Interactive interface for browsing global, full-resolution satellite imagery
WV-3203: Add 2 TEMPO L3 O3 profile STD layers (#6174)
minniewongd5e211162df0
diff --git a/config/default/common/config/metadata/layers/tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule.md b/config/default/common/config/metadata/layers/tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule.mdnew file mode 100644index 000000000..08cec91ee--- /dev/null+++ b/config/default/common/config/metadata/layers/tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule.md@@ -0,0 +1,6 @@+The Tropospheric Emissions: Monitoring of Pollution (TEMPO) Total Ozone Column Amount layer provides information on the total amount of ozone in a vertical column of the atmosphere. The retrieval is performed using the Smithsonian Astrophysical Observatory (SAO) ozone profile algorithm, which is based on the optimal estimation method. The total ozone column is calculated by integrating the ozone profile provided in 24 vertical layers.++Imagery is available as approximately six-minute granules for daylight hours over North America. The sensor’s native spatial resolution is ~2 km x 4.75 km at the center of TEMPO’s field of regard (FOR). Due to the computational burden of on-line radiative transfer calculations and limited computational resources, a spatial coadding strategy is applied. Specifically, four native ground pixels in the North-South direction are coadded and provided as a single retrieval pixel. Therefore, the product’s spatial resolution is ~8 km x 4.75 km at the center of TEMPO’s FOR, and the imagery resolution is 2 km. The layer is filtered to remove low-quality pixels based on several criteria, using retrieval exit status (removing data that are not converged), solar zenith angle (removing data retrieved at high solar zenith angles), viewing zenith angle (removing data retrieved at high viewing zenith angles), fit RMS (removing with a high ratio of fitting residual to measurement error), average residual (removing data with high average relative fitting residual) and effective cloud fraction (removing where clouds obscure the column) variables. The filters applied are set to remove pixels based on the following: retrieval exit status ≤ 1 and ≥ 99, solar zenith angle greater than 80 degrees, viewing zenith angle greater than 80 degrees, fit RMS greater than 3, average residual greater than 0.3, and effective cloud fraction greater than 0.5.++Ozone profile Level 2 files provide ozone (ozone profile, total ozone column, troposphere ozone column, and stratosphere ozone column) and supporting information at spatial resolution of four North-South direction coadded from TEMPO’s native spatial resolution for individual granules. Each granule covers the entire North-South TEMPO FOR but only a portion of the East-West FOR. The temporal resolution of a nominal scan is approximately one hour during daylight hours, with more frequent scans in the morning over the eastern portion of the FOR and in the evenings over the western portion of the FOR.+diff --git a/config/default/common/config/metadata/layers/tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.md b/config/default/common/config/metadata/layers/tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.mdnew file mode 100644index 000000000..f271bfb9f--- /dev/null+++ b/config/default/common/config/metadata/layers/tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.md@@ -0,0 +1,5 @@+The Tropospheric Emissions: Monitoring of Pollution (TEMPO) Troposphere Ozone Column Amount layer provides information on the total amount of ozone in a vertical column of the troposphere. The retrieval is performed using the Smithsonian Astrophysical Observatory (SAO) ozone profile algorithm, which is based on the optimal estimation method. The troposphere ozone column was calculated by integrating the ozone profile from surface to the tropopause, using tropopause information from the Goddard Earth Observing System Composition Forecast (GEOS-CF) data.++Imagery is available as approximately six-minute granules for daylight hours over North America. The sensor’s native spatial resolution is ~2 km x 4.75 km at the center of TEMPO’s field of regard (FOR). Due to the computational burden of on-line radiative transfer calculations and limited computational resources, a spatial coadding strategy is applied. Specifically, four native ground pixels in the North-South direction are coadded and provided as a single retrieval pixel. Therefore, the product’s spatial resolution is ~8 km x 4.75 km at the center of TEMPO’s FOR, and the imagery resolution is 2 km. The layer is filtered to remove low-quality pixels based on several criteria, using retrieval exit status (removing data that are not converged), solar zenith angle (removing data retrieved at high solar zenith angles), viewing zenith angle (removing data retrieved at high viewing zenith angles), fit RMS (removing with a high ratio of fitting residual to measurement error), average residual (removing data with high average relative fitting residual) and effective cloud fraction (removing where clouds obscure the column) variables. The filters applied are set to remove pixels based on the following: retrieval exit status ≤ 1 and ≥ 99, solar zenith angle greater than 80 degrees, viewing zenith angle greater than 80 degrees, fit RMS greater than 3, average residual greater than 0.3, and effective cloud fraction greater than 0.5.++Ozone profile Level 2 files provide ozone (ozone profile, total ozone column, troposphere ozone column, and stratosphere ozone column) and supporting information at spatial resolution of four North-South direction coadded from TEMPO’s native spatial resolution for individual granules. Each granule covers the entire North-South TEMPO FOR but only a portion of the East-West FOR. The temporal resolution of a nominal scan is approximately one hour during daylight hours, with more frequent scans in the morning over the eastern portion of the FOR and in the evenings over the western portion of the FOR.diff --git a/config/default/common/config/metadata/layers/tempo/TEMPO_L3_Ozone_Profile_Total_Column.md b/config/default/common/config/metadata/layers/tempo/TEMPO_L3_Ozone_Profile_Total_Column.mdnew file mode 100644index 000000000..dfbf48cee--- /dev/null+++ b/config/default/common/config/metadata/layers/tempo/TEMPO_L3_Ozone_Profile_Total_Column.md@@ -0,0 +1,7 @@+The Tropospheric Emissions: Monitoring of Pollution (TEMPO) Total Ozone Column Amount layer provides information on the total amount of ozone in a vertical column of the atmosphere. The retrieval is performed using the Smithsonian Astrophysical Observatory (SAO) ozone profile algorithm, which is based on the optimal estimation method. The total ozone column was calculated by integrating the ozone profile provided in 24 vertical layers.++Imagery is available as approximately one-hour scans for daylight hours over North America. The sensor’s native spatial resolution is ~2 km x 4.75 km at the center of TEMPO’s field of regard (FOR), and the product’s spatial resolution is ~8 km x 4.75 km. The Level 3 product is regridded from the Level 2 product onto a 0.04 longitude x 0.04 latitude grid, and the imagery sampling is 4 km. The layer is filtered to remove low-quality pixels based on several criteria, using solar zenith angle (removing data retrieved at high solar zenith angles), viewing zenith angle (removing data retrieved at high viewing zenith angles), and effective cloud fraction (removing where clouds obscure the column) variables. The filters applied are set to remove pixels based on the following: solar zenith angle greater than 80 degrees, viewing zenith angle greater than 80 degrees, and effective cloud fraction greater than 0.5.++Ozone profile Level 3 files provide ozone (ozone profile, total ozone column, troposphere ozone column, and stratosphere ozone column) and supporting information on a regular grid. Level 3 files are derived by combining information from all Level 2 files constituting a TEMPO East-West scan cycle, using an area-weighted regridding approach. The temporal resolution of a nominal scan is approximately one hour during daylight hours, with more frequent scans in the morning over the eastern portion of the FOR and in the evenings over the western portion of the FOR.++References: TEMPO_O3PROF_L3 [doi:10.5067/IS-40e/TEMPO/O3PROF_L3.004](https://dx.doi.org/10.5067/IS-40e/TEMPO/O3PROF_L3.004)\ No newline at end of filediff --git a/config/default/common/config/metadata/layers/tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column.md b/config/default/common/config/metadata/layers/tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column.mdnew file mode 100644index 000000000..8e0645671--- /dev/null+++ b/config/default/common/config/metadata/layers/tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column.md@@ -0,0 +1,7 @@+The Tropospheric Emissions: Monitoring of Pollution (TEMPO) Ozone Column Amount layer provides information on the total amount of ozone in a vertical column of the troposphere. The retrieval is performed using the Smithsonian Astrophysical Observatory (SAO) ozone profile algorithm, which is based on the optimal estimation method. The troposphere ozone column was calculated by integrating the ozone profile from surface to the tropopause, using tropopause information from the Goddard Earth Observing System Composition Forecast (GEOS-CF) data.++Imagery is available as approximately one-hour scans for daylight hours over North America. The sensor’s native spatial resolution is ~2 km x 4.75 km at the center of TEMPO’s field of regard (FOR), and the product’s spatial resolution is ~8 km x 4.75 km. The Level 3 product is regridded from the Level 2 product onto a 0.04 longitude x 0.04 latitude grid, and the imagery sampling is 4 km. The layer is filtered to remove low-quality pixels based on several criteria, using solar zenith angle (removing data retrieved at high solar zenith angles), viewing zenith angle (removing data retrieved at high viewing zenith angles), and effective cloud fraction (removing where clouds obscure the column) variables. The filters applied are set to remove pixels based on the following: solar zenith angle greater than 80 degrees, viewing zenith angle greater than 80 degrees, and effective cloud fraction greater than 0.5.++Ozone profile Level 3 files provide ozone (ozone profile, total ozone column, troposphere ozone column, and stratosphere ozone column) and supporting information on a regular grid. Level 3 files are derived by combining information from all Level 2 files constituting a TEMPO East-West scan cycle, using an area-weighted regridding approach. The temporal resolution of a nominal scan is approximately one hour during daylight hours, with more frequent scans in the morning over the eastern portion of the FOR and in the evenings over the western portion of the FOR.++References: TEMPO_O3PROF_L3 [doi:10.5067/IS-40e/TEMPO/O3PROF_L3.004](https://dx.doi.org/10.5067/IS-40e/TEMPO/O3PROF_L3.004)\ No newline at end of filediff --git a/config/default/common/config/wv.json/layerOrder.json b/config/default/common/config/wv.json/layerOrder.jsonindex 830c93e3c..4ce76b8b0 100644--- a/config/default/common/config/wv.json/layerOrder.json+++ b/config/default/common/config/wv.json/layerOrder.json@@ -113,6 +113,8 @@"TEMPO_L3_Ozone_Column_Amount","TEMPO_L3_Ozone_Cloud_Fraction","TEMPO_L3_Ozone_UV_Aerosol_Index",+ "TEMPO_L3_Ozone_Profile_Total_Column",+ "TEMPO_L3_Ozone_Profile_Troposphere_Column","VIIRS_NOAA21_DayNightBand","VIIRS_NOAA20_DayNightBand_At_Sensor_Radiance","VIIRS_NOAA20_DayNightBand_AtSensor_M15",diff --git a/config/default/common/config/wv.json/layers/tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule.json b/config/default/common/config/wv.json/layers/tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule.jsonnew file mode 100644index 000000000..789e1391a--- /dev/null+++ b/config/default/common/config/wv.json/layers/tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule.json@@ -0,0 +1,19 @@+{+ "layers": {+ "TEMPO_L2_Ozone_Profile_Total_Column_Granule": {+ "id": "TEMPO_L2_Ozone_Profile_Total_Column_Granule",+ "title": "Ozone Profile (L2, Total Ozone Column, Subdaily) (BETA)",+ "subtitle": "TEMPO",+ "description": "tempo/TEMPO_L2_Ozone_Profile_Total_Column_Granule",+ "tags": "",+ "group": "overlays",+ "layergroup": "Ozone",+ "type": "granule",+ "period": "subdaily",+ "count": 1,+ "dataAvailability": "dd",+ "disableSnapshot": true,+ "shiftadjacentdays": false+ }+ }+}\ No newline at end of filediff --git a/config/default/common/config/wv.json/layers/tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.json b/config/default/common/config/wv.json/layers/tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.jsonnew file mode 100644index 000000000..8e18a81df--- /dev/null+++ b/config/default/common/config/wv.json/layers/tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.json@@ -0,0 +1,19 @@+{+ "layers": {+ "TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule": {+ "id": "TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule",+ "title": "Ozone Profile (L2, Tropospheric Ozone Column, Subdaily) (BETA)",+ "subtitle": "TEMPO",+ "description": "tempo/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule",+ "tags": "",+ "group": "overlays",+ "layergroup": "Ozone",+ "type": "granule",+ "period": "subdaily",+ "count": 1,+ "dataAvailability": "dd",+ "disableSnapshot": true,+ "shiftadjacentdays": false+ }+ }+}\ No newline at end of filediff --git a/config/default/common/config/wv.json/layers/tempo/TEMPO_L3_Ozone_Profile_Total_Column.json b/config/default/common/config/wv.json/layers/tempo/TEMPO_L3_Ozone_Profile_Total_Column.jsonnew file mode 100644index 000000000..45454540e--- /dev/null+++ b/config/default/common/config/wv.json/layers/tempo/TEMPO_L3_Ozone_Profile_Total_Column.json@@ -0,0 +1,15 @@+{+ "layers": {+ "TEMPO_L3_Ozone_Profile_Total_Column": {+ "id": "TEMPO_L3_Ozone_Profile_Total_Column",+ "title": "Ozone Profile (L3, Total Ozone Column, Subdaily) (BETA)",+ "subtitle": "TEMPO",+ "description": "tempo/TEMPO_L3_Ozone_Profile_Total_Column",+ "tags": "",+ "group": "overlays",+ "layergroup": "Ozone",+ "dataAvailability": "dd",+ "shiftadjacentdays": false+ }+ }+}\ No newline at end of filediff --git a/config/default/common/config/wv.json/layers/tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column.json b/config/default/common/config/wv.json/layers/tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column.jsonnew file mode 100644index 000000000..ec196b87a--- /dev/null+++ b/config/default/common/config/wv.json/layers/tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column.json@@ -0,0 +1,15 @@+{+ "layers": {+ "TEMPO_L3_Ozone_Profile_Troposphere_Column": {+ "id": "TEMPO_L3_Ozone_Profile_Troposphere_Column",+ "title": "Ozone Profile (L3, Tropospheric Ozone Column, Subdaily) (BETA)",+ "subtitle": "TEMPO",+ "description": "tempo/TEMPO_L3_Ozone_Profile_Troposphere_Column",+ "tags": "",+ "group": "overlays",+ "layergroup": "Ozone",+ "dataAvailability": "dd",+ "shiftadjacentdays": false+ }+ }+}\ No newline at end of filediff --git a/config/default/common/config/wv.json/measurements/Featured - TEMPO.json b/config/default/common/config/wv.json/measurements/Featured - TEMPO.jsonindex 74efd5309..dce9cd5b6 100644--- a/config/default/common/config/wv.json/measurements/Featured - TEMPO.json+++ b/config/default/common/config/wv.json/measurements/Featured - TEMPO.json@@ -26,7 +26,9 @@"TEMPO_L3_Cloud_Cloud_Pressure_Total","TEMPO_L3_Ozone_Column_Amount","TEMPO_L3_Ozone_Cloud_Fraction",- "TEMPO_L3_Ozone_UV_Aerosol_Index"+ "TEMPO_L3_Ozone_UV_Aerosol_Index",+ "TEMPO_L3_Ozone_Profile_Total_Column",+ "TEMPO_L3_Ozone_Profile_Troposphere_Column"]}}diff --git a/config/default/common/config/wv.json/measurements/Ozone.json b/config/default/common/config/wv.json/measurements/Ozone.jsonindex 4d648a5ad..9365c4a71 100644--- a/config/default/common/config/wv.json/measurements/Ozone.json+++ b/config/default/common/config/wv.json/measurements/Ozone.json@@ -56,7 +56,9 @@"TEMPO_L2_Ozone_Column_Amount_Granule","TEMPO_L2_Ozone_Cloud_Fraction_Granule","TEMPO_L3_Ozone_Column_Amount",- "TEMPO_L3_Ozone_Cloud_Fraction"+ "TEMPO_L3_Ozone_Cloud_Fraction",+ "TEMPO_L3_Ozone_Profile_Total_Column",+ "TEMPO_L3_Ozone_Profile_Troposphere_Column"]},"MERRA-2": {diff --git a/e2e/features/layers/layer-picker-test.spec.js b/e2e/features/layers/layer-picker-test.spec.jsindex 1a50bf773..a1e8399a5 100644--- a/e2e/features/layers/layer-picker-test.spec.js+++ b/e2e/features/layers/layer-picker-test.spec.js@@ -45,7 +45,7 @@ test('"Unavailable" layers show unavailable icon and tooltip', async () => {test('Entering search text transitions to search mode', async () => {const { layersSearchField, layersSearchRow } = selectorsawait layersSearchField.fill('ozone')- await expect(layersSearchRow).toHaveCount(13)+ await expect(layersSearchRow).toHaveCount(15)})test('Updating input changes results', async () => {diff --git a/web/images/layers/previews/geographic/TEMPO_L2_Ozone_Profile_Total_Column_Granule.jpg b/web/images/layers/previews/geographic/TEMPO_L2_Ozone_Profile_Total_Column_Granule.jpgnew file mode 100644index 000000000..ad139322bBinary files /dev/null and b/web/images/layers/previews/geographic/TEMPO_L2_Ozone_Profile_Total_Column_Granule.jpg differdiff --git a/web/images/layers/previews/geographic/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.jpg b/web/images/layers/previews/geographic/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.jpgnew file mode 100644index 000000000..ad139322bBinary files /dev/null and b/web/images/layers/previews/geographic/TEMPO_L2_Ozone_Profile_Troposphere_Column_Granule.jpg differdiff --git a/web/images/layers/previews/geographic/TEMPO_L33_Ozone_Profile_Total_Column.jpg b/web/images/layers/previews/geographic/TEMPO_L33_Ozone_Profile_Total_Column.jpgnew file mode 100644index 000000000..7d9c05ee4--- /dev/null+++ b/web/images/layers/previews/geographic/TEMPO_L33_Ozone_Profile_Total_Column.jpg@@ -0,0 +1,6 @@+<?xml version='1.0' encoding="UTF-8" standalone="no" ?>+<ServiceExceptionReport version="1.3.0" xmlns="http://www.opengis.net/ogc" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.opengis.net/ogc http://schemas.opengis.net/wms/1.3.0/exceptions_1_3_0.xsd">+<ServiceException code="LayerNotDefined">+msWMSLoadGetMapParams(): WMS server error. Invalid layer(s) given in the LAYERS parameter. A layer might be disabled for this request. Check wms/ows_enable_request settings.+</ServiceException>+</ServiceExceptionReport>diff --git a/web/images/layers/previews/geographic/TEMPO_L3_Ozone_Profile_Total_Column.jpg b/web/images/layers/previews/geographic/TEMPO_L3_Ozone_Profile_Total_Column.jpgnew file mode 100644index 000000000..383e615f8Binary files /dev/null and b/web/images/layers/previews/geographic/TEMPO_L3_Ozone_Profile_Total_Column.jpg differdiff --git a/web/images/layers/previews/geographic/TEMPO_L3_Ozone_Profile_Troposphere_Column.jpg b/web/images/layers/previews/geographic/TEMPO_L3_Ozone_Profile_Troposphere_Column.jpgnew file mode 100644index 000000000..089c755c7Binary files /dev/null and b/web/images/layers/previews/geographic/TEMPO_L3_Ozone_Profile_Troposphere_Column.jpg differ