Skip to content

Free, open-source 3D sculpting for Linux, macOS and Windows: dense meshes, remeshing, painting, built-in AI (image/text to 3D), Send to Unreal, game-ready LODs, Gaussian splats and OpenUSD.

7.9 KB
Raw Blame

Your first sculpt in 10 minutes

Never sculpted before? In about ten minutes this lesson turns the default sphere into a cute owl head: ear tufts, a heart-shaped face, big amber eyes under stern brows and a little orange beak. It ends with a render you can share. You only need the built-in brushes, a mouse (a pen tablet is nicer, but not required) and these twelve steps.

The finished owl

The lesson uses the default look: the SculptForge layout, with the menus File, Edit, Sculpt, Paint, Mesh, View, Render, Help along the top, a tool shelf under them, the brushes along the bottom and the Tool panel on the right. If you switched to the Classic layout, the Classic layout notes say where things are there; Preferences, for one, has its own name in the palette bar there instead of sitting under Edit (where Preferences is). Every step can be undone with Ctrl+Z, so experiment freely.

Each brush remembers its own size. To set it, hold the cursor over the canvas, press S, type the number the step gives and press Enter (or drag the slider that appears). [ and ] make it smaller and bigger.

Tip: Help > Your first sculpt (10 min) opens this lesson inside SculptForge any time; Shift+F1 hides it and shows it again where you left off.

1. Start with a sphere

Goal: a fresh sphere, seen from the front.

  1. Press Ctrl+N (File > New Sphere).
  2. Press F to frame it. To look around: drag on the empty background to rotate, Alt + drag on the background to move the view, scroll to zoom. Press F again whenever you lose it.
  3. Check that X is lit on the tool shelf: symmetry is on, so everything you do on one side happens on the other.

The default sphere in the SculptForge layout

Tip: right-drag anywhere rotates the view too, even over the model. See Navigating the view.

2. Pull up the ear tufts

Goal: two pointed tufts on top of the head.

  1. Pick Move: press 4, or click Move on the bottom shelf. Set its size to 110.
  2. Start on the top of the sphere, a little left of the middle, and drag up and out. Symmetry pulls the right tuft.

Two ear tufts pulled up with Move

Tip: if the view turns instead, you started on the background. Undo and start the drag a little further inside the sphere.

3. Dig the face

Goal: two round hollows, the owl's face discs.

  1. Pick Clay: press 2. Set its size to 120.
  2. Hold Alt and click four times where the left eye goes, a little left of the middle and halfway down. With Alt, Clay digs in instead of building up.

Two face discs dug with Alt+Clay

Tip: a click is one dab of the brush. Several clicks in one place build up (or dig) more.

4. Shape the beak

Goal: a small pointed beak between the eyes.

  1. Pick Inflate: press 5. Set its size to 30 and click three times on the middle line, just below the face discs: a bump.
  2. Pick Move (4), size 30. Drag from the bump a short way down: it points.
  3. Pick Smooth (3), size 24, and drag once down the beak to tidy it.

The beak

Tip: hold Shift and drag to smooth with any brush, whenever a stroke leaves a lump.

5. Add three levels

Goal: enough polygons for crisp eyes and colours.

  1. Press Ctrl+D three times (Tool > Geometry > Add Level). Each new level makes four polygons out of every one and smooths the shape: about 5 million triangles now.

Three levels added: the same shape, smoother

Tip: sculptors block out the big shapes on a light mesh, then divide for details. Shift+D and D step down and up the levels. See Subdivision levels.

6. Add the eyes

Goal: big round eyeballs in the face discs.

  1. Pick Inflate (5), size 52.
  2. Click three times in the middle of the left face disc. Symmetry adds the right eye.

Eyes inflated in the face discs

Tip: Inflate swells the surface along its normals, so dabs make round, even bulges.

7. Give it brows

Goal: a V of brows that gives the owl its look.

  1. Pick Clay (2), size 30.
  2. Drag twice from between the eyes up and out over the left eye.

Brows built up with Clay

Tip: the angle of the brows sets the mood: up and out for a stern owl, flatter for a sleepy one.

8. Colour it brown

Goal: warm brown feathers everywhere.

  1. Open Paint. In Vertex Paint & Color, pick a warm brown in the colour wheel and click Fill.

The owl filled brown

9. Paint the face

Goal: soft cream face discs.

  1. Press P (or click Paint on the tool shelf): the brush now paints colour without changing the shape. Set its size to 100.
  2. Make the edge soft: with the cursor over the canvas press O (Falloff), type 0 and press Enter.
  3. Pick a cream colour and click twice on the left face disc.

Cream face discs

Tip: a soft edge blends one colour into the next, like feathers.

10. Paint the eyes

Goal: amber eyes with black pupils and a glint.

  1. Give the brush a hard edge: O, type -100, Enter.
  2. Size 44, amber: click once in the middle of the left eye.
  3. Size 24, black: click once in the same spot for the pupil.
  4. Size 8, white: click once at the top left of the pupil for the glint.

Amber eyes, pupils and glints

Tip: C over the model picks up the colour under the cursor, and Alt paints back towards white. See Vertex Paint.

11. Paint the beak and tufts

Goal: an orange beak and darker tuft tips.

  1. Size 16, orange: drag down the beak, twice.
  2. Soft edge again (O, 0, Enter), size 70, dark brown: click twice on the tip of the left tuft.
  3. Press P again to go back to sculpting.

Beak and tufts painted

12. Shade it and save a render

Goal: a picture of your sculpt to share.

  1. Press M over the canvas and click White: a clean material that shows your colours.
  2. Open Render > Materials and click PBR under Viewport Shading: soft studio light with gentle reflections.
  3. Turn the view to a three-quarter angle, a little from above, and press F.
  4. Click Save Render at the bottom of Render > Materials. The status bar names the picture (twice the size of the view); find it under Library > Image. Size and the shape buttons (1:1, 16:9, 9:16, 4:3) below it make a bigger or differently shaped picture, as a PNG or a JPG. Light, above it, turns the light around the model.
  5. Press Ctrl+S to save the project.

Render > Materials with PBR shading and Save Render

Well done: that's a sculpt, painted and rendered.

What's next