sqrt();
+ simpson(|y| spandrel(y) * (wall(y) - from), 0.0, 2.0, 20_000)
+}
+
+/// The peg's front top edge rounded r2: SMLib's result holds the cylinder's wall as a rational
+/// spline whose parameter range runs more than a turn round. As a cylinder over that range (past
+/// 360°) SMLib refused it on the way back (SM_ERR_INVALID_INPUT), so the round seemed to build
+/// and the body could not be measured or changed. It stays the spline: the body measures, and a
+/// round of the three edges at the bar's other top corner builds on it.
+#[test]
+fn rounds_on_a_bar_running_tangent_into_a_cylinder() {
+ let mut s = Session::default();
+ let v0 = peg(&mut s);
+ run(&mut s, "solid.fillet", json!({"edges": [[20, 0, 10]], "radius": 2}));
+ let (v, expect) = (volume(&mut s), v0 - peg_front_round(0.0));
+ assert!(rel(v, expect) < 1e-7, "{v} vs {expect}");
+ // The vertical edge, the left top edge and the round's end arc on the left face: each
+ // spandrel (1 - π/4)·r² along the edge outside the corner cube of side 2, the cube less the
+ // rolling ball's eighth, 8 - 4π/3.
+ run(&mut s, "solid.fillet", json!({"edges": [[0, 0, 4], [0, 9, 10], [0, 0.5858, 9.4142]], "radius": 2}));
+ let strip = (1.0 - PI / 4.0) * 4.0;
+ let expect = v0 - peg_front_round(2.0) - strip * (8.0 + 14.0) - (8.0 - 4.0 * PI / 3.0);
+ let v = volume(&mut s);
+ assert!(rel(v, expect) < 1e-7, "{v} vs {expect}");
+ for b in &s.model.state().bodies {
+ let bad = b.body.validity();
+ assert!(bad.is_empty(), "{}: {bad:?}", b.name);
+ }
+}
+
/// The top outline of two overlapping cylinders whose concave edges were rounded: the walls of
/// the rounds meet the cylinders along the rolling-ball contact lines, straight but not lines.
#[test]
diff --git a/crates/smlib/src/import/analytic.rs b/crates/smlib/src/import/analytic.rs
index edf87e2193..f4735e4ef3 100644
--- a/crates/smlib/src/import/analytic.rs
+++ b/crates/smlib/src/import/analytic.rs
@@ -76,7 +76,7 @@ pub(super) fn analytic(brep: &b::Brep) -> R<Cow<'_, b::Brep>> {
/// A rational spline that is a circular arc swept straight along the arc's axis, as a cylinder
/// with the face's range on it: one direction linear (two rows of control points), the second
/// row the first moved by one vector at right angles to the circle the first row runs on, the
-/// weights alike. `None` where it is not.
+/// weights alike. `None` where it is not, or where its range runs more than one turn round.
fn extruded_circle(u_knots: &[f64], v_knots: &[f64], net: &[Vec<[f64; 4]>], domain: [[f64; 2]; 2], tol: f64) -> Option<(b::Surface, [[f64; 2]; 2])> {
let linear = |k: &[f64]| k.len() == 4 && k[0] == k[1] && k[2] == k[3] && k[1] < k[2];
let (rows, arc_knots, arc_range, line_knots, line_range): ([Vec<[f64; 4]>; 2], &[f64], [f64; 2], &[f64], [f64; 2]) =
@@ -117,6 +117,12 @@ fn extruded_circle(u_knots: &[f64], v_knots: &[f64], net: &[Vec<[f64; 4]>], doma
prev = a;
angle = a;
}
+ // A cylinder's range is at most one turn (SMLib refuses more). A spline whose range runs
+ // further round (SMLib's own, its parameter range past the face's trims) has no such range:
+ // it stays the exact spline it is.
+ if angle.abs() > TAU * (1.0 + 1e-9) {
+ return None;
+ }
let height = |s: f64| (s - line_knots[1]) / (line_knots[2] - line_knots[1]) * d.len();
let sorted = |a: f64, b: f64| if a <= b { [a, b] } else { [b, a] };
let frame = b::Frame { origin: arr(center), x_axis: arr(x), y_axis: arr(y) };
diff --git a/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-running-tangent-into-cylinder/expected.json b/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-running-tangent-into-cylinder/expected.json
new file mode 100644
index 0000000000..c37fb0587c
--- /dev/null
+++ b/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-running-tangent-into-cylinder/expected.json
@@ -0,0 +1,11 @@
+{
+ "sources": [
+ "tangency-labs/solidcraft#1207"
+ ],
+ "what": "an r2 round of a bar's top edge whose side runs tangent into a cylinder: the round seemed to build but its body could not be measured or changed (SMLib refused the cylinder's wall coming back as a cylinder over more than a turn)",
+ "source": "analytic",
+ "method": "a bar 40 x 16 x 10 whose far end is a half disc R8 about (40, 8), a disc R8 about the same centre sketched on its top (the top's outline projected) and extruded 10 up, joined: the bar's sides run tangent into the cylinder, V0 = 6400 + 960 pi; the r2 round of the front top edge (y = 0, z = 10) runs into the cylinder's wall: removed = integral over y in [0, 2] of (2 - sqrt(4 - (2 - y)^2)) (40 - sqrt(64 - (8 - y)^2)) dy = 32.3064821881 (Simpson)",
+ "body_count": 1,
+ "faces": 9,
+ "volume_mm3": 9383.622465258068
+}
diff --git a/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-running-tangent-into-cylinder/recipe.json b/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-running-tangent-into-cylinder/recipe.json
new file mode 100644
index 0000000000..5b1ff79bde
--- /dev/null
+++ b/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-running-tangent-into-cylinder/recipe.json
@@ -0,0 +1,169 @@
+{
+ "commands": [
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": "XY",
+ "name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0,
+ 0
+ ],
+ [
+ 40,
+ 0
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.arc.center_point",
+ "params": {
+ "center": [
+ 40,
+ 8
+ ],
+ "start": [
+ 40,
+ 0
+ ],
+ "end": [
+ 40,
+ 16
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 40,
+ 16
+ ],
+ [
+ 0,
+ 16
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0,
+ 16
+ ],
+ [
+ 0,
+ 0
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Peg",
+ "distance": 10,
+ "body_name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": {
+ "origin": [
+ 0,
+ 0,
+ 10
+ ],
+ "x_dir": [
+ 1,
+ 0,
+ 0
+ ],
+ "y_dir": [
+ 0,
+ 1,
+ 0
+ ]
+ },
+ "name": "Top"
+ }
+ },
+ {
+ "command": "sketch.project",
+ "params": {
+ "refs": [
+ {
+ "face": [
+ 2,
+ 8,
+ 10
+ ]
+ }
+ ]
+ }
+ },
+ {
+ "command": "sketch.circle.center",
+ "params": {
+ "center": [
+ 40,
+ 8
+ ],
+ "radius": 8
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Top",
+ "distance": 10,
+ "operation": "join",
+ "targets": [
+ "Peg"
+ ],
+ "profiles": [
+ {
+ "point": [
+ 40,
+ 8
+ ]
+ }
+ ],
+ "exact_regions": true
+ }
+ },
+ {
+ "command": "solid.fillet",
+ "params": {
+ "edges": [
+ [
+ 20,
+ 0,
+ 10
+ ]
+ ],
+ "radius": 2
+ }
+ }
+ ]
+}
diff --git a/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder-solver-residues/expected.json b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder-solver-residues/expected.json
new file mode 100644
index 0000000000..1ecfd0f084
--- /dev/null
+++ b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder-solver-residues/expected.json
@@ -0,0 +1,11 @@
+{
+ "sources": [
+ "tangency-labs/solidcraft#1207"
+ ],
+ "what": "as 1207-fillet-corner-after-round-running-into-cylinder, with the sketch solver's residues of the reported design",
+ "source": "analytic",
+ "method": "the same bar with the sketch solver's residues of the reported design (~1e-10 mm: the front side's ends differ by 3.0e-10 in y, the arc's centre 5.7e-11 off the disc's), length 41.160417754, V0 = 41.160417754 * 16.0000000000762 * 10 + 960 pi; the three r2 rounds at the bar's other top corner (0, 0, 10): the front round's spandrel from x = 2 to the wall (30.5896671706), the vertical edge's and the left top edge's (1 - pi/4) r^2 over 8 and 14, the corner cube of side 2 less the rolling ball's eighth, 8 - 4 pi/3: removed 53.2858385868; the bar being L = 41.160417754 long, the front round runs (L - 40) further: removed + (L - 40)(1 - pi/4) r^2",
+ "body_count": 1,
+ "faces": 12,
+ "volume_mm3": 9547.313838420392
+}
diff --git a/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder-solver-residues/recipe.json b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder-solver-residues/recipe.json
new file mode 100644
index 0000000000..fd1dbbc715
--- /dev/null
+++ b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder-solver-residues/recipe.json
@@ -0,0 +1,192 @@
+{
+ "commands": [
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": "XY",
+ "name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0.4892940775280783,
+ 0.05792545052986289
+ ],
+ [
+ 41.64971183161969,
+ 0.05792545083296555
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.arc.center_point",
+ "params": {
+ "center": [
+ 41.64971183108453,
+ 8.057925450890195
+ ],
+ "start": [
+ 41.64971183161969,
+ 0.05792545083296555
+ ],
+ "end": [
+ 41.64971183161969,
+ 16.05792545083297
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 41.64971183161969,
+ 16.05792545083297
+ ],
+ [
+ 0.4892940775280783,
+ 16.057925450606035
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0.4892940775280783,
+ 16.057925450606035
+ ],
+ [
+ 0.4892940775280783,
+ 0.05792545052986289
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Peg",
+ "distance": 10,
+ "body_name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": {
+ "origin": [
+ 0,
+ 0,
+ 10
+ ],
+ "x_dir": [
+ 1,
+ 0,
+ 0
+ ],
+ "y_dir": [
+ 0,
+ 1,
+ 0
+ ]
+ },
+ "name": "Top"
+ }
+ },
+ {
+ "command": "sketch.project",
+ "params": {
+ "refs": [
+ {
+ "face": [
+ 2.4892940775280783,
+ 8.057925450890195,
+ 10
+ ]
+ }
+ ]
+ }
+ },
+ {
+ "command": "sketch.circle.center",
+ "params": {
+ "center": [
+ 41.64971183108453,
+ 8.057925450832967
+ ],
+ "radius": 8.000000000006473
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Top",
+ "distance": 10,
+ "operation": "join",
+ "targets": [
+ "Peg"
+ ],
+ "profiles": [
+ {
+ "point": [
+ 41.64971183108453,
+ 8.057925450832967
+ ]
+ }
+ ],
+ "exact_regions": true
+ }
+ },
+ {
+ "command": "solid.fillet",
+ "params": {
+ "edges": [
+ [
+ 21.53,
+ 0.0579,
+ 10
+ ]
+ ],
+ "radius": 2
+ }
+ },
+ {
+ "command": "solid.fillet",
+ "params": {
+ "edges": [
+ [
+ 0.4893,
+ 0.0579,
+ 4
+ ],
+ [
+ 0.4893,
+ 9.058,
+ 10
+ ],
+ [
+ 0.4893,
+ 0.6437,
+ 9.4142
+ ]
+ ],
+ "radius": 2
+ }
+ }
+ ]
+}
diff --git a/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder/expected.json b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder/expected.json
new file mode 100644
index 0000000000..2924e30d38
--- /dev/null
+++ b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder/expected.json
@@ -0,0 +1,11 @@
+{
+ "sources": [
+ "tangency-labs/solidcraft#1207"
+ ],
+ "what": "after the round of a bar's top edge running into a cylinder, r2 rounds of the three edges at the bar's other top corner (the vertical edge, the left top edge and the round's end arc): 'one of its freeform faces can't be used'",
+ "source": "analytic",
+ "method": "a bar 40 x 16 x 10 whose far end is a half disc R8 about (40, 8), a disc R8 about the same centre sketched on its top (the top's outline projected) and extruded 10 up, joined: the bar's sides run tangent into the cylinder, V0 = 6400 + 960 pi; the three r2 rounds at the bar's other top corner (0, 0, 10): the front round's spandrel from x = 2 to the wall (30.5896671706), the vertical edge's and the left top edge's (1 - pi/4) r^2 over 8 and 14, the corner cube of side 2 less the rolling ball's eighth, 8 - 4 pi/3: removed 53.2858385868",
+ "body_count": 1,
+ "faces": 12,
+ "volume_mm3": 9362.643108859389
+}
diff --git a/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder/recipe.json b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder/recipe.json
new file mode 100644
index 0000000000..bc4f5fea2e
--- /dev/null
+++ b/tests/kernel-cases/fillets/1207-fillet-corner-after-round-running-into-cylinder/recipe.json
@@ -0,0 +1,192 @@
+{
+ "commands": [
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": "XY",
+ "name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0,
+ 0
+ ],
+ [
+ 40,
+ 0
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.arc.center_point",
+ "params": {
+ "center": [
+ 40,
+ 8
+ ],
+ "start": [
+ 40,
+ 0
+ ],
+ "end": [
+ 40,
+ 16
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 40,
+ 16
+ ],
+ [
+ 0,
+ 16
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0,
+ 16
+ ],
+ [
+ 0,
+ 0
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Peg",
+ "distance": 10,
+ "body_name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": {
+ "origin": [
+ 0,
+ 0,
+ 10
+ ],
+ "x_dir": [
+ 1,
+ 0,
+ 0
+ ],
+ "y_dir": [
+ 0,
+ 1,
+ 0
+ ]
+ },
+ "name": "Top"
+ }
+ },
+ {
+ "command": "sketch.project",
+ "params": {
+ "refs": [
+ {
+ "face": [
+ 2,
+ 8,
+ 10
+ ]
+ }
+ ]
+ }
+ },
+ {
+ "command": "sketch.circle.center",
+ "params": {
+ "center": [
+ 40,
+ 8
+ ],
+ "radius": 8
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Top",
+ "distance": 10,
+ "operation": "join",
+ "targets": [
+ "Peg"
+ ],
+ "profiles": [
+ {
+ "point": [
+ 40,
+ 8
+ ]
+ }
+ ],
+ "exact_regions": true
+ }
+ },
+ {
+ "command": "solid.fillet",
+ "params": {
+ "edges": [
+ [
+ 20,
+ 0,
+ 10
+ ]
+ ],
+ "radius": 2
+ }
+ },
+ {
+ "command": "solid.fillet",
+ "params": {
+ "edges": [
+ [
+ 0,
+ 0,
+ 4
+ ],
+ [
+ 0,
+ 9,
+ 10
+ ],
+ [
+ 0,
+ 0.5858,
+ 9.4142
+ ]
+ ],
+ "radius": 2
+ }
+ }
+ ]
+}
diff --git a/tests/kernel-cases/fillets/9-fillet-g2-corner-of-bar-running-into-cylinder/expected.json b/tests/kernel-cases/fillets/9-fillet-g2-corner-of-bar-running-into-cylinder/expected.json
new file mode 100644
index 0000000000..1d01a48246
--- /dev/null
+++ b/tests/kernel-cases/fillets/9-fillet-g2-corner-of-bar-running-into-cylinder/expected.json
@@ -0,0 +1,14 @@
+{
+ "sources": [
+ "tangency-labs/solidcraft#9"
+ ],
+ "what": "three r2 rounds at a top corner of a bar whose far end runs tangent into a cylinder, with the curvature (g2) corner set back 3: SMLib refused the result coming back (a cylinder over more than a turn)",
+ "source": "analytic",
+ "method": "a bar 40 x 16 x 10 whose far end is a half disc R8 about (40, 8), a disc R8 about the same centre sketched on its top (the top's outline projected) and extruded 10 up, joined: the bar's sides run tangent into the cylinder, V0 = 6400 + 960 pi; the rolling-ball answer: the three r2 rounds at the bar's other top corner (0, 0, 10): the front round's spandrel from x = 2 to the wall (30.5896671706), the vertical edge's and the left top edge's (1 - pi/4) r^2 over 8 and 14, the corner cube of side 2 less the rolling ball's eighth, 8 - 4 pi/3: removed 53.2858385868; the G2 patch differs from the ball only within the setback cube of side 3 about the vertex, so V is graded as V0 - removed with 3^3 as its tolerance",
+ "body_count": 1,
+ "faces": 12,
+ "volume_mm3": 9362.643108859389,
+ "tolerance": {
+ "rel": 0.002883801046998287
+ }
+}
diff --git a/tests/kernel-cases/fillets/9-fillet-g2-corner-of-bar-running-into-cylinder/recipe.json b/tests/kernel-cases/fillets/9-fillet-g2-corner-of-bar-running-into-cylinder/recipe.json
new file mode 100644
index 0000000000..e46fb10aff
--- /dev/null
+++ b/tests/kernel-cases/fillets/9-fillet-g2-corner-of-bar-running-into-cylinder/recipe.json
@@ -0,0 +1,191 @@
+{
+ "commands": [
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": "XY",
+ "name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0,
+ 0
+ ],
+ [
+ 40,
+ 0
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.arc.center_point",
+ "params": {
+ "center": [
+ 40,
+ 8
+ ],
+ "start": [
+ 40,
+ 0
+ ],
+ "end": [
+ 40,
+ 16
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 40,
+ 16
+ ],
+ [
+ 0,
+ 16
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.line",
+ "params": {
+ "points": [
+ [
+ 0,
+ 16
+ ],
+ [
+ 0,
+ 0
+ ]
+ ]
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Peg",
+ "distance": 10,
+ "body_name": "Peg"
+ }
+ },
+ {
+ "command": "sketch.create",
+ "params": {
+ "plane": {
+ "origin": [
+ 0,
+ 0,
+ 10
+ ],
+ "x_dir": [
+ 1,
+ 0,
+ 0
+ ],
+ "y_dir": [
+ 0,
+ 1,
+ 0
+ ]
+ },
+ "name": "Top"
+ }
+ },
+ {
+ "command": "sketch.project",
+ "params": {
+ "refs": [
+ {
+ "face": [
+ 2,
+ 8,
+ 10
+ ]
+ }
+ ]
+ }
+ },
+ {
+ "command": "sketch.circle.center",
+ "params": {
+ "center": [
+ 40,
+ 8
+ ],
+ "radius": 8
+ }
+ },
+ {
+ "command": "sketch.finish",
+ "params": {}
+ },
+ {
+ "command": "solid.extrude",
+ "params": {
+ "sketch": "Top",
+ "distance": 10,
+ "operation": "join",
+ "targets": [
+ "Peg"
+ ],
+ "profiles": [
+ {
+ "point": [
+ 40,
+ 8
+ ]
+ }
+ ],
+ "exact_regions": true
+ }
+ },
+ {
+ "command": "solid.fillet",
+ "params": {
+ "edges": [
+ [
+ 0,
+ 0,
+ 4
+ ],
+ [
+ 20,
+ 0,
+ 10
+ ],
+ [
+ 0,
+ 8,
+ 10
+ ]
+ ],
+ "radius": 2,
+ "corner": "g2",
+ "setbacks": [
+ {
+ "vertex": [
+ 0,
+ 0,
+ 10
+ ],
+ "distance": 3
+ }
+ ],
+ "tangent_chain": false
+ }
+ }
+ ]
+}
diff --git a/tests/kernel-cases/fillets/KNOWN_FAILING b/tests/kernel-cases/fillets/KNOWN_FAILING
index c86d34c84e..dadf33eb4f 100644
--- a/tests/kernel-cases/fillets/KNOWN_FAILING
+++ b/tests/kernel-cases/fillets/KNOWN_FAILING
@@ -21,6 +21,7 @@
2893-chamfer-distance-and-angle-past-the-wall-refused refused for another reason: SMLib SM_ERR_INVALID_INPUT, not a check saying the angle runs past the wall
2893-chamfer-two-distances-elliptical-rim SMLib status 1001 on the elliptical rim's chamfer
2893-chamfer-two-distances-past-the-bottom-refused refused for another reason: SMLib status 1001, not too large
+1207-fillet-corner-after-round-running-into-cylinder-solver-residues SMLib's check refuses the round: its corner's surface of revolution is close to singular at its boundary (SmSurface test 5)
4782-fillet-bar-edge-wider-than-both-faces SMLib status 1001: a convex round past both its faces is not yet built by subtraction
5158-fillet-round-just-past-a-10mm-face SMLib status 1001: a convex round 0.01 past its face is not yet built by subtraction (10.0001-10.04 open)
5835-chamfer-sloped-basin-1-mm-rim-0-5-4-edges SMLib status 1001 on the chamfers meeting at the rim's re-entrant corners